Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 1771 - 1785 of 2268 products found.

  • YODA Profiler

    JFE Advantech Co., Ltd.

    The YODA profiler (“Yoing” Ocean Data Acquisition Profiler) is a “tow-yo” instrument to profile the water column with high spatial resolution from small boats without occupying much space. The instrument is provided with a deployment winch and sensors measuring conductivity, temperature, pressure, chlorophyll, turbidity and dissolved oxygen. The brush at the top of the instrument allows for a stabilizing effect on the free-fall sinking speed, which is approximately constant at 0.2 m/s. All data are stored internally and downloaded into a PC through a wet-connector and interface.

  • Triple-Axis Gyro Breakout Board

    L3GD20H - Adafruit

    A gyroscope is a type of sensor that can sense twisting and turning motions. Often paired with an accelerometer, you can use these to do 3D motion capture and inertial measurement (that is - you can tell how an object is moving!) As these sensors become more popular and easier to manufacture, the prices for them have dropped to the point where you can easily afford a triple-axis gyro! Only a decade ago, this space-tech sensor would have been hundreds of dollars.

  • Biaxial Clip-on Extensionmeters

    Instron

    The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen and a third sensor measures transverse strain. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.

  • Averaging Clip-on Extensometer

    Instron

    The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.

  • Gentle Breeze Pressure Measurement System

    Kyowa Instruments

    The measurement system capable of simultaneously measuring gentle breeze pressure changes of wind tunnel and performing data processing through multiple dedicated micro-pressure sensors. For example, the system can make wind tunnel experiments for building models, and predict and improve the wind pressure suffered by buildings and the wind effect onsurrounding buildings. In addition it is used to measure indoor air pressure distribution. It is used for research of improvement in the amenity by the ventilation method.

  • Scanning Probe Microscopy

    SPECS Surface Nano Analysis GmbH

    As Scanning Probe Microscopy (SPM) is a key tool for nanotechnology, SPECS offers dedicated solutions for highly demanding requirements.In UHV, strong emphasis lies on spectroscopic methods such as scanning tunneling spectroscopy and inelastic tunneling spectroscopy as well as single atom and molecule manipulation. With the invention of a Joule-Thomson cryostat by Prof. Wulf Wulfhekel, SPECS now offers the JT-STM , operating sample and sensors in thermal equilibrium below 1K with optional high magnetic field.

  • PXI Strain/Bridge Input Module

    National Instruments

    PXI Strain/Bridge Input Modules feature up to eightchannels that support quarter-, half-, or full-bridge sensors at speeds up to 102.4kS/s. The modules provide increased accuracy, high data throughput, and a range of synchronization features. Optional features include remote sensing, internal bridge completion, and shunt calibration options per channel. PXI Strain/Bridge Input Modules are ideal for dynamic strain, load and pressure measurements, and test cell installations requiring accuracy and flexibility.

  • Signature Compression Only Load Button Load Cells

    SLB SERIES - Transducer Techniques, Inc

    The SLB Series Subminiature load cells (Load Buttons) are offered for compression only applications where space is limited. The matching surface must be flat for ultimate accuracy. The loading diameter is slightly convex for accurate load distribution. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.

  • Low Profile Compression Only Load Button Load Cell with Mounting Holes

    LBC SERIES - Transducer Techniques, Inc

    The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.

  • Load Cell

    Futek Advanced Sensor Technology, Inc.

    Load Cells manufactured in US by FUTEK Advanced Sensor Technology (FUTEK), a leading manufacturer producing a huge selection of Load Cells, utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.A Load Cell is defined as a transducer that converts an input mechanical force into an electrical output signal. Load Cells are also commonly known as Load Transducers or Load Sensors.

  • Low Profile Compression Only Load Button Load Cell with Mounting

    LBO SERIES - Transducer Techniques, Inc

    The LBO Series (Load Button) load cells are offered for compression only applications where space is limited. Matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4phstainless steel and sealed for use in mostindustrial environments.

  • PXIe Optical to 4 port USB 2.0 Hub

    M9407A - Keysight Technologies

    Designed to complement the M9403A and M9404A Optical Link, the M9406A and M9407A is a fully compliant USB 2.0 Hub. The optically extended USB ports enable remote operation and utilize USB devices at the remote end of the optical link. Devices such as USB keyboards, mouse, USB video adapter for a remote monitor can be used for remote control. USB power sensors as well as E-Cal modules can be used to set up measurements. Remote extension of USB devices such as;

  • PXIe Optical to USB 2.0

    M9406A - Keysight Technologies

    Designed to complement the M9403A and M9404A Optical Link, the M9406A and M9407A is a fully compliant USB 2.0 Hub. The optically extended USB ports enable remote operation and utilize USB devices at the remote end of the optical link. Devices such as USB keyboards, mouse, USB video adapter for a remote monitor can be used for remote control. USB power sensors as well as E-Cal modules can be used to set up measurements. Remote extension of USB devices such as;

  • Pressure Cell Transducer

    Unitech Scales And Measurements Pvt. Ltd

    Unitech’s Pressure Transducers manufactures a wide range of absolute and true gauge pressure transducers.Unitech’s Pressure Transducer is mainly a strain gauge based sensors ranging form Vacuum to 1200 Kg/cm2. The stainless steel construction permits the transducers to operate in rugged, industrial environments. We also undertake custom-built pressure transducer for specific requirement and for OEM users.

  • Pressure Comparators

    AMETEK Sensors, Test & Calibration

    Our high-pressure, hydraulic pressure comparators are portable, self-contained, hydraulic pressure generators for calibrating pressure gauges, transmitters, sensors, and safety valves. They are much faster than deadweight testers and most automated pressure controllers; and it’s so quick and easy to use, it’s ideal for calibrating those low cost gauges that are often overlooked for ISO9000 compliance. Each pump is available on its own, or in one of our complete ready-to-use pump systems.