Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 1906 - 1920 of 2268 products found.

  • Data Acquisition Instruments (DAQ)

    NH Research, Inc.

    Each data acquisition device channel provides its own high resolution 24-bit DAQ, a separate per channel measurement range, and each channel is fully isolated from all other channels. This makes it possible for adjacent voltage channels to measure cell voltages as well as module, string and pack voltages at the same time (figure 1). Additionally, temperature measurement channels are independently programmable for each thermocouple type (B, E, J, K, N, R, S, and/or T) allowing any combination of temperature sensors to be used.

  • Data Aquisition System

    KiDAQ - Kistler Instrument Corp.

    KiDAQ is an innovative, modular data acquisition system (DAQ) from Kistler. With it, you can create your test setup, perform your measurements and achieve reliable results almost instantly. Our expertise covers the entire measuring chain, from the sensor, to signal conditioning, and on to the software. The KiDAQ data acquisition system can be expanded at any time with measuring modules and measuring units. Third-party sensors can also be integrated into the system. Our unique software guides you step-by-step through the measurement setup and provides the user with valuable insight over the entire measuring chain.

  • DC Milligauss Meter

    MGM - Alpha Lab, Inc.

    An improvement on the flux gate magnetometer, the DC Milligauss Meter measures magnetic fields (technically "flux density") up to several times the strength of the Earth field. It has a resolution of 0.01 milligauss (1 nanotesla) and a range of +/-2000 milligauss (200 microteslas). The meter's magnetoresistive sensor is a major improvement over an uncompensated fluxgate magnetometer both in cost and stability. In fact, this sensor approaches a proton precession magnetometer in temperature stability. However, at only 1 mm x 0.2 mm, the active sensor area is much smaller than fluxgate magnetometer or proton sensors. This allows very precise magnetic measurements in small areas (such as thin films) or with high gradients, when necessary.

  • Logger version 2-D electro-magnetic current meter for deep ocean

    INFINITY-Deep AEMD-USB - JFE Advantech Co., Ltd.

    INFINITY-Deep is an autonomously deployable data logger for current speed measurements in the deep oceans. The currents in the deep oceans are very weak. It is too hard to accurately measure the deep water currents by some ADVs (Acoustic Doppler Velocimeters) that detect the Doppler-effect by scatter with the suspended particles in the water, because the concentration is very low. INFINITY-Deep measures 2-D current data through a magnetic field according to Faraday's law. Therefore, even if the suspended particles do not exist around the sensor, it can provide the accurate current data. The depth rating is 6,000m. Compared to INFINITY-EM, the instrument has a depth and a tilt sensors to monitor mooring status. Also, the battery capacity doubles for long-term current velocity measurements.

  • Multifunction board

    APCI-3110-16 - TEAM SOLUTIONS, INC.

    The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.

  • Multi Function Tribometer

    MFT-5000 - Rtec Instruments

    The state of the art Rtec Multi Function tribometer Mft-5000 is globally regarded as the most versatile and technologically advanced tribometer. Manufactured at silicon valley, California it is used by several top labs, universities and industries. The tribometer offers next generation patented force sensors with ultra low resolution, highest speeds and wide environmental control range than any other commercially existing tribometer. The patented integrated 3D profilometer allows to analyse surface change vs time. The universal tribometer MFT5000 allows to create a comprehensive report on friction, wear, tribology and surface analysis.

  • Multispectral Cameras

    PixelCam - PIXELTEQ

    PixelCam™ multispectral cameras provide live imaging of 3-9 spectral bands at video rates. Simultaneous multi-channel “snapshot” acquisition delivers rich, real-time data without scene change or pixel shift. Custom dichroic filter arrays are integrated into the focal plane array at wafer-level to create robust linear and area sensors that extract high-contrast spectral information at specific visible and infrared wavelengths. This breakthrough technology enables easy integration into handheld, mobile and aerial cameras – all with the same frame rate, size, weight, and power consumption as monochrome cameras.

  • Modbus Data Logger

    Ajinkya Electronic Systems

    Modbus is a popular protocol that is used by manufacturers of instruments and sensors. Site instrumentation already exists and parameters to be recorded are available on Modbus Data Logger. We have in store fro our clients Modbus Data Logger that can read data from these instruments and record them periodically. These loggers are configured as per the site requirements. Though basic operation of any data logger is to record the values of process parameters. However it is important that recorded data is presented to the user in timely and prescribed manner. Also any discrepancies in the readings are conveyed to the operator in the fastest manner for quick action.

  • Measuring devices for magnetically soft materials

    MAG-TD200 - R&J Measurement

    In case of alternating field the system uses the following test circuits: Epstein frame, SingleSheetTester, yoke for sample with dimensions (280x30) mm, yoke for sample with dimensions (100x100) mm and toroidal sample. There is also a possibility to use another test circuits according to customer''s requests. When test circuits, mentioned above are equipped with appropriate sensors, the system allows measuring dynamic magnetic properties based on indirect or direct measurement of magnetic field strength. The system is able to measure the properties of ferromagnetic materials in alternating field with simultaneous determination of field strength by direct and indirect method, as well.

  • M2M / IoT Gateways

    Eurotech Inc

    *M2M/IoT Gateways close the gap between devices in the field and the Cloud, where data is collected, stored and manipulated by business applications. *The M2M/IoT Gateway, instantiate a bidirectional communication between the field and the Cloud; moreover, high-end IoT Gateway offer local processing and storage capabilities to provide offline services and almost real time control over the devices in the field. *Multi-Service IoT Gateways are ideally suited for M2M applications to connect sensors, actuators, and devices to the business enterprise. *Key functionalities include a wide array of secure connectivity solutions through cellular, Wi-Fi, Bluetooth and Zigbee networks.

  • Magcam MiniCube1D

    MagCam NV

    Magcam's MiniCube1Dmagnetic field camera provides quantitativeBz magnetic field mapping in a 12.7mm x 12.7mm 2D planewith 0.1mm spatial resolution, measured at high speed. The camera is based on Magcam's unique integrated 2D Hall sensor array technology, featuring more than 16000 microscopic magnetic field sensors on one single chip. Each sensor independently measures the local magnetic field, resulting in quantitative2D magnetic field maps with high spatial resolution, measured athigh speed. These magnetic field maps contain a large amount of information about the magnet's properties, which can be extracted using Magcam's powerful MagScope measurement and analysis software.

  • Magmeter Flow Sensor

    2551 - Georg Fischer Signet

    The Signet 2551 Magmeter is an insertion-style magnetic flow sensor that features no moving parts. The patented* sensor design is available in corrosion-resistant materials to provide long-term reliability with minimal maintenance costs. Material options include PP with stainless steel, PVDF with Hastelloy-C, or PVDF with Titanium. Utilizing the comprehensive line of Signet installation fittings, sensor alignment and insertion depth is automatic. These versatile, simple-to-install sensors deliver accurate flow measurement over a wide dynamic range in pipe sizes ranging from DN15 to DN900 ( to 36 in.), satisfying the requirements of many diverse applications.

  • Industrial Pressure Calibrator

    2271A - Fluke Calibration

    The Fluke Calibration 2271A Industrial Pressure Calibrator provides a complete, automated solution for calibrating a wide variety of pressure gauges and sensors. Thanks to its modular design, it can be configured to meet different needs and budgets, and expanded to cover a broad workload. The 2271A is ideal for calibration laboratories starting out in pressure calibration because it offers wide pressure measurement capabilities in a single instrument. Everything you need for calibrating pressure is included; just connect supply pressure. And your investment will stand the test of time: as your workload grows and changes, the 2271A can grow and change too. Just add measurement modules.

  • Isolated Process Control Signal Conditioning Products

    SCIM7B - Bee Instruments

    SCIM7B Isolated Process Control Signal Conditioning Modules provide a complete selection of backpanels DIN rail mounting accessories, interface cables and rack mounting hardware.Each SCIM7B module provides a single of isolated analog input or output. Various input modules accept analog voltage or current signals from all types of field sensors and sources, filter, isolateamplify, linearize and convert these input signals to high-level analog outputs suitable for use in a process control system. Output modules accept high-level analog voltage signals from a process control system, then buffer, isolate, filter, convert and amplify before providing a current or voltage output to a fielddevice.

  • Infrared Gas Analyzers

    Campbell Scientific, Inc.

    Campbell Scientific offers both open-path and closed-path infrared gas analyzers for measuring carbon dioxide and water vapor. Campbell Scientific also offers a closed-path analyzer for measuring methane, nitrous oxide, or isotopologs of carbon dioxide. Designed specifically for eddy-covariance flux measurements, these analyzers offer the following benefits: integrated system design, aerodynamic intake or analyzer body, low power, synchronized measurements with the sonic anemometer, reduced spatial separation between analyzer and sonic anemometer, unrivaled flexibility in data acquisition, and data collection from additional system sensors with Campbell Scientific dataloggers.