Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 1921 - 1935 of 2269 products found.

  • Laser Diode Temperature Controllers

    Newport Corporation

    Thermoelectric temperature controllers are used to control a thermoelectric cooler (TEC) that is typically integrated into a laser diode's package or part of a temperature controlled mounting plate. Laser diode operation is affected by temperature. Precision temperature control will help maintain output power and wavelength as well as prevent against over temperature conditions that can damage or prematurely age laser diodes. Temperature controllers may also be used to control other optical electric devices in research and development or manufacturing test. Careful attention to the design of the temperature controllers provide high stability either with easy to set up Hybrid P-I control loop or with a full PID control loop. For PID control loops, ILX Lightwave instruments contain an autotune method to reduce time to configure the temperature controller for your application. Most ILX Lightwave temperature controllers are compatible with multiple types of temperature sensors including thermistors, AD590, LM335, and RTD sensors.  Please see our Diode Temperature Controller Guide for more information.

  • Motor Testing Equipment for EOL- BLDC (Brushless) Motors

    MotorLine® - MLI-B - M.E.A. Testing Systems Ltd.

    *Performs QA testing on 100% of production without compromising line throughput (up to 10 motors per minute), reducing costs of defective products.*Determines acceptability to user predefined PASS/FAIL limits on production lines.*Provides motor performance data, from stall up to no-load, within seconds, including: torque, speed, current, voltage, input power, output power, time, motor efficiency, driver efficiency, direction of rotation.*Provides dynamic performance tests data, including: speed and torque spectrum, speed and torque oscillations, friction torque, friction spectrum, friction output power, cogging torque level.*Supports non-contact frictionless sensors.*Supports motor’s internal speed sensors.*Support sensorless BLDC motors.*Speed range up to 250,000 rpm.*Motor power switching is done by the motor electronics; the data sampling is started while the motor starts moving.*Motors can be tested inside their applications.*Motor performance data can be recorded in the system database for comparison and statistical analysis.*Test results are provided graphically and tabulated.*Test reports in PDF and Excel format.*Capability for integration with third party devices, such as hipot & insulation resistance testers.

  • Motor Testing Equipment Kits for EOL (End of Line) Production- BLDC Motors

    MotorLine Kit® - MLIK-B - M.E.A. Testing Systems Ltd.

    *Performs QA testing on 100% of production without compromising line throughput (up to 10 motors per minute), reducing costs of defective products.*Determines acceptability to user predefined PASS/FAIL limits on production lines.*Provides motor performance data, from stall up to no-load, within seconds, including: torque, speed, current, voltage, input power, output power, time, motor efficiency, driver efficiency, direction of rotation.*Provides dynamic performance tests data, including: speed and torque spectrum, speed and torque oscillations, friction torque, friction spectrum, friction output power, cogging torque level.*Supports non-contact frictionless sensors.*Supports motor’s internal speed sensors.*Support sensorless BLDC motors.*Speed range up to 250,000 rpm.*Motor performance data can be recorded in the system database for comparison and statistical analysis.*Motor power switching is done by the motor electronics; the data sampling is started while the motor starts moving.*Motors can be tested inside their applications.*Test results are provided graphically and tabulated.*Test reports in PDF and Excel format.*Capability for integration with third party devices, such as hipot & insulation resistance testers.

  • Optical CMM Systems

    RedLux Ltd

    Our OmniLux metrology system is highly versatile and provides unparalleled levels of 3D CMM capture for component measurement in seconds. This high precision non contact, metrology system is extremely versatile because it measures components of any geometry and of any material. Geometries possible include: spheres, asphere, cylinder, internal bore, cone/taper, step height or freeform in any material such as polished or rough metals or ceramics and polymers. The Omnilux is fast and accurate because, unlike direct contact sensors, the use of optical sensors means that the whole surface can be analysed while the object is suspended in space, ensuring that no damage comes to delicate surfaces. Our easy-to-use software interface, developed from years of experience enables the operator to effortlessly control the system. Rich data analysis, automation and export of results for the immediate generation of reports as well as a compact footprint means OmniLux is the leading solution for production or R&D environments where reducing cycle times is critical to sustainable success.

  • Well Control

    Herrin Design & Manufacturing Co.

    The Herrin Design Model 1644 Well System Pump Control is designed to provide a cost effective means of controlling water system reservoir levels. Through precise monitoring, the Well Control is able to reliably sense reservoir water levels by measuring water pressure at the well head. By monitoring reservoir levels at the well head, it is possible to mount the water system controls in one location, eliminating the costly communications link--leased lines or buried cables--between reservoir level sensors and the pumps. Typically, mechanical sensors at the reservoir deteriorate or are broken frequently due to weather; and communications lines are a large, continued expense.The Well Control tolerates temporary variations in water pressure due to surges and usage. The pump will not start until there is a constant low pressure level for 2-3 (variable) minutes (OFF TIME). This insures the pumps are activated only when necessary. Once the pump is turned on, it remains on for a preset period of time--up to 24 hours (ON TIME). During the pump cycle, the control does not rely on water pressure measurements to indicate if the reservoir is full. This feature eliminates sporadic pumping due to pressure variations created during the pumping cycle.

  • Humidity Chambers

    FW Series - Bemco Inc.

    The Bemco FW Series of mechanically cooled Glass Door Humidity Chambers have a a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH.. These chambers feature direct dry air injection and direct humidity sensors. They operate without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allow operation at 20% RH at 5 C and 50% RH at -14 C!

  • Measuring devices for magnetically soft materials

    MAG-TD200 - R&J Measurement

    In case of alternating field the system uses the following test circuits: Epstein frame, SingleSheetTester, yoke for sample with dimensions (280x30) mm, yoke for sample with dimensions (100x100) mm and toroidal sample. There is also a possibility to use another test circuits according to customer''s requests. When test circuits, mentioned above are equipped with appropriate sensors, the system allows measuring dynamic magnetic properties based on indirect or direct measurement of magnetic field strength. The system is able to measure the properties of ferromagnetic materials in alternating field with simultaneous determination of field strength by direct and indirect method, as well.

  • I/Q Mixers

    971 Series - Milimeter Wave Products, Inc.

    Mi-wave supplies 971 series mixer withI (in phase) and Q (quadrature phase)outputs. They are offered over the RFrange of DC to 110 GHz. Good LO to RFisolation is achieved over a relatively broad RF and LO frequency ranges. Typical IF range is from DC to 5 GHz. Both waveguide and coaxial interfacesare offered as options for RF and LO ports. The mechanical design of these mixers is very compact and can be customized to suit any specific application and outline requirement. These IQ mixers find applications in communication equipment, radar sensors and instrumentation receivers

  • Isolated Process Control Signal Conditioning Products

    SCIM7B - Bee Instruments

    SCIM7B Isolated Process Control Signal Conditioning Modules provide a complete selection of backpanels DIN rail mounting accessories, interface cables and rack mounting hardware.Each SCIM7B module provides a single of isolated analog input or output. Various input modules accept analog voltage or current signals from all types of field sensors and sources, filter, isolateamplify, linearize and convert these input signals to high-level analog outputs suitable for use in a process control system. Output modules accept high-level analog voltage signals from a process control system, then buffer, isolate, filter, convert and amplify before providing a current or voltage output to a fielddevice.

  • Low Profile Compression Only Load Button Load Cell with Mounting

    LBM SERIES - Transducer Techniques, Inc

    The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.

  • Load Cells

    WIM Systems, llc

    The load cells are electronic weight sensors whose purpose is to receive the electrical excitation caused by a certain weight applied to the scale or scale and transmit it to a weight indicator. The load cell is an essential component in any scale or electronic scale and there are in different models and specifications. A Wim load cell is indispensable for a weighing system where accuracy, durability and a fair price are required. WIM-Systems manufactures a wide variety of load cell models, one for every need, as well as offering you all the advice you need You need to choose the model that best meets the particular needs of your weighing system and always with the support of WIM-Systems quality and technology.

  • Leak Noise Logger System

    LNL-1 - Fuji Tecom Inc.

    LNL-1 is an acoustic data logger system designed for detecting and monitoring leakage on water pipelines. * Loggers, equipped with high sensitivity sensors are deployed on pipe fittings such as valves, fire hydrants. The loggers record “minimum noise level” at the points on the pipeline.* Analyser, the recorded data are downloaded by radio communication by the Analyser. And the Analyser shows 3 levels of leak possibilities at given thresholds.* Software, the PC software identifies each logger and visualizes it on the map. The results of Minimum Noise Level are indicated in each area or blocks. The results are displayed as graph. Momentary change of sound is also displayed.

  • M2M / IoT Gateways

    Eurotech Inc

    *M2M/IoT Gateways close the gap between devices in the field and the Cloud, where data is collected, stored and manipulated by business applications. *The M2M/IoT Gateway, instantiate a bidirectional communication between the field and the Cloud; moreover, high-end IoT Gateway offer local processing and storage capabilities to provide offline services and almost real time control over the devices in the field. *Multi-Service IoT Gateways are ideally suited for M2M applications to connect sensors, actuators, and devices to the business enterprise. *Key functionalities include a wide array of secure connectivity solutions through cellular, Wi-Fi, Bluetooth and Zigbee networks.

  • Magcam MiniCube1D

    MagCam NV

    Magcam's MiniCube1Dmagnetic field camera provides quantitativeBz magnetic field mapping in a 12.7mm x 12.7mm 2D planewith 0.1mm spatial resolution, measured at high speed. The camera is based on Magcam's unique integrated 2D Hall sensor array technology, featuring more than 16000 microscopic magnetic field sensors on one single chip. Each sensor independently measures the local magnetic field, resulting in quantitative2D magnetic field maps with high spatial resolution, measured athigh speed. These magnetic field maps contain a large amount of information about the magnet's properties, which can be extracted using Magcam's powerful MagScope measurement and analysis software.

  • Advanced Telemetry System

    HTS-SS - Hitec RCD USA

    Our HTS-SS Advance telemetry sensor station works compatibly with all our existing sensors as well as the HTS-ETEMP, HTS-AS, HTS-VM and HTS-SM.  Delivering on its name, the HTS-SS Advance provides more advanced telemetry capabilities than any other RC telemetry system and is capable of monitoring all types of models.  It also provides engine temperature via the HTS-ETEMP sensor, air speed via the HTS-AS sensor, sensitive rate-of- climb tracking via the HTS-VM sensor and servo performance via the HTS-SM sensor. This leading-edge telemetry module provides the most reliable and comprehensive communication with your model yet. Expect More! Expect Hitec!