Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 2011 - 2025 of 2291 products found.

  • TEV Antenna

    Techimp HQ S.r.L

    TEV sensor is a partial discharge sensor whose working principle is based on a direct Capacitive coupling with a Switchgears earthed metal case. The two ends of TEV sensor can be coupled magnetically to virtually any opening on a metal Surface. It picks up the electric signal given by PD activity onto the two metallic surfaces. Thanks to its special design has high sensitivity, larger than other single ended TEV sensors. His compact and robust design (passive sensor) makes the TEV the optimal sensor for direct installation on medium voltage Switchgears.

  • Thermistor Power Meter

    N432A and 432A - Keysight Technologies

    The 432A / N432A power meter is an automatic, self-balancing power meter for use with temperature compensated thermistor sensors. High efficiency and good radio frequency (RF) match are characteristics of the 478A and 8478B coaxial and 486 series (now discontinued) waveguide thermistor mounts that cover the frequency range 10 MHz to 40 GHz. Each thermistor mount contains data showing the calibration factor and effective efficiency at six frequencies, directly traceable to the U.S. National Institute of Standards and Technology (NIST) at those frequencies where NIST provides calibration service.

  • Thermopile Sensor

    Thermopile - JonDeTech

    The thermopile leads can be arranged in different manners; for most commercial sensors of today, typically, horizontal or “in-the-plane” architecture is used. The reason for this is strictly process related. Microelectronic processes have historically been developed to make lateral structures on silicon wafers. However, this is not always the best sensor solution since the hot and the cold junctions are placed next to each other on the same surface. To use this as a infrared sensor an aperture must be integrated with the thermopile so that the heat radiation strikes only a limited area, i.e. the hot junction of the sensor. In other words, the full surface of horizontally configured thermopilescan’t be used, neither can true “contact mode” be utilized.

  • Low Profile Compression Only Load Button Load Cell with Mounting

    LBM SERIES - Transducer Techniques, Inc

    The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.

  • Data Acquisition & Telemetry Buoy System

    LOTUS - MacArtney A/S

    The MacArtney LOTUS buoy system consists of a spherical buoy corpus made from durable GRP, a turbidity sensor with antifouling wiper, a rechargeable battery pack and a data logger with integrated telemetry modem. The buoy is equipped with an “AQUAlogger 210 TYT” turbidity sensor provided with 4 measuring ranges selected automatically. To avoid biological growth on the optical window, the instrument is equipped with an antifouling wiper. The sensor is protected by a cage firmly attached to the buoyant body.The buoy and the data acquisition system has an open architecture that allows for integration of other types of sensors like CTDs, fluorometers, etc.

  • CMOS Cameras

    Magic - New Imaging Technologies

    New Imaging Technologies proposes a broad range of visible products. From sensors to complete camera systems, all of our products integrate our unique NATIVE WDR capabilities. Our NATIVE WDR™ is a new generation of CMOS imaging technology named MAGIC™ (standing in english for Active Matrix with indexed generated contrast ), capable of generating a highly stable image even under very wide intra scene dynamic range (> 120dB) in a single frame time and without multi-exposure, any setting of knee points or external control. Our products are suited for many demanding applications and industries.

  • Probes

    Type K - ThermoWorks

    No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.

  • Probes

    RTD - ThermoWorks

    No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.

  • Conductivity-Resistivity Sensor Electronics and Integral System with PVDF Sensor

    2850 - Georg Fischer Signet

    The Signet 2850 Conductivity/Resistivity Sensor Electronics are available in various configurations for maximum installation flexibility. The universal mount version is for pipe, wall, or tank mounting and enables single or dual (digital versions only) inputs using any standard Signet Conductivity/Resistivity sensor. The threaded j-box version can be used with these same Signet sensors for submersible sensor mounting. It is also available as a combined integral system configuration for in-line mounting and includes a conductivity electrode in a choice of 0.01, 0.1, 1.0, 10.0 or 20.0 cm-1 cell constants. The 2850 is ideal for applications with a conductivity range of 0.055 to 400,000 S or a resistivity range of 18.2 M to 10 k.

  • Pitot Static Indicator

    ADSE 740 - ATEQ Aviation

    The ADSE 740 is a complete high performance dual pressure Ps and Pt standalone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, MACH-meter, air data computers ...) and sensors.

  • Humidity Calibrator

    OptiCal - Michell Instruments

    The OptiCal is a bench-top, fully self-contained humidity/ temperature calibrator. The system comprises a humidity and temperature controlled chamber that can house up to five or more humidity sensors, depending on their physical dimensions. The humidity and temperature within the chamber are closed-loop controlled and continuously monitored by a precision chilled mirror reference hygrometer.

  • Multiparameter Testrs

    WD-35425-10 - OAKTON Instruments

    Great for water, laboratory or plant use, these multiparameter Testrs feature single-junction pH electrodes for longer life and wider range of sample compatibility. Pin-style conductivity sensors feature stainless steel electrodes for chemical resistance and durability. Replaceable sensor module saves you money by reusing the meter body.

  • Geo-magnetic Ground Scanner

    JESSY SMART - Supracon AG

    JESSY SMART is a novel measuring device for fast three-dimensional geomagnetic mapping of hidden subsurface anomalies. JESSY SMART localizes smallest earth magnetic field gradient inhomogenities in a depths of up to approx. 10 meters. The sensors are mounted onto a cart which can be moved attached to a motor car or alternatively pushed along manually.

  • Sensor / ECU Test Aid

    AUTO DIAGNOSTECH LTD

    This Sensor / ECU Test Aid comprises of various set of wired terminals and connectors ready for connection. It is very useful for the auto electrician to gather, capture data and signal during testing of sensors and simulating of voltages and resistance during diagnosing of the car ECU.

  • Portable Emissions Analyzer

    E6000 - E Instruments International, LLC

    The E6000 is a NEW hand-held industrial combustion flue gas and emissions analyzer that can have up to six gas sensors. The E6000 is an innovation portable emissions monitor for accurate measurements of stack gases from combustion processes including boilers, burners, gas and diesel engines, turbines, furnaces, kilns, heaters, and laboratory analysis.