Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 2086 - 2100 of 2287 products found.

  • GPS Disciplined 10 MHz Frequency Reference

    MtRF-5610 - Mountain RF Sensors

    As the latest addition to a growing product line, Mountain RF Sensors (MtRF) is announcing the MtRF-5610 GPS Disciplined 10 MHz Frequency Reference. With eight outputs, the MtRF-5610 eliminates the need for a separate frequency source and RF distribution unit (or multi-coupler). Along with the 10 MHz outputs, time information is also available via a serial output. The serial output support a 1 PPS mode and NMEA-0183. In the event of loss of GPS signal, the unit will continue to operate as a high-accuracy OCXO until the GPS signal is restored. The 1 PPS signal is accurate to ±35 ns to UTC RMS. The 10 MHz output has a noise floor of -155 dBc. Holdover stability is < ±10us over 24 hours. The MtRF-5610 is designed for an operational temperature range of -20˚C to +60˚C. The MtRF-5610 is available in a 8.66" x 6.50" x 2.03" module or a 1U, 19 inch rackmount enclosure and operates from 90–250 VAC line power.

  • Force Balance Inclinometers

    Columbia Research Laboratories

    Columbia's SI-701 Series of Inclinometers are electronic tilt sensors based on Force Balance Accelerometer technology. They produce high level low impedance output proportional to the sine of the tilt angle. Model SI-701B is a low cost general purpose sensor that can be up-graded with the addition of the Columbia "HP" torquer system (SI-701BI) for greater accuracy and ruggedness. A bi-axial version of both units (SI-702B) is also available. The Model SI-701BI is designed with an output circuit made for 4-20mA data transmission systems for industrial applications. The model SI-701FND is a fluid dampened premium performance inclinometer designed to produce accurate tilt data in extreme shock and vibration environments. The latest addition in the line is Model SI-701WPBI, a waterproof (to 150 feet) inclinometer which operates from a +15 volt supply with 4-20mA output. A single power supply powers both the sensor and the 4-20mA line driver.

  • Light Analysis

    Thorlabs, Inc.

    Welcome to Thorlabs; below you will find links to detectors and instrumentation that measure the various properties of light, a subset of our entire line of photonics products. Thorlabs offers an extensive selection of instruments that measure the properties of light. Our versatile power and energy meters can be used with over 25 different sensors in order to make NIST-traceable power and energy measurements. If the convenience of a meter is not desired, our selection of detectors includes basic photodiodes (uncalibrated and calibrated), photodetectors (biased, amplified, and avalanche), CCD and CMOS arrays, position detectors, integrating spheres, and photomultiplier tubes. The Beam Characterization category contains beam profilers (camera and scanning slit), a wavefront sensor, spectrometers, and interferometers, while the Polarimetery link leads to a selection of instruments used to measure and control the polarization of light.

  • Linear Stages

    Klocke Nanotechnik

    A new set of motorized tables developed by Klocke Nanotechnik allows high strokes at small volumes. The modules are driven by the Nanomotor®. Loads of up to two kg can be moved over centimeters of stroke with down to 2 nm resolution. Manipulation in many degrees of freedom is possible without backlash. The modules NMT xx-L are longer, but thin like a pencil. In most of the NMT-modules position measurement systems can be included without increasing the size. The resolution of the position sensor is better than 10 nm. All NMT modules can easily be fixed onto each other. Very small connectors allow the exchange of a module without removing cables. The NMT-Zxx are modules for vertical movement. They have an internal load compensation to lift up loads. Nanomotor-Grippers and force sensors that can easily be fixed on these modules are available.

  • Moisture Testers for Wood

    PCE Instruments

    At PCE Instruments you will find diverse moisture testers for wood to determine absolute moisture in different wood types. With the help of the moisture testers for wood you will be able to measure with high accuracy moisture in rolled products, forestry woodVery accurate and easy to use Moisture Testers for Wood for professionals, slats, beams, plywood, panels, conglomerates, main beams, window frames, etc. There are two ways of measuring moisture: with or without damaging the material. Moisture testers for wood are characteristic by the measuring principle and the moisture sensors that can be adapted to them. Some moisture testers for wood have special characteristics such as an automatic compensation of temperature. Besides, data can be stored and transferred to a PC or portable computer or characteristic curves can be programmed for specific wood types (only with the model FMD).

  • Monitoring Systems

    PCE Instruments

    Monitoring systems refer to Professional Monitoring Systems used for the immediate and systematic detection (protocol). instruments used for immediate and systematic detection (protocol), the display or monitoring of a process with technical assistance, sensors or others monitoring systems such as cameras. Monitoring systems perform continuous measurements of a central element so that, according to the comparison of the results, conclusions can be drawn in order to react in-time. The main function of monitoring systems is to act in a process or alarm when it is not carried out as desired or when limit values are exceeded. Monitoring systems are an special type of protocols in which different parameters are checked and tested, as for instance, air humidity, temperature, shocks, movements, flooding as well as current load. Video cameras are an essential part of monitoring systems that allow for a better assessment of the critical point situation.

  • Minidatalogger

    HD207/227/206/226 - Delta OHM S.r.L.

    HD206…/HD226… and HD207…/HD227… series dataloggers are low-cost, rugged instruments for a long-term reliable monitoring of temperature and temperature/relative humidity measurements. They are available in different versions: with or without LCD display, with sensors either inside or outside the instrument housing, or with cable connection. The analysis of logged data is made using Delta Log2 software for Windows. The datalogger functions of Start, Stop, Configuration, Data Download and Setting of logging interval are selectable either from keyboard or from a computer. Through a computer, you can define a password to enable the access to configuration data. Typical applications are: monitoring of temperature/humidity during transportation, storage of fresh or frozen foods, fruit, vegetable products and flowers, pharmaceuticals, sensitive and photographic products, paper, explosives, as well as laboratory activities in general.

  • Magnetoresistive Milligauss Meter

    MR3 - Alpha Lab, Inc.

    The MR3 Magnetoresistive Milligauss Meter measures and displays the three vectorcomponents (X, Y, Z) as well as the magnitude (M) of the static magnetic field. Update is two times per second. The three sensors are in a 25 mm (1") cube at the end of a flexible 100 cm (40") cable. It can be powered by 4 AA batteries (included) or a Worldwide AC adaptor (included). It can collect and store data (X, Y, Z and M) for later download or stream data live via USB connector. Both the instantaneous values of X, Y, Z and M, and their peak values, are displayed on the meter screen. "Peak" values are the highest values seen since the peak reset button was pressed. Maximum error of sensitivity is +/- 0.5 % of the reading, and the maximum error of the offset is +/- 0.50 milligauss. Range is +/- 1999.99 milligauss with resolution 0.01 milligauss (or 1 nT) over the full range, displayed simultaneously for X, Y, Z and M.

  • Multi Channel Data Logger

    IM2000 N - Ajinkya Electronic Systems

    These are manufacturer, Exporter, Supplier of Data Logggers. A data logger can accept inputs from one or from many sources and number of channels is an additional parameter that defines the type of logger. The IM2000 Series Multichannel Data Logger offered by us can accept inputs from 2 / 4/ 6 / 8 / 12/ 16 / 20 / 24 / 32 / 48 sources. These are available from 2 to up to 48 channels. The type of sensors that a logger would accept can be of a one particular type or combination of different types or Universal Type. Eg. 16 channels RTD Data Logger or 16 channel K type data logger or it can be data logger which accepts 4 inputs of RTD type and 12 inputs of 4-20mA type. So one can appreciate there can be infinite such type of combinations.

  • Machine Vision Lens

    FUJINON HF6XA-5M - FujiFilm Corp.

    This new product, which has an external diameter of 39 mm and a focal length of 6 mm, is the world's smallest* Machine Vision lens which is used for industrial processes such as product inspection and measurement on production lines. HF6XA is a new lens which is designed for compatibility with 2/3" sensors with a pixel pitch of 3.45m (five megapixels). HF6XA is a FUJINON Machine Vision lens designed for compatibility with 2/3" sensors, which has coverage of approximately twice*** the current product, the FUJINON HF8XA, which offers the widest coverage range. In the frequently used environments of customers, the lens is compatible with the ultra-high resolution of 3.45m pixel pitch (equivalent to five megapixels when using a 2/3" sensor) under a large portion of the screen. Furthermore, for a wide range of installations and shooting conditions, the lens boasts "4D High Resolution"*4 performance, mitigating resolution degradation that typically occurs when changing a shooting distance or aperture value and maintaining a high level of even image sharpness across the entire image area at the ultra-high resolution of 4.4m pixel pitch (equivalent to three megapixels when using a 2/3" sensor). Despite being a wide-angle 6mm lens, the lens achieves the world's smallest external diameter of just 39 mm. The lens is ideal for attachment inside compact inspection devices with restricted internal space when wide coverage and consistency is required for reading product codes and serial numbers or for inspecting product shape and appearance.

  • Lasers & Light Sources

    SLEDS - AMS Technologies AG

    A variant of the LED, superluminescent LEDS (or SLEDs) provide the usual broadband, quasi-directional and low temporal coherence light emission common to the ubiquitous LED, but with the added benefit of higher optical power and greater spatial coherence. These properties make SLEDs the better option for numerous applications including telecom, instrumentation, optical coherence tomography (OCT), structual sensors and fiber optic gyroscopes that require this type of broadband source.

  • LED Test

    Optomistic Products

    Universal LightProbe Penta sensors are Optomistic Products' most popular LED test sensor, relied upon for their versatility in accommodating most LED test applications for color and intensity. The Penta Sensor provides analog voltage outputs, and features built-in color binning, eliminating the need to convert LED wavelength to visual color in the ATE software, and saving valuable processing time. For use with any of the Universal LightProbe Fiber-Optic Probes.

  • Fiber optic thermometer systems

    TS Series - Micronor AG

    Micronor now offers a complete range of fiber optic temperature sensors, probes and interfaces for temperature measurement in challenging environments. TS series fiber optic temperature probes offer immunity to RF and microwave radiation along with wide temperature range, intrinsic safety and non-invasive use. The fiber optic temperature probes can operate over -200°C to +300°C (-328°F to +572°C), and withstand harsh and corrosive environments. Typical fiber optic temperature monitoring applications include:

  • Fiber Optic Temperature Sensor with the EasyDisk

    The TPT-62 - FISO Technologies Inc.

    The TPT-62 fiber-optic temperature probe family employs industry standard 62.5µm core OM1 fiber optic for highly improved optical, mechanical, and reliability properties over legacy 200 µm core (1st generation) fiber optic sensors. The EasyDisk sensor tip assembly ensures IEC60076-2 (Annex E) compliant installation and enables quick insertion of the probes into the spacers within the windings of transformers.

  • Force Sensor Elements

    Variohm Eurosensor Ltd

    The STL Force Sensing Tension Links are a series of unique force sensors. The Tension Links utilize the internal strain gage process sucessfully and are used in bolts, load pins and flat load cells. The sensing element consists of a strain gage bridge circuit internally installed in a small hole along the longitudinal axis. This unique arrangement provides a most effective means for the protective sealing of the internal electronics while minimizing the adverse effects of extraneous torsion and bending loads.