Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement


Showing results 2101 - 2109 of 2109 products found.

  • PXI Strain Gauge Simulator Module 4-Channel, 2k

    40-265-304 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 2k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 4-Channel, 1k

    40-265-204 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 1.5k

    40-265-406 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1.5k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 6-Channel, 350

    40-265-016 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 350) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 4-Channel, 3k

    40-265-104 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 3k) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • PXI Strain Gauge Simulator Module 2-Channel, 350 Ohm

    40-265-012 - Pickering Interfaces Ltd.

    The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions. Each simulator channel includes an independent input for the Excitation Voltage and a bridge output. The Excitation Voltage port can be driven by an AC or a DC source. The bridge circuit includes three fixed resistors and a fourth programmable resistor that can be adjusted over a narrow resistance range with fine adjustment capability and excellent accuracy. The adjustment range provided is sufficient to simulate quarter, half or full bridge circuits. The standard bridge impedances are 350, 1k, 1.5k, 2k and 3k. These modules are extremely simple to use, the variable resistor element can be programmed using a simple resistance call. The module supplies the user with the resistance value required to balance the bridge, and the resistance call to the simulator can be varied above and below this value to simulate extension and compression of the strain gauge resistor.

  • Automatic Water Meter Test Bench

    SHANGHAI POWOO INDUSTRY

    System features It can test according to ISO 4064 or OIML R49 For the same lot of water meters, you need to have parameters setting only for one time. WA10-DN15-DN25 for 1-10 meters in series. Adopt laser testing head from Japanese SUNX and numerical laser sensor amplifier. Laser testing head has virtues of small optical spot (0.2mm), long verification distance (reach 500mm). Numerical laser sensor amplifier can respond very rapidly ( Maximum speed: 80 microsecond ,that is, 12.5KHz/s) It has focusing instructed function. Adopt TCS Series Electronic Balance from one of largest electronic scale sensors manufacturer companies in China. The scale has virtues of high precision, high stability, easy operation, convenient information collection etc. It has instantaneous flow adjusting function. It has automatic abrasion test function of ten thousand times (interrupting test, or to say fatigue test). (No need to purchase ten thousand times wear tester specially). It has the functions of automatic monitoring, display of pressure and water temperature in pipeline. It can have verification repeatedly, and you needn't reset the parameters. It can print various reports respectively. It can have pressure verification for water meter. All the information about the tested water meter will be collected, calculated, displayed and transmitted by independent optical collector and adjustable optical sensor. The equipment has water circulated function, and has virtues of low noise, high stability. It can adapt to all kinds of mechanical water meters verification, and is very flexible. The equipment is made of 304 stainless steel and copper. Sufficient spares for wearing parts are (like o washer etc). Low fault rate, convenient repair.n With full technical documents.

  • Voltage Variable Attenuator

    Pasternack Enterprises, Inc.

    Voltage variable attenuator series offers up to 60 dB of attenuation across broad frequencies. The frequency range of the voltage variable attenuator components is from 400 MHz to 18 GHz. This line of voltage variable attenuators is most commonly deployed in applications such as electronic warfare, instrumentation, point-to-point and point-to-multipoint radios, fiber optic and broadband telecom, microwave radio and VSAT, military radios, radar, ECM, SATCOM and sensors, and R&D.In most communications systems, the RF components used (transmitters, receivers, mixers, multipliers, attenuators, amplifiers, VCO’s, phase locked loops, etc.) may require specific power levels to run optimally. These power levels may differ from one component to the next in a system network. These may require the attenuation level to be finely adjusted to account for changes in received signal levels or to optimally match the input power into a sensitive circuit.Pasternack’s PIN diode-based voltage variable attenuators (VVAs) provide accurate control and broadband flatness where the output level can be adjusted continuously by varying an analog voltage on the input control line. These VVA’s are ideally suited for use with variable gain amplifiers, power level control, feed-forward amplifiers, and automatic level control (ALC) circuits.Like the other over 40,000 RF, microwave and millimeter wave components from Pasternack, this voltage variable attenuator VVA series is in-stock. Not only are these VVA components in stock, they will ship the same day as ordered.

  • Portable Trace-Level O3 Calibrator

    Model T753U - Teledyne Advanced Pollution Instrumentation

    The Model T753U is a portable, microprocessor based precision Calibrator for Ozone gas instruments and sensors. Using a sophisticated Ozone generation system, combined with a sensitive photometer and pneumatic design, the T753U produces stable and reliable concentrations of Ozone in a convenient and rugged package based on our popular T750/U Portable Multigas Calibrator platform. The T753U is housed in a high-density, molded travel case which includes an integral handle and wheels for durability and ease of use in the field for virtually any application. An internal zero air option extends the T753U's capabilities to also provide a clean and dry source of zero air, eliminating the need for a separate source of zero air. The internal zero air source module contains a software driven electronic inlet valve manifold allowing the calibrator to automatically switch between internal and external zero air sources depending on the application needs.The T753U operates in two modes; a high range, and a low range, or "fractional" mode, for producing accurate Ozone levels down to 2 ppb which meets the latest US EPA calibration requirements for Trace-level Ozone gas instruments. The mode is automatically selected based on the Ozone concentration range chosen by the user. To ensure high accuracy and stability of the Ozone output, the calibrator constantly measures the Ozone concentration being produced with an internal photometer and uses it to actively control the Ozone generator in real-time. The internal photometer can be certified by another external Reference Standard by simply using the 'photometer input loop' located beneath the fold up panel. The T753U Portable Ozone Calibrator combines performance and convenience for the most demanding applications.