Filter Results By:





detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers

Showing recent results 2161 - 2175 of 2398 products found.

  • PXI Resistor Module 4-Channel 1R to 63.7R with SPDT

    40-293-111 - Pickering Interfaces Ltd.

    The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications. The 40-293 can also be supplied with 8xSPDT electro-mechanical relays. These uncommitted relays have a number of uses, including extending the resistor chain, adding additional fault conditions and providing the functionally of a resistor module and an uncommitted relay module in a single PXIslot.

  • Simulating Optical Design Components

    Wave Optics Module - COMSOL, Inc.

    The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.

  • Single Electrode Dielectric/Conductivity Sensor

    Lambient Technologies

    Suitable for R&D, QA/QC and manufacturing applications with repetitiveoperations, the 8-mm dia. unsheathed and 0.5-inch dia. sheathed single electrode sensorsare designed for use in presses, molds or harsh environments where a tiny, reusabledielectric sensor is desired. They may be mounted so the electrode is flush with a platenor mold surface, insuring no interference with the flow of material during processing.These sensors are constructed with a stainless steel electrode embedded in a hightemperature polymer insulator. An optional thermocouple may be positioned in thesensor cable just behind the sensor head to allow approximate measurement of processtemperatures.

  • Software

    Electrochemistry Tests - Materials Development Corporation

    CyclicVoltammetry and Galvanostatic Charging are tests used throughout the industrial and scientific communities to study chemical reactions and behavior of electronic structures.  They are extremely helpful in the monitoring of nano based dielectrics, used in super /ultra capacitors or self-assembled monolayers (SAMs). The Cyclic Voltammetry test applies a ramping voltage to a device and measures the resulting current.  In acapacitor-like structure the current reveals loss in the dielectric as well as degradation over time.  CyclicVoltammetry is used to characterize the performance of supercapacitors and ultracapacitors formed using various nano-technologies.  It is also useful in the studies of self-assembled monolayers used for sensors.

  • TEV Antenna

    Techimp HQ S.r.L

    TEV sensor is a partial discharge sensor whose working principle is based on a direct Capacitive coupling with a Switchgears earthed metal case. The two ends of TEV sensor can be coupled magnetically to virtually any opening on a metal Surface. It picks up the electric signal given by PD activity onto the two metallic surfaces. Thanks to its special design has high sensitivity, larger than other single ended TEV sensors. His compact and robust design (passive sensor) makes the TEV the optimal sensor for direct installation on medium voltage Switchgears.

  • Thermistor Power Meter

    N432A and 432A - Keysight Technologies

    The 432A / N432A power meter is an automatic, self-balancing power meter for use with temperature compensated thermistor sensors. High efficiency and good radio frequency (RF) match are characteristics of the 478A and 8478B coaxial and 486 series (now discontinued) waveguide thermistor mounts that cover the frequency range 10 MHz to 40 GHz. Each thermistor mount contains data showing the calibration factor and effective efficiency at six frequencies, directly traceable to the U.S. National Institute of Standards and Technology (NIST) at those frequencies where NIST provides calibration service.

  • Thermostation

    VT-96 - Holding Informtest

    Thermal station VT-96 is intended for building data collection systems (distributed and remote) from thermocouple temperature sensors. The interfaces allow you to easily and quickly connect the VT-96 to a remote (via ETHERNET) or nearby computer (via USB). The integrated WEB-page provides a convenient way to check the communication with the unit and its functioning, and the standard VXIplug & play drivers reduce the costs of integrating the unit into the system and developing application software. Multiple thermostats easily integrate and synchronize with each other and other VXI instruments via a dedicated Trigger Bus.

  • VDT/Resolver Simulation Module for SLSC

    Bloomy Controls, Inc.

    Bloomy's VDT/Resolver Simulation Module offers eight channels of variable differential transformer (VDT) sensor simulation at an unmatched price point. Its highly-flexible nature allows each channel to be configured independently for simulation of a linear variable differential transformer (LVDT), a rotary variable differential transformer (RVDT), or a resolver. Versatile, separate E1 and E2 returns allow each channel to be connected in a 4-, 5- or 6-wire configuration. The included VeriStand SLSC driver also allows each channel to simulate two 4-wire sensors where shared excitation is acceptable.

  • Wireless Load and Force Measurement

    Wireless ELF - Tekscan, Inc.

    The Wireless ELF 2 System is a user-friendly, cost-effective load measurement system. This system combines 3 FlexiForce WB201 sensors, battery-operated WiFi transmitter (certified 802.11b radio- 802.11b/g/n compatible), and Windows-compatible software*, turning your PC or laptop into a force measurement instrument. The WELF2 system, sampling rates up to 200 Hz and comes in a high speed version with sampling rates up to 6,000 Hz. The WiFi connection setup has ad hoc and access point (unsecured router) network capability. For multi-handle use an unsecured router is required.

  • Exciting & Dynamic Robot Control Simulation Software


    EDRS is powerful simulation software that helps develop the intelligent robot and give the user training in convenient and speedy manner. Also, it comes with dynamic robot simulation based on three dimension andimplements minute performance control of the robot through Kinetic Engine.*Simulation in various types of environment by configuring the robot and environment in three-dimension*Configuration of the robot and environment by Robot Editor and Environment Editor*Various sensors essential for the robot and environment can be mounted and monitored at the user's choice*28 types of sensor for entering real life-like parameters and performing simulation*Capable of exporting and loading the robot, object and environment which the user has drawn using 3D Max(OPTION)*Possesses compiler itself and allows control of each robot sensor using C, C++ and Flow Chart Language and perform build and debug*Programming Library enables programming on Virtual C++(MFC) and Eclipse*Vision Sensor for viewing an object at the robot's point of view and observation at the user's and robot's point of view in separate windows*Realistic simulation using the Kinetic Engine for controlling the robot's complex and minute performances*Ehancement of educational effects with the Electronic Manual covering the robotics courses and over 20 types of flash animation for sensors and actuators*Real-time upgrade of a latest version through the software's Upgrade function on Internet

  • AViiVA SC2 4k Colour

    Teledyne e2v

    This member of the AVIIVA range of cameras features a 4K pixel colour sensor with a 10 micron pixel size and an RGB colour pattern (1365 x RGB pattern).This smarter camera supports both Camera Link, LVDS interface and is operable within a dynamic range of 8, 10 or 12 bits with dedicated electronics. With additional flat-field correction capabilities, contrast expansion functions, white balance and colour space correction, this camera is the perfect alternative for industrial applications requiring low-cost colour capture. Furthermore, one will avoid the usual problems observed with tri-linear sensors on optical alignment and object synchronisation.

  • CATx Surge Protector

    SP-CAT5-6V - Network Technologies Inc

    Protects sensors running on CATx unshielded twisted pair (UTP) cable against the effects of electrostatic discharge, faulty wiring and lightning. The use of two protectors on each end of the line will provide increased protection for each end against surges. Protected pins: (1,2) (3,6) (4,7) and (7,8) pass through. Impedance: 85 to 115 Ohms. Surge suppression: 22Vpeak @ 100A 10/1000µs. Maximum continuous voltage: 6Vpeak. Dimensions WxDxH: 1x3.6x0.9 in (25x91x23 mm). Regulatory approvals: GR 1089, NEC 800.100 and 830.100, ITU 703, UL94 V0 Flame Rated.

  • Data Acquisition & Telemetry Buoy System

    LOTUS - MacArtney A/S

    The MacArtney LOTUS buoy system consists of a spherical buoy corpus made from durable GRP, a turbidity sensor with antifouling wiper, a rechargeable battery pack and a data logger with integrated telemetry modem. The buoy is equipped with an “AQUAlogger 210 TYT” turbidity sensor provided with 4 measuring ranges selected automatically. To avoid biological growth on the optical window, the instrument is equipped with an antifouling wiper. The sensor is protected by a cage firmly attached to the buoyant body.The buoy and the data acquisition system has an open architecture that allows for integration of other types of sensors like CTDs, fluorometers, etc.

  • DC Power Supplies

    Tektronix, Inc.

    Single- and multiple-output power supplies for education, research, design, and automated testingPower levels up to 1080W with voltages up 10kV and currents up to 108ASpecialized battery-simulating power suppliesEquipped with advanced features, including current measurement with nanoamp resolution, variable rise/fall times, analog inputs, digital I/O, and programmable interfacesReady for today’s challenging applications:Power new components, circuits, and devices for design or automated testPerform breakdown tests on high power transistorsPower and test low power, portable, battery-operated products such as IoT devices, medical products, mobile phones, tablets, and remote industrial sensors

  • Digital Stik Liquid Level Sensor

    7250 - AMETEK Drexelbrook

    The 7250 Series digital stiks take field proven magnetostrictive sensing technology and packages it for greater reliability and easier installation. This liquid level sensor is ideal for liquid level monitoring, interface level and leak detection in a variety of liquid media in above ground and underground storage tanks. It was designed to meet EPA Leak Detection and API Inventory Monitoring requirements and has been approved for use in hazardous environments.The 7250 Series is series has an inherently lower cost design which results in savings. It provides the same performance and reliability as sensors that consume more power.