Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 2281 - 2295 of 2437 products found.

  • Industrial Calibrators

    Fluke Calibration

    A temperature calibrator, often called a thermometer calibrator, is used to correct inaccuracies in installed thermometers and temperature sensors, because temperature measurement is a critical parameter in many industrial processes. Although simulators are sometimes called temperature calibrators or thermometer calibrators and may be used to provide thermometer calibration for the electronics in an installed system, a temperature source with a calibrated reference sensor is still required to provide a complete and meaningful calibration. Fluke Calibration industrial and field temperature calibrators include: Metrology Wells; Field Metrology Wells; field dry-well calibrators; handheld dry block calibrators; Micro-Baths; large target infrared calibrators; field IR calibrators; ice-point dry-well; and thermocouple furnaces.

  • Isolated Process Control Signal Conditioning Products

    SCIM7B - Bee Instruments

    SCIM7B Isolated Process Control Signal Conditioning Modules provide a complete selection of backpanels DIN rail mounting accessories, interface cables and rack mounting hardware.Each SCIM7B module provides a single of isolated analog input or output. Various input modules accept analog voltage or current signals from all types of field sensors and sources, filter, isolateamplify, linearize and convert these input signals to high-level analog outputs suitable for use in a process control system. Output modules accept high-level analog voltage signals from a process control system, then buffer, isolate, filter, convert and amplify before providing a current or voltage output to a fielddevice.

  • Magcam MiniCube1D

    MagCam NV

    Magcam's MiniCube1Dmagnetic field camera provides quantitativeBz magnetic field mapping in a 12.7mm x 12.7mm 2D planewith 0.1mm spatial resolution, measured at high speed. The camera is based on Magcam's unique integrated 2D Hall sensor array technology, featuring more than 16000 microscopic magnetic field sensors on one single chip. Each sensor independently measures the local magnetic field, resulting in quantitative2D magnetic field maps with high spatial resolution, measured athigh speed. These magnetic field maps contain a large amount of information about the magnet's properties, which can be extracted using Magcam's powerful MagScope measurement and analysis software.

  • NFC Sensor Interface for Industrial IoT

    AS3956 - AMS Technologies AG

    AS3956 Dynamic NFC Sensor Tag IC meets industrial-grade quality standards and provides very high reliability in mission-critical applications and in end products with a long operating lifetime. AS3956 offers standalone NFC passive tag functionality in a small form factor. The AS3956 dynamic tag acts as a contactless bridge between sensors and any NFC reader, such as a smartphone, through a host microcontroller. Fast system integration and high speed data transfer are guaranteed by the available SPI and I²C interfaces and optimized protocols (Tunneling mode and Extended mode), allowing bidirectional communication between the device microcontroller and an external NFC compliant device or ISO14443A reader device.

  • Optical Rotary Encoders

    BEI Industrial Encoders

    Optical sensing technology is the most precise and offers the highest resolution of the position sensing technologies. Rugged construction and years of field proven service makes BEI optical rotary encoders ideal for operating in harsh industrial environments including oil well drilling, machine control, agricultural machinery, web process control, robotics, elevators, construction equipment, cranes, motor feedback and any closed loop control systems. BEI optical encoders are available as incremental, absolute single-turn, and absolute multi-turn. BEI Sensors programmable encoders offer resolution flexibility to match changing needs while also saving on inventory costs and reducing machine downtime.

  • Sensor for Filament Inspection

    EyeFI - Eye Vision Technology GmbH

    EVT presents the EyeFI - the sensor for the inspection of filaments. The sensor contains two cameras with an Aptina sensor and S-Mount lenses. The cameras are perpendicular to each other. It is therefore possible to inspect two sides of the filament, which means that the EyeFI can detect if the filament is out-of-roundness. Additionally the errors and defects can be detected. For example the occurring flaws are point-shaped or partly flaked, or point-shaped and transverse, or also looking like a longitudial rib, or only spots in different shapes. The defects can be detected with the EyeFI sensor. The EyeFI contains board cameras with sensors from Aptina, the IoCap and an evaluation processor. The housing is about 14x10x4 cm in size. The IoCap is the image-capture-IO-board, which is designed and developped by EVT.

  • Specialized Gateways

    B+B SmartWorx

    The SmartSwarm 341 IIoT gateway enables owners, operators, and integrators of remote assets to integrate data from the asset into IIoT applications such as dashboarding, analytics or predictive maintenance. Data can be collected from a number of sources, including web feeds, databases and files, as well as from locally connected physical devices and sensors. SmartSwarm 341 also includes an interface and manager for B Bs Wzzard wireless sensor platform providing robust acquisition and transmission of asset sensor data without the expense or time involved in installing cables. For bulk I/O requirements where cabling is not an issue, it is also compatible with WISE and ADAM Ethernet connected I/O modules

  • Virtual Receiver/Exciter Generalized Simulator

    VREX - FishEye Software, Inc.

    Electromagnetic sensors include a “front-end” that generates and receives the electromagnetic waves through a subsystem known as a Receiver/EXciter (REX). They also include a “back-end” that performs signal and data processing, typically implemented in software. These separate subsystems must be designed and developed separately, then integrated together. The development of the overall sensor is slowed and complicated by the problems that show up for the first time at integration testing. This is due in large part to the interdependencies of these subsystems that cannot be effectively tested during development. Later, software patches, configuration upgrades, waveform changes, and technology refresh become substantially more expensive because they can only be verified by traveling to the operational site to connect with the actual front-end hardware.

  • Wireless Temperature And Humidity Data Logger

    ThermaSense - McGan Technology

    ThermaSense is a Wireless temperature and humidity sensor with external humidity and RTD based temperature sensors, the device provides a fast response time for both parameters, Functions include starting, stopping and downloading from the device wirelessly. Data can be provided in real time back to a central PC, or the device may be downloaded at periodic intervals. The digital display provides the current reading for both the humidity and temperature levels with a quick view of minimum, maximum and average statistics of the logged data. An audible buzzer and LED alarm indicator alarms when either parameter is above or below the threshold set. Email and text alarms can also be configured and sent from within the software.

  • X-RAY Cameras Based On CCD

    XiRAY - XIMEA GmbH

    *High resolution direct phosphor imaging, ideal for Micro CT*Ultra-low readout noise with CCD and especially the new sCMOS sensors*Crystal clear 14 bit/pixel images*Partial readout and binning modes for enhanced sensitivity and higher speed*Non-linearity over full dynamic range <2% (of full scale) to 95% of full scale*External triggering, LVTTL*Low power consumption 6 Watt with Cooling or 2W without*Antiblooming, Enhanced Statistical Extra-Mural Absorption*Radiation hardened, Support of Energy levels 7 to 100keV*Measures just 63 x 63 x 46 mm*Peltier TE Cooled with Heatsink and optional fan

  • Amplified Torque & Load Cell Indicator

    9834 - Interface Inc.

    For use with amplified load cells and rotary torque sensors. Features 120 readings per second, programmable +/-10V or 4-20mA analog output, peak and valley monitoring, RS232. Packaged in an aluminum 1/8 DIN, panel mountable enclosure with a plug-in AC power cord. Sensor connection via 9-pin connector.

  • Machine Vision Lens

    FUJINON HF6XA-5M - FujiFilm Corp.

    This new product, which has an external diameter of 39 mm and a focal length of 6 mm, is the world's smallest* Machine Vision lens which is used for industrial processes such as product inspection and measurement on production lines. HF6XA is a new lens which is designed for compatibility with 2/3" sensors with a pixel pitch of 3.45m (five megapixels). HF6XA is a FUJINON Machine Vision lens designed for compatibility with 2/3" sensors, which has coverage of approximately twice*** the current product, the FUJINON HF8XA, which offers the widest coverage range. In the frequently used environments of customers, the lens is compatible with the ultra-high resolution of 3.45m pixel pitch (equivalent to five megapixels when using a 2/3" sensor) under a large portion of the screen. Furthermore, for a wide range of installations and shooting conditions, the lens boasts "4D High Resolution"*4 performance, mitigating resolution degradation that typically occurs when changing a shooting distance or aperture value and maintaining a high level of even image sharpness across the entire image area at the ultra-high resolution of 4.4m pixel pitch (equivalent to three megapixels when using a 2/3" sensor). Despite being a wide-angle 6mm lens, the lens achieves the world's smallest external diameter of just 39 mm. The lens is ideal for attachment inside compact inspection devices with restricted internal space when wide coverage and consistency is required for reading product codes and serial numbers or for inspecting product shape and appearance.

  • Resilient Modulus and Asphalt Testing System

    Atico Export

    The Resilient Modulus software features built and test sequences, and the capability to specify user defined sequences. Contact stress is automatically adjusted according to the above procedures as selected. Available waveforms include haver sine, sine, square and triangular, along with a user defined waveform selection. Optional peak & valley compensation ensures proper and quick matching of the load parameters. Real time displays of the prescribed versus actual dynamic load or the dynamic deformation measurements by each sensor are always present. Deformation ratio of the two sensors, Rv (to ensure that the two deformation sensors are in agreement) and  Mr are also calculated in real time. During export, curve fitting is done to fit the results to models that predict Mr as a function of σm, σd, and CP (cell pressure). Four different functions are calculated automatically

  • Analysis Tool for ECU Networks and Distributed Systems

    CANape - Vector Informatik GmbH

    The primary application area of CANape is in optimizing parameterization (calibration) of electronic control units. During a measurement process, you can simultaneously calibrate parameters and record signals. The communication between CANape and the ECUs takes place via protocols such as XCP or via microcontroller-specific interfaces with the VX1000 measurement and calibration hardware. CANape supports various ADAS sensors such as radar, LIDAR and video. Combined with high-performance hardware, CANape can store multiple gigabytes of data per second. Calibration data management and convenient measurement data evaluation including data management as well as reporting make CANape a complete tool for ECU calibration. Of course, CANape also provides access to bus data, diagnostic data and analog measurement data.

  • Combination Board Tester

    Qmax Test Technologies Pvt. Ltd.

    Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.