Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 2371 - 2385 of 2437 products found.

  • 10 MHz to 6 GHz USB Wide Dynamic Range Average Power Sensor

    U2041XA - Keysight Technologies

    Accurately measure any modulated signal with the Keysight Technologies, Inc. U2040 X-Series wide dynamic range power sensors. The USB connectivity models come with world's widest dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U2040 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.

  • Doppler Current Profiler

    SeaGuardII DCP - Aanderaa Data Instruments AS

    It features innovative development of the acoustic profiling capacity and an exceptional ability to collect high quality current information on moving and tilting moorings. Available as a self-recording instrument, it also integrates unique real time features to meet your application needs. The SeaGuardII is a smart data hub that combines the SeaGuard electronics with the advanced management firmware of Aanderaa SmartGuard data hub. SeaGuardII DCP is a 600kHz frequency profiler with multi-sensor capability. By design, we offer increased deployment time, optimized configuration flexibility and unique features to cope with demanding upper ocean environments. Optional parameters are available using Aanderaa range of smart sensors that include temperature, pressure, conductivity, oxygen, wave, tide and turbidity. In addition the SeaGuardII has 4 analog inputs, 2 serial ports with power control and direct connection for real time data transmission unit.

  • Force Balance Inclinometers

    Columbia Research Laboratories

    Columbia's SI-701 Series of Inclinometers are electronic tilt sensors based on Force Balance Accelerometer technology. They produce high level low impedance output proportional to the sine of the tilt angle. Model SI-701B is a low cost general purpose sensor that can be up-graded with the addition of the Columbia "HP" torquer system (SI-701BI) for greater accuracy and ruggedness. A bi-axial version of both units (SI-702B) is also available. The Model SI-701BI is designed with an output circuit made for 4-20mA data transmission systems for industrial applications. The model SI-701FND is a fluid dampened premium performance inclinometer designed to produce accurate tilt data in extreme shock and vibration environments. The latest addition in the line is Model SI-701WPBI, a waterproof (to 150 feet) inclinometer which operates from a +15 volt supply with 4-20mA output. A single power supply powers both the sensor and the 4-20mA line driver.

  • New Link system Control and Image Capture Software

    Linkam Scientific Instruments

    New uncluttered and intuitive user interfaceLive display of current status for easy monitoringFull control of heating and cooling rate, limit and hold time of up to 100 rampsRow by Row control of Vacuum, Humidity, Tensile Force and Shear modes controllable and synchronised with TemperatureParameters of connected Linkam sensors displayed and stored - e.g. Vacuum, Humidity, Force, XY position and Pressure (dependent on connected stage type)Real Time chart of temperature and other measured parametersTrigger I/O for synchronisation with other equipmentTriggers recorded and plotted row by rowAutomatic setup of controls and parameter limits based on stage type connectedFull five point temperature calibrationUSB 2.0 to T96 and CSS450 ControllersOptional modules including Linkam Imaging Systems with high performance camerasIncludes .NET Components for easy integration into 3rd party applications e.g. LabViewNative 64 bit application

  • SMART III RF Probe

    Finna Sensors

    Finna Sensors’ Smart III RF Moisture Probe is appropriate in those situations where NIR use on conveying systems/web applications or RF flat plate sensor use on board type products are not sufficient. Examples include tanks, bins, barrels, drums, Super Sacks™, silos, etc. These applications require a probe type moisture meter where the probe is inserted into, and is surrounded by product. Since the probe generates a 3 inch diameter radio frequency field around the length of the probe, a significant volume of product is measured. As the product is slowly removed from the silo, and refilled from the top, it passes by the RF Probe, thereby providing a constant real time moisture measurement. Typical applications would include starches, distillers and brewers grains, granulated chemicals or food ingredients, whole grains such as corn kernels, rice, soybeans, tree nut stockpiles, etc.

  • Test Pattern Generator Delay & AV Sync Analyzer

    VQDM-100 - VideoQ Inc

    Versatile compact and robust multi-purpose tool for R&D and glass-to-glass QA/QC Instant visual-aural quality estimation plus automatic latency, AV sync and 3D LR sync measurement Multi-channel time-line analysis, including video frames continuity testing 4 Light Sensors with vacuum caps, 4 Audio inputs (standard line levels) 2 channels of AV timing analysis, simultaneous measurements of Video and Audio Latencies Real time multi-channel data acquisition via USB port Unique sophisticated set of static and dynamic test patterns up to 1080p@60fps - see more details in separate VQL page Source of VQDM, VQMA2, and VQMA3 Test Patterns for VideoQ Analyzers Multi-format digital and analog AV outputs: HDMI, YPrPb, S-video, SPDIF, LR analog audio Networkable unit, easy expansion with any external USB storage device: live clips, user content, etc.

  • VIS-NIR Cameras

    Inframet

    Surveillance cameras based on CCD/CMOS/ ICCD/ EMCCD/EBAPS imaging sensors sensitive in visible and near infrared range are widely used in many long range surveillance applications as independent imagers or as part of a bigger multi-sensor surveillance systems. Majority of VIS-NIR cameras are used for day level applications but an increasing number of these cameras is used to enable surveillance in both night and day conditions. In both cases it is important to verify performance of these cameras under varying illumination conditions from very dark nights to ultra bright days. Important missions can fail due to too low sensitivity of VIS-NIR cameras at night conditions (dark, noisy images) or due to too low dynamic at ultra bright day conditions (saturated, blurred images). Next, it is important to use VIS-NIR cameras that generate high quality images in order to achieve maximal effective surveillance ranges.

  • Load Cell

    Futek Advanced Sensor Technology, Inc.

    Load Cells manufactured in US by FUTEK Advanced Sensor Technology (FUTEK), a leading manufacturer producing a huge selection of Load Cells, utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.A Load Cell is defined as a transducer that converts an input mechanical force into an electrical output signal. Load Cells are also commonly known as Load Transducers or Load Sensors.

  • 10 MHz to 6 GHz USB Peak and Average Power Sensor

    U2042XA - Keysight Technologies

    Accurately measure any modulated signal with the Keysight Technologies, Inc. U2040 X-Series wide dynamic range power sensors. The USB connectivity models come with world's widest dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U2040 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform complex pulse analysis and standard average power measurement.

  • 2-Channel Front End

    BEQ II.1 - HEAD acoustics GmbH

    *Binaural, digital equalizer with 24 bit technology and USB interface.*The digital equalizer BEQ II.1 combines the characteristics of an equalizer, a two-channel front end and an A/D converter into one mobile and very versatile measurement tool.*Binaural, aurally-accurate recordings can be conducted easily with BEQ II. The AES/EBU interface allows a quick and easy expansion into a four-channel system, e.g. with the HMS III or HMS IV. Via the ADAT interface, up to four BEQ II units can be connected, allowing for eight-channel recordings.*Integrated signal conditioning allows common measurement sensors (Microphone, Line, ICP�) to be directly connected to the front end. In addition, separate pulse inputs are available e.g. for RPM data acquisition.*Thanks to the high-performance built-in battery - external DC power supply is also possible - and its low weight, BEQ II.1 is the ideal tool for either mobile or stationary operation.

  • Area Scan Cameras

    ace Series - Basler Vision Components AG

    Enjoy a new class of digital cameras that will help you to be even more successful and efficient at what you do. High quality and performance levels combined with a low starting list price of only 199 and a small 29 mm x 29 mm housing make Basler ace cameras one of the world''''s best-selling cameras with thousands of satisfied customers. It is available with several resolutions and speeds and with sensors from all leading manufacturers so that you can easily find the right ace camera model for your application. Choose from the most popular and standard proven data interfaces in the vision market: With the ace Gigabit Ethernet models, you benefit from our GigE market leadership, easy multi-camera setups and 100-meter cable length. Camera Link is the interface for high image data transfer. And with USB 3.0 there is an interface technology which is easy to use and real-time capable.

  • Dual Non-Contact Infrared Thermometer

    OS768-LS - Omega Engineering, Inc

    OMEGA's OS768-LS is the ultimate tool for temperature measurement. Accurately verify surface temperatures with two of the most reliable temperature sensors:* Non-contact micro-machined thermopile* Type K thermocouple input (free T/C included)Such an arrangement can fulfill most temperature measurement requirements. The non-contact infrared measurement is ideal for non-reachable situations, due to safety or sanitary reasonsinstant readings, safely and reliably. Or use the thermocouple for high precision measurement of contact surfaces, gases, and liquids. The OS768-LS can also help measure emissivity, which is often difficult for a user to determine. Use the Type K thermocouple contact to measure the true temperature. Then, use the non-contact infrared to get the surface temperature. Adjust the emissivity until they are the same, with the option to use the same emissivity setting for that object next time. No more guess work, no more looking up on Emissivity Table. This unit also comes with an ultra-long battery life (batteries are included).

  • Infrared Thermometer

    DITH 120 - Desco

    Infrared Thermometer is also known as laser thermometerInfrared thermometer is a thermometer which infers temperature from a portion of the thermal radiation sometimes called blackbody radiation emitted by the object being measured.Laser is used to help aim the thermometer or non-contact thermometers or temperature guns, to describe the device's ability to measure temperature from a distance. By knowing the amount of infrared energy emitted by the object and its emissivity, the object's temperature can often be determined. Infrared thermometers are a subset of devices known as "thermal radiation thermometers".The design essentially consists of a lens to focus the infrared thermal radiation on to a detector, which converts the radiant power to an electrical signal that can be displayed in units of temperature after being compensated for ambient temperature. This permits temperature measurement from a distance without contact with the object to be measured. A non-contact infrared thermometer is useful for measuring temperature under circumstances where thermocouples or other probe-type sensors cannot be used or do not produce accurate data for a variety of reasons.

  • Magnetoresistive Milligauss Meter

    MR3 - Alpha Lab, Inc.

    The MR3 Magnetoresistive Milligauss Meter measures and displays the three vectorcomponents (X, Y, Z) as well as the magnitude (M) of the static magnetic field. Update is two times per second. The three sensors are in a 25 mm (1") cube at the end of a flexible 100 cm (40") cable. It can be powered by 4 AA batteries (included) or a Worldwide AC adaptor (included). It can collect and store data (X, Y, Z and M) for later download or stream data live via USB connector. Both the instantaneous values of X, Y, Z and M, and their peak values, are displayed on the meter screen. "Peak" values are the highest values seen since the peak reset button was pressed. Maximum error of sensitivity is +/- 0.5 % of the reading, and the maximum error of the offset is +/- 0.50 milligauss. Range is +/- 1999.99 milligauss with resolution 0.01 milligauss (or 1 nT) over the full range, displayed simultaneously for X, Y, Z and M.

  • Non Contact Torque Transducers

    RS425 - Datum Electronics

    The Datum Electronics Series RS425 non-contact rotary torque transducers have been designed to fit easily in line with any drivetrain or test bed using either a spline or keyway shaft. We are able to modify the ends of the transducer to best suit your requirements, and can even design bespoke ends to fit. This type of transducer has many advantages over other torque systems including: zero bearing friction, high speed and high torque applications. The RS425 torque transducer utilises a strain gauged shaft for accurate and reliable torque measurement and a set of rotating on shaft conditioning electronics, the digital signals are transmitted to the non-rotating part of the system or stator providing a reliable and highly accurate torque measurement solution. The rotor is continuously powered enabling static torque measurement to be made. Not only does the RS425 Series offer great technical advantages but the range of torque sensors are competitively priced.