Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
product
CAN Sensor/ Interface
Current
Reach Technologies’ CAN Current Sensors sense and digitize conductor current for collection via CAN. The module is ideal for conveniently adding current data to a distributed CAN network. The CAN Current Sensor is configurable via J1939 or CANopen stacks, and are available in Hall Effect and shunt variants.
-
product
Capacitance Sensor Systems
MTI Instruments offers high resolution capacitance sensors, probes and systems that generate low noise, highly accurate and high stable measurements. Our Capacitance sensor line-up offers accurate measurements for automated inspection applications such as thread quality inspection, disk drive run-out, leveling or flatness measurement, lens alignment, tire run-out and bulging. Our Accumeasure capacitive sensors offer large stand-off distance that includes single and multiple channel rack systems ...show more -
product
Capacitance Simulation Card
SET-1220
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.
-
product
Carbon Dioxide Gas Measurements
LI-830 And LI-850
Some CO2 sensors are too simple. Other CO2 analyzers are costly and complex. But the LI-830 and LI-850 are just right – bringing proven performance at an economical price to provide CO2 gas measurements that you can depend on day after day.
-
product
Carbon Monoxide Detectors
Inspector CO Detectors
Sensorcon, Sensing Solutions by Molex believes in the importance of a dependable gas detector. Featuring proprietary engineering & software, our Inspector Series utilizes electrochemical sensors for fast & accurate measurements of CO.
-
product
Carbon Sensor Conductivity Meter
HE-960LC
Can measures conductivity of low concentration. Its dual calculation circuits and software, combined with carbon sensors, enable measurements ranging without switching. The HE-960LC can be used as a process concentration meter, and also to monitor changes in the concentration of specified chemicals.
-
product
Carbon Sensor Conductivity Meter High-Concentration
HE-960HC
FPD manufacturing processesThe HE-960HC measures conductivity, which forms the basis for parameters in chemical and waste water management. Its dual calculation circuits and software, combined with carbon sensors, enable measurements ranging without switching. The HE-960HC can be used as a process concentration meter, and also to monitor changes in the concentration of specified chemicals.
-
product
Carbon Sensor Conductivity Meter (Low concentration type)
HE-480C-GC
The length of the sensor has been reduced by 50% as compared to existing systems to reduce space requirements. At the same time, the measurement range has been increased tenfold, enabling the system to measure even samples with comparatively high concentrations. Two different types of chemicalresistant glassy carbon sensors can be used, making the system ideal for chemical dilution/recovery management and pure water recycling as well.
-
product
CATx Surge Protector
SP-CAT5-6V
Protects sensors running on CATx unshielded twisted pair (UTP) cable against the effects of electrostatic discharge, faulty wiring and lightning. The use of two protectors on each end of the line will provide increased protection for each end against surges. Protected pins: (1,2) (3,6) (4,7) and (7,8) pass through. Impedance: 85 to 115 Ohms. Surge suppression: 22Vpeak @ 100A 10/1000µs. Maximum continuous voltage: 6Vpeak. Dimensions WxDxH: 1x3.6x0.9 in (25x91x23 mm). Regulatory approvals: GR 1089, NEC 800.100 and 830.100, ITU 703, UL94 V0 Flame Rated.
-
product
CCD Foundry Services
Teledyne DALSA Semiconductor’s 150mm CCD process offers surface or buried channel operation at up to 15V with two or three layers of polysilicon and one, two or three layers of metal. A modular processing approach allows our foundry customers to adjust process parameters to meet the most demanding requirements for CTE (>99.999%), charge storage capacity, and dark current (<1nA/cm2). The base process uses 1X projection lithography with 2.5µm design rules, allowing die sizes of up to 100mm X...show more -
product
Centor Dual R, 2 channels force gauge, external load cell
CNR DLR
The force gauge Centor Dual R series have all the functions of a Centor STAR R force gauge. And thanks to its ability to read two sensors simultaneously with a 500 Hertz sampling rate per channel, the force gauge Centor Dual is a true test console. It offers all of the functionality of an efficient force gauge, its calculating power enables it to save values from two different sensors simultaneously, to monitor set points and to perform calculations on each channel.
-
product
CGS500-IR NDIR Gas Sensor
The CGS500-IR sensor is a NDIR (non-dispersive infrared) sensor designed to replace thermocatalytic gas sensors for monitoring hydrocarbon gases in the range 0-100% LEL. The CGS500-IR is available as a sensor only or fitted in an EEx e certified junction box.
-
product
Charge Amplifiers & Signal Conditioning
The use of charge amplifiers alongside piezoelectric charge output sensors is still widespread in many industries. This is due to the rugged and high temperature capabilities of the sensors. There are many challenges in using these sensors and it needs a good understanding of the technology to get a quality, noise free signal for accurate data.
-
product
Chassis Ride Height Applications
Chassis height sensing is a specific application of CTS' rotary sensor technology. Chassis height sensors measure the position of the control arms relative to the frame or body of the vehicle. This information is used in systems such as headlight leveling and real-time-dampening. Key features of the CTS' chassis height sensors is the ability to mount in a variety of angles and projections to accommodate difficult packaging as well as robust sealing required for under chassis applications. With a global team of application engineers, CTS can package one of our generic, tooled for sales sensors or develop a custom product, unique for your application.
-
product
Chilled Mirror Hygrometer
DewMaster
One, two or three stage sensors available - integral or remote from controller.NIST traceable calibration certificate.Depression range choice of either 45, 65 or 95°C . (one, two or three-stage cooling)Automatic Balance Control (ABC)
-
product
ChromaLine Sensor
MPLS-DM
Sciences et Techniques Industrielles de la Lumière
Based on STIL's chromatic confocal technology, ChromaLine sensor family represents the next step in industrial integration.Thanks to its accuracy, its robustness and a life span of several years without any maintenance, MPLS sensors are adapted to the requirements of on-line control.
-
product
Clamp Meters
TES Electrical Electronic Corp.
Variable Frequency drive measurement. LoZ voltage measurement to drain ghost voltages. Check 3phase sequence. True RMS reading on AC and DC+AC mode. Inrush current measurement. A measurement for HAVAC flam sensors.
-
product
Click Boards
Click Boards for Wireless Connectivity, Sensors, Interface, Display & LED, Mixed Signal, Storage, Motor Control, Audio & Voice, HMI, Clock & Timing, Power Management, & more.
-
product
Climate Chamber
ICH
Its excellent temperature and humidity homogeneity positions the climate chamber ICH in the international top league of stability test chambers. Thermal transfer to the interior whether heat or cold is guaranteed through a large-area air jacket on four sides. Thanks to its hermetically sealed interior, the climate chamber ICH does not consume any water once the setpoints have been reached, provided that the door is not opened. Two high-grade platinum temperature sensors with mutual monitoring guarantee interruption-free long-term operation even if one sensor should fail.
-
product
Clock Drivers
Multiple timing signals ("clocks") are required by CCDs, IR FPAs, and some CMOS image sensors to transport electrical charge across the array to a sense amplifier for conversion into image data. Pulse Instruments offers a line of "clock drivers" for generating these timing signals. The parameters of these clocks (clock rate, pulse width, pulse amplitude, rise- and fall-times, etc.) greatly influence the behavior and performance of the imaging device. Our products take logic-level inputs from a p...show more -
product
Closed-Loop Motor Controller
MS320
Master and Ratio-Follower modes and programmable input functions. Options include analog speed feedback input, analog setpoint inputs and relay outputs. Works with incremental shaft encoders and pulsefrequency output shaft speed sensors. Optional explosion proof enclosure or NEMA 4X enclosure kit.
-
product
CMOS Cameras
Magic series
New Imaging Technologies proposes a broad range of visible products. From sensors to complete camera systems, all of our products integrate our unique NATIVE WDR capabilities. Our NATIVE WDR™ is a new generation of CMOS imaging technology named MAGIC™ (standing in english for Active Matrix with indexed generated contrast ), capable of generating a highly stable image even under very wide intra scene dynamic range (> 120dB) in a single frame time and without multi-exposure, any setting of knee points or external control. Our products are suited for many demanding applications and industries.
-
product
CMOS Image Sensor
CIS
CMOS Image Sensors (CIS) allow multiple camera functions in mobile devices, automobiles and security systems. Nidec SV Probe provides both standard and advanced versions of our CIS cards employing a wide variety of materials ensuring a durable cost-saving solution that can meet the fine pitch and multi-dut challenges of these devices. Other features and benefits include: • Proprietary AC™ Alloy Probes • Reduced Damage Under the Pad • High Frequency Capability • Better Alignment S...show more -
product
CMUT Evaluation-Kit
The "CEK CMUT" evaluation kit offers interested developers of ultrasonic sensors and users the opportunity to set up a fully functional test setup for evaluating miniaturized capacitive micromechanical ultrasonic transducers (CMUT). It consists of either one or two CMUT sensor modules, adapted control electronics and software as a web application that controls the CMUT via plug-and-play.
-
product
Coaxial Dual-Directional Coupler, 2 GHz to 18 GHz
772D
The Keysight 772D is a high-performance, dual-directional coupler designed for broadband swept measurements in the 2 to 18 GHz range. This coupler can be combined with Keysight power sensors and power meters for reflectometer applications. Forward and reverse power measurements on transmitters, components, or other broadband systems are made simpler using the Keysight 772D. The broadband design allows the use of a single test setup and calibration for tests spanning the entire 2 to 18 GHz range.
-
product
Collision avoidance systems with radar
With OndoSense radar sensors for collision avoidance, obstacle detection and positioning, you ensure safe, accident-free and productive vehicle operations. Our robust anti-collision sensor is suitable for trucks, mobile robots, drones, ships, aircraft or other vehicles and detects obstacles with great reliability.
-
product
Color Mark
Accurately detect color variations using our powerful color mark sensors that provide reliable data transmission via IO-Link.
-
product
Color Sensor
The color sensor product family includes both RGB (Red, Green, Blue) and high-accuracy XYZ light sensors for precise color measurement, determination, and discrimination. XYZ sensors are capable of providing xy chromaticity co-ordinates in accordance with the CIE 1931 color map. The ams color sensors include filters to block unwanted IR light in the visible spectral range, enabling highly accurate color measurement. Their high sensitivity coupled with their wide dynamic range make them well suit...show more -
product
Color Sensor & Proximity Detection
The ams family of color and Ambient Light Sensing (ALS) sensors combined with proximity detection provides red, green, blue, and clear (RGBC) or green and clear (ALS) light sensing and proximity detection. These modules also contain an IR LED for the proximity function. Both the light and proximity sensing functions feature high sensitivity and a wide dynamic range, so these devices may be placed behind the dark bezels of smartphones, monitors, laptops and TVs.
-
product
COLOSUS
The COLOSUS line of electro-optical test systems from Santa Barbara Infrared Inc. and Labsphere Inc. include collimated optics, software and uniform sources for the optical characterization of sensors and cameras.