Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 1246 - 1260 of 2247 products found.

  • PXI Precision Resistor Module 6-Channel, 3 to 1.51M

    40-297-050 - Pickering Interfaces Ltd.

    A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.

  • Finline Detectors

    950 Series - Milimeter Wave Products, Inc.

    Mi-Wave’s 950 Series Detectors convert incident RF energy into a DC voltage signal. The function of these detectors is similar to power sensors, with two exceptions. The 950 Series detectors perform measurementsmore quickly and have a greater dynamic range than that obtainable from comparable power sensors.

  • Bi-Directional Level Translator

    IFB-10001 - Playing With Fusion Inc

    Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.

  • Ruby 1.3M

    EV76C660 - Teledyne e2v

    The EV76C660 and EV76C661 are the newest members of Teledyne e2v’s Ruby family of CMOS imaging sensors. These breakthrough devices provide sensitivity and performance beyond that considered possible on a front side illuminated sensor with a pixel size of 5.3μm, Quantum Efficiency (QE) of over 80% and excellent sensitivity and performance in the near-infrared (NIR) spectrum (>50% at 850nm). This significantly reduces system illumination costs, or enables very low-light imaging in outdoor camera applications. The EV76C660 and EV76C661 share the same package, pin-out and software interface as Teledyne e2v’s Sapphire family of imaging sensors, enabling them to provide a range of differentiated industrial camera products from a single hardware and software development effort.

  • Socket Wrench Torque Sensor Rotating Type

    RSS SERIES - Transducer Techniques, Inc

    Our RSS Series rotating socket wrench torque sensors are available in ranges from 10 ft-lbs. through 250 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. Unlimited rotation of the ball bearing supported sensor shaft allows monitoring of the total fastening cycle. The sensing element incorporates bonded foil strain gages of the highest quality, along with coined silver slip rings and two silver graphite brushes per ring for data transmission.

  • Counters and Timers

    Orbit Controls AG

    Counters and Timers from Orbit Controls are designed for a direct connection to nearly all industrial sensors and pulse sources. They can operate as process monitors to display the input signals, or as process controllers with control outputs. The counters measure and display frequen frequencies or pulses from single sources, quadrature sensors or absolute coded Gray or binary resolvers. Apart of the calculated display the counters generate analog outputs, serial or parallel data ports and control set points. The parameters are entered via the keyboard in order to display the process in the required units and optimize the serial data, the analog outputs and the set points.

  • Grid Analytics System

    Sentient Energy, Inc.

    Sentient Energy’s Grid Analytics System consists of intelligent sensors, distributed apps and the Ample Analytics suite. Sentient’s flagship, the MM3™, is an intelligent oscilloscope with high-performance sensors featuring substation-class measurement, computing and processing capabilities. Much like modern smart phones, Sentient MM3s can accept new apps downloaded over-the-air and be configured to meet the utility’s evolving needs. MM3s locally capture and process detailed data at many points along the network and communicate specific alerts and analyses to SCADA or Ample™ Analytics modules for feeder or system wide studies.

  • Device Current Waveform Analyzers

    Keysight Technologies

    The dedicated Current Sensors measure from 100 pA level dynamic current up to 10 A with a maximum of 200 MHz bandwidth. The mainframe acquires the signal from the sensors by a maximum of 1 GSa/s sampling speed and 14-bit and 16-bit wide dynamic range. This combination allows you to measure quite wide range of dynamic current, for example, from standby/sleep state to active state, at a single measurement. In addition, the wide bandwidth and the high speed acquisition enable you to measure high speed pulse response even less than 100 ns previously very difficult with existing instruments.

  • Environmental Wafer Level Test Handler

    Aiolos - Afore

    Wafer level test handler for environmental sensors with with physical stimulus Vacuum probing, pressure probing, gas probing, humidity probing - AIOLOS is solution for these and much more. VVery high UPH capacity and the lowest cost of test (COT)AIOLOS has a unique automatic precision wafer prober placed inside chamber. Vacuum, pressure, humidity or gas stimulus is applied to whole wafer and wafer can be probed in stabile environment. Closed chamber with controlled humidity is perfect solution for temperature probing and lightless chamber can be utilized in testing of photonics in wafer level.AIOLOS is a solution for wafer level testing of pressure and environmental sensors, on bare wafer or on blue tape after dicing.

  • EPM Series Dual-Channel Power Meter

    N1914A - Keysight Technologies

    Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivityCode-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hostsAutomated frequency/power sweep measurements with the optional external trigger in/out feature

  • EPM Series Single-Channel Power Meter

    N1913A - Keysight Technologies

    Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivityCode-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hostsAutomated frequency/power sweep measurements with the optional external trigger in/out feature

  • Multi-Parameter Controller

    8900 - Georg Fischer Signet

    The Signet 8900 Multi-Parameter Controller takes the concept of modularity to the extreme. Each 8900 Controller is field-commissioned with the users-specified combination of inputs, outputs, and relays using simple-to-install modular boards into the base unit. Configure the system by selecting either two, four, or six input channels which accepts any of the Signet sensors listed below, and/or other manufacturer's sensors via a 4 to 20 mA signal converter (Signet Model 8058). To complete your unit, choose a power module with universal AC line voltage or 12 to 24 VDC.

  • Multi-sensor Drug & Explosive Detection System

    HDK - Laser-Detect Systems Ltd.

    LDS Hybrid Detection Kit (HDK) - By operating the sensors in parallel, and in real-time, results in much higher probability of detection than the performance of each specific detector. Integrated solution including laser detection technologies, dual Ion Mobility Spectroscopy (IMS) and chemical detection, that operate in synch. The HDK employs a proprietary algorithm to processes the feeds from each of the detectors. Operating the sensors in parallel, and in real-time, results in a much higher probability of detection than the performance of each specific detector. HDK also provides much lower false positive rate, even in conditions that hinder detection by each of the specific techniques.

  • MWIR Systems

    L-3 Cincinnati Electronics

    L3 Cincinnati Electronics’ high-performance cooled mid-wave (3.5 – 5.0 µm) IR imagers are based on our patented InSb focal plane array architecture. Ideal for all combat conditions, L3 Cincinnati Electronics technology improves situational awareness in combat intelligence, sighting & tracking systems, threat deterrence and perimeter & border security with all-weather observation, day or night. These IR sensors can be utilized in urban, rural and remote situations where there are extreme climatic and terrain conditions. Well-suited for fixed or portable payloads, these imaging systems offer a substantially lower total life-cycle cost in comparison to other commercial IR imaging sensors.

  • Torque & Load Cell Indicator

    9850 - Interface Inc.

    The model 9850's modular design allows the use of 7 different types of channel cards in 2 available channels. Available channels include AC mV/V for use with Rotary Transformer type torque sensors, DC mV/V, +/-5V or +/-10V, 4-20mA, Frequency (speed), Encoder and LVDT position sensors. A 3rd math channel allows display of calculate values such as horsepower, unit conversion, peak or valley, etc. The dual +/-10V analog outputs are assignable to any of the three channels. 2000 Hz sample rate allows true peak monitoring. Included software for graphical data display and logging.