Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 1261 - 1275 of 2267 products found.

  • Socket Wrench Torque Sensor Rotating Type

    RSS SERIES - Transducer Techniques, Inc

    Our RSS Series rotating socket wrench torque sensors are available in ranges from 10 ft-lbs. through 250 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. Unlimited rotation of the ball bearing supported sensor shaft allows monitoring of the total fastening cycle. The sensing element incorporates bonded foil strain gages of the highest quality, along with coined silver slip rings and two silver graphite brushes per ring for data transmission.

  • Bi-Directional Level Translator

    IFB-10001 - Playing With Fusion Inc

    Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.

  • Device Current Waveform Analyzers

    Keysight Technologies

    The dedicated Current Sensors measure from 100 pA level dynamic current up to 10 A with a maximum of 200 MHz bandwidth. The mainframe acquires the signal from the sensors by a maximum of 1 GSa/s sampling speed and 14-bit and 16-bit wide dynamic range. This combination allows you to measure quite wide range of dynamic current, for example, from standby/sleep state to active state, at a single measurement. In addition, the wide bandwidth and the high speed acquisition enable you to measure high speed pulse response even less than 100 ns previously very difficult with existing instruments.

  • Environmental Wafer Level Test Handler

    Aiolos - Afore

    Wafer level test handler for environmental sensors with with physical stimulus Vacuum probing, pressure probing, gas probing, humidity probing - AIOLOS is solution for these and much more. VVery high UPH capacity and the lowest cost of test (COT)AIOLOS has a unique automatic precision wafer prober placed inside chamber. Vacuum, pressure, humidity or gas stimulus is applied to whole wafer and wafer can be probed in stabile environment. Closed chamber with controlled humidity is perfect solution for temperature probing and lightless chamber can be utilized in testing of photonics in wafer level.AIOLOS is a solution for wafer level testing of pressure and environmental sensors, on bare wafer or on blue tape after dicing.

  • EPM Series Dual-Channel Power Meter

    N1914A - Keysight Technologies

    Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivityCode-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hostsAutomated frequency/power sweep measurements with the optional external trigger in/out feature

  • EPM Series Single-Channel Power Meter

    N1913A - Keysight Technologies

    Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivityCode-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hostsAutomated frequency/power sweep measurements with the optional external trigger in/out feature

  • Grid Analytics System

    Sentient Energy, Inc.

    Sentient Energy’s Grid Analytics System consists of intelligent sensors, distributed apps and the Ample Analytics suite. Sentient’s flagship, the MM3™, is an intelligent oscilloscope with high-performance sensors featuring substation-class measurement, computing and processing capabilities. Much like modern smart phones, Sentient MM3s can accept new apps downloaded over-the-air and be configured to meet the utility’s evolving needs. MM3s locally capture and process detailed data at many points along the network and communicate specific alerts and analyses to SCADA or Ample™ Analytics modules for feeder or system wide studies.

  • Wzzard Machine Condition Monitoring Application Bundle

    WSKIT3BE-CBM - B+B SmartWorx

    The bundle provides everything you need: the sensors, the wireless nodes, and the network gateway.Embedded magnets make mounting fast and easy.Low maintenance, multiyear operation on battery power. (2) AA lithium batteries are included.Wide temperature specifications and a rugged, outdoor-rated, industrial design.Remote diagnostics, automatic restart, hardware watchdog.Wireless mesh networks provide “five nines” (99.999 percent) uptime.Wzzard Intelligent Edge Nodes form self-healing wireless mesh networks.Up to 32 Wzzard Nodes and 96 individual sensors can be deployed in a single mesh network.Range is up to 100 meters indoors and up to 500 meters outdoors.

  • Torque & Load Cell Indicator

    9850 - Interface Inc.

    The model 9850's modular design allows the use of 7 different types of channel cards in 2 available channels. Available channels include AC mV/V for use with Rotary Transformer type torque sensors, DC mV/V, +/-5V or +/-10V, 4-20mA, Frequency (speed), Encoder and LVDT position sensors. A 3rd math channel allows display of calculate values such as horsepower, unit conversion, peak or valley, etc. The dual +/-10V analog outputs are assignable to any of the three channels. 2000 Hz sample rate allows true peak monitoring. Included software for graphical data display and logging.

  • WZZARD CONDITION BASED MONITORING KIT, CELL GW

    WSKIT3BC-CBM - B+B SmartWorx

    The bundle provides everything you need: the sensors, the wireless nodes, and the Cellular network gateway.Embedded magnets make mounting fast and easy.Robust network security and VPN tunneling capable.Wide temperature specifications and a rugged, outdoor-rated, industrial design.Wzzard nodes automatically create an alternate path to the network gateway if a node is disconnected. Individual nodes don’t need to be within direct range of the network gateway. They can route their data across fellow nodes.Up to 32 Wzzard Nodes and 96 individual sensors can be deployed in a single mesh network.Range is up to 100 meters indoors and up to 500 meters outdoors.

  • WZZARD ENERGY MONITORING KIT, 3 NODE, CELL GW

    WSKIT3BC-NRG - B+B SmartWorx

    The bundle provides everything you need: the sensors, the wireless nodes, and the Cellular network gateway.Embedded magnets make mounting fast and easy.Robust network security and VPN tunneling capable.Wide temperature specifications and a rugged, outdoor-rated, industrial design.Wzzard nodes automatically create an alternate path to the network gateway if a node is disconnected. Individual nodes don’t need to be within direct range of the network gateway. They can route their data across fellow nodes.Up to 32 Wzzard Nodes and 96 individual sensors can be deployed in a single mesh network.Range is up to 100 meters indoors and up to 500 meters outdoors.

  • Wzzard™ Energy Monitoring Kit

    WSKIT3BE-NRG - B+B SmartWorx

    The bundle provides everything you need: the sensors, the wireless nodes, and the network gateway.Embedded magnets make mounting fast and easy.Robust network security and VPN tunneling capable.Wide temperature specifications and a rugged, outdoor-rated, industrial design.Wzzard nodes automatically create an alternate path to the network gateway if a node is disconnected. Individual nodes don’t need to be within direct range of the network gateway. They can route their data across fellow nodes.Up to 32 Wzzard Nodes and 96 individual sensors can be deployed in a single mesh network.Range is up to 100 meters indoors and up to 500 meters outdoors.

  • Doppler Sensor Modules

    Sage Millimeter, Inc.

    Doppler sensor modules are speed sensors that are designed and manufactured to measure the speed and direction of moving objects. The operating frequency for these sensors is at 24, 76.5 and 95 GHz; the RF interface is a standard WR-42, WR-12 and WR-10 waveguide, respectively. The sensor modules support a TE10 mode operation and are configured with a T/R diplexer, a single or I/Q receiver and a transmitter/receiver oscillator in an integrated package. Models with an I/Q receiver can detect the speed and direction of moving targets simultaneously. While three catalog models with a single receiver are listed below, additional models, such as those with an I/Q receiver can be found on the website. In addition, custom models are available to meet unique application needs.

  • Multi-Sensor Systems

    Inframet

    Multi- sensor surveillance systems represent a fast growing group of electro-optical systems of critical importance in both defense and civilian applications. At the same time they are the most expensive groups of electro-optical systems. Most advanced but rarely met multi-sensor surveillance systems are built from a long series of sensors like thermal imager (or two thermal imagers, color VIS camera, low light VIS-NIR camera, SWIR camera, laser range finder, laser designator, laser pointer, illuminator located on a stabilized platform and such systems. Simpler systems built from two-three sensors located on smaller stabilized or non-stabilized platforms are more common.

  • MWIR Systems

    L-3 Cincinnati Electronics

    L3 Cincinnati Electronics’ high-performance cooled mid-wave (3.5 – 5.0 µm) IR imagers are based on our patented InSb focal plane array architecture. Ideal for all combat conditions, L3 Cincinnati Electronics technology improves situational awareness in combat intelligence, sighting & tracking systems, threat deterrence and perimeter & border security with all-weather observation, day or night. These IR sensors can be utilized in urban, rural and remote situations where there are extreme climatic and terrain conditions. Well-suited for fixed or portable payloads, these imaging systems offer a substantially lower total life-cycle cost in comparison to other commercial IR imaging sensors.