Filter Results By:
Products
Applications
Manufacturers
Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Camera Link, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
product
Modbus Master Data Scanner
ModScan
ModScan is a Windows application which operates as a modbus master. It allows you to access and change data points in a connected slave device using either the RTU or ASCII Transmission mode. ModScan is ideally suited for quick and easy compliance testing of the modbus protocol and its built-in display of serial traffic allows effective troubleshooting of field connections.
-
product
ATCA Rear Transition Module
ART103
The ART103 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC103 carrier board. The ART103 is a passive RTM that allows for the additional connectivity of two GbE ports, Management 10/100Mbit Ethernet, Management RS-232 serial interface and three PCIe x4 lanes for expansion. One of the PMC J4s (user defined I/O) is routed to the back.
-
product
Camera Link Frame grabber
Cyton-CXP
CoaXPress (CXP) is a simple, yet powerful, standard for moving high speed serial data from a camera to a frame grabber. Video is captured at speeds of up to 6.25 Gigabits/Second (Gb/S). Simultaneously, control commands and triggers can be sent to the camera 20 Mb/S (with a trigger accuracy of +/- 2 nanoseconds). Up to 13 W of power can also supplied to the camera.
-
product
Infiniium V-Series Real-Time Oscilloscopes
V-Series
Bandwidth upgradability to 33 GHz for best investment protection Maximize eye height measurements with the least amount of noise contribution from the oscilloscope See the truest jitter performance of your design with the lowest 100 fs oscilloscope intrinsic jitter Debug some of your most difficult designs with the industry’s longest hardware serial trigger
-
product
Plus Super Phosphor Oscilloscopes
SDS2000X
The SDS2000X Plus series employs SIGLENT’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 50 MHz waveform generator, as well as serial decoding, mask test, bode plot, and power analysis are also features of the SDS2000X Plus. A 10-bit acquisition mode helps to satisfy applications which require more than 8-bit resolution.
-
product
Data Link Monitor
Listen32
Listen32 is a 32-bit version of Listen which includes all the above features plus the ability to launch and monitor communications from separate Win32 processes without being physically connected to the serial cable. It operates much like the Socket Spy applications, hooking the communications API within Windows by launching a target application using the Win32 Debugger API.
-
product
Dataloggers
Data loggers with one or more signal channels for DC and AC voltages and currents, thermocouples, Pt thermometers, process signals and serial data interfaces RS232 / RS485 are designed for industrial use. They can also be used as monitors or process controllers with additional data and signal outputs for control purposes. The devices are designed for panel construction and have communication software for Windows applications.
-
product
ETX
The ETX modules (114 x 95 mm) are very compact and highly integrated SBCs that integrate core CPU and memory functionality, standard personal computer (PC) peripheral function such as graphics, USB, serial and parallel ports, keyboard/mouse, Ethernet, IDE, PCI, and ISA buses. All ETX modules have a standardized form factor and a standardized connector layout.
-
product
Lab Moisture Analyzer
PC-Based laboratory/production Moisture Analyzer connects through the RS-232 Serial Port. For nuts, granules, powders, pellets, chips or flakes. Complete with:– MCPC-RS Test Chamber– Windows PC-Based Software– Two Sample Cups– Dial Thermometer– Standard Block– RS-232 Cable (10 Feet)– USB to RS232 Adapter– Operating Instructions Manual– 115VAC/60HZ Wall Transformer
-
product
SparkFun Shift Register Breakout
74HC595
This is a breakout for the SOIC version of the 74HC595 shift register IC. Clock in data and latch it to free up IO pins on your micro. All pins from the IC are broken out to standard 0.1" spaced headers. The Serial in and out pins are on opposite sides of the board with the remaining pins carried over so that multiple shift register boards can be chained together.
-
product
Surface Resistance Tester
MR – 1
The different specific resistances are specified by selecting one of the pre-programmed materials, or by measuring the specific resistance of unknown materials and entering the result. Preferably the coat thickness is displayed, but the measurement and display of the actual resistance, the square resistance and the specific resistance is possible, too. All measured values can be transmitted into a PC via a serial interface. Controlling the MR-1 on the other hand is not possible.
-
product
Ruggedized Field Deployable Tester
PUMA
- 18-slot PXI / 4-slot SCXI Chassis- 1.2 GHz Embedded Controller- 4-axis Motion Controller/Simulation- 8-port RS-232 Serial Module- 4-port RS-485 Serial Module- 48 bit Isolated Digital I/O- Reconfigurable multi-function I/O FPGA Module- 5 1/2 digit DMM- 200 MHz 2-channel Scope/Digitizer- Multi-function Data Acquisition (DAQ)- 8-channel Analog Input Module- 6-channel Analog Output Module- General Purpose Switching- RF suite (optional)
-
product
Data Converters
Omega carries an extensive line of data converters, including RS-232 to USB interface converters, fully isolated RS-232 to RS-485 converters, industrial ethernet to serial device servers, and more.
-
product
6U CompactPCI Rear Transition Module with Ruggedized M12 Connectors
cPCI-RMPSA
*Dual display with DVI-I and DVI-D*Ruggedized USB 2.0, GbE M12 ports*Dual serial ports and optional USB 3.0*Compatible CPU boards: cPCI-6530/cPCI-6520/cPCI-6940
-
product
XMC Module Carrier PCI Express x 4
SK2-SESSION
SK2-SESSION is a bidirectional 4-lane PCI Express® Gen3 redriver, for optimum 8GT/s high speed signal integrity, and can be installed into any peripheral slot of a CompactPCI® Serial backplane.
-
product
Communication Converter
F485
The F485 is a self-contained device for converting between RS232, RS485 and fiber optic signals. The F485 is electrically isolated to improve communications in noisy environments. The converter uses internal switches to select the signal conversion type and communication rates up to 57600 bps. The F485 converter uses the data on the serial ports to determine direction and therefore requires no hardware handshaking signals from the computer.
-
product
LAN⇔RS-232C Conversion
SI-60
SI-60 is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). The device supports 35mm DIN rail and the wide range of operating temperature. Therefore, you can use it for factory automation without worry.
-
product
Switching Unit
ZET 454
The ZET 454 switching unit is intended for serial switching of 72 circuits of ZET 452 control devices to one of the sixteen sockets. The ZET 452 electric circuits control device is connected to a socket on the ZET 454 switching unit front panel. On the front panel of ZET 454 there also are sockets for tested device circuits connection, which is performed using the adapter harnesses.
-
product
USB Connectivity Bridges
USBXpress
Silicon Labs USBXpress devices are highly optimized solutions that enable designers to easily add USB to existing and new applications. These fixed function devices provide the easiest method to add USB without the need for any firmware or driver development. USBxpress portfolio supports several USB to serial bridge devices including human interface (HID) devices and USB Audio devices.
-
product
ATCA Rear Transition Module
ART108
The ART108 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC108, ATC104, etc. carrier board. The ART108 is a passive RTM that allows for Management RS-232 serial interface and PCIe x4 lanes for expansion. The PCIe x4 is either with Fiber or Copper. The Copper interface is via I-PASS x8 PCIe connector while the Fiber interface is via quad SFP interface.
-
product
Digital & ARINC Standards Display Panel
TA-3001
This is our soon to be introduced Digital Standards Panel. (2ND QTR) This panel is available with or without a Precision Resolver drive. Included on the panel are four digital displays; TA-902 API, TA903-01 OBI, TA903-02 Distance and a TA903-03 serial distance display. This panel when paired with the TA-3000 GPS/FMS test panel will make one of the most capable testing solutions available today
-
product
Digital I/O Adapter Module For FlexRIO
Digital I/O Adapter Modules for FlexRIO offer up to 54 channels of configurable digital I/O that can interface with single‐ended, differential, and serial signals at a variety of voltage levels. When combined with a large, user‐programmable FPGA, you can use these modules to solve a variety of challenges, from high‐speed communication with a device under test to emulating custom protocols in real time.
-
product
Electrical Network Analyzer
SHARK 200
*Compact design*Class 0.2 in energy, typical accuracy 0.1%*Front serial port for programming once installed*Integrated RS-485 (Modbus and DNP 3.0 protocols)*Self-range in voltage and current
-
product
LIS3DH 3-Axis Accelerometer With ADC
29020
The LIS3DH is a high performance, ultra-low power, three-axis linear accelerometer. It features user-selectable scales up to 16g, an embedded temperature sensor, 10-bit ADC and a standard digital I2C/SPI serial interface.
-
product
XMC Module Carrier PCI Express x 8
SK4-WALTZ
SK4-WALTZ is a bidirectional 8-lane PCI Express® Gen3 redriver, for optimum high speed signal integrity, and should be installed into a fat pipe peripheral slot of a CompactPCI® Serial backplane.
-
product
Signal Generator
Tektronix signal generators cover a wide range of applications, from replicating sensor signals to creating RF and the fastest high speed serial data signals. Each versatile signal generator can create a virtually unlimited number of signals - analog or digital, ideal or distorted, standard or custom. From the world's only direct synthesis of high-speed serial data waveforms for simplified receiver testing, to the world's most versatile arbitrary function generator for common stimulus signals, Tektronix has a signal generator to meet your debug challenge.
-
product
Flash SATA DOM
FSD Series
Axiomteks FSD (Flash SATA DOM) series is designed into Serial ATA II protocol type with compatible Serial ATA standard interface based on flash memory technology. This flash module is offered with various capacities ranging from 128 MB up to 32 GB and can operate under industrial temperature range goes from -40°C ~ 85°C in the harsh operating environments. The features of reliability, high performance, cost-effective and easy-tointegrate designs make FSD series a perfect solution over traditional storage devices.
-
product
Legacy Product
PXM-C388-S
WINSYSTEMS’ PXM-C388-S is an industrial Single Board Computer (SBC) with PC/104 and SUMIT AB expansion that uses Intel’s Atom N455 single core 1.66GHz processor paired with the ICH8M I/O controller hub. The SBC is full-featured with onboard I/O that supports CRT/LVDS video simultaneously, a Gigabit Ethernet port, eight USB 2.0 ports, two serial RS-232/422/485 COM channels, two serial RS-232 COM channels, 24 digital I/O lines with event sense, audio, and a watchdog timer.
-
product
Networked Absolute Inclinometer
T7
The T7 is available in several interface and protocol options. The physical interface can be RS232, RS485 or US Digital's CAN (Controller Area Network). The protocol can be either US Digital's serial protocol or Modbus RTU. The RS232 version supports a single T7 with up to 100 ft of cable. For users that need longer cable lengths or multiple T7s on a single bus, the RS485 or US Digital CAN (Controller Area Network) version can be used. The USD-CAN protocol allows a network of up to sixty-four T7s to be connected to a single host. Power for each T7 is supplied over the CAN network cable. The host accesses the USD-CAN T7s through US Digital's low cost CANA-232/CANA-485 adapter module. This module allows the host to access each T7 on the network using simple, easy serial port commands, just like the RS232 version. The RS485 version supports up to 32 T7s on the bus.
-
product
LinkExpert Software
LinkExpert enables complete control and management of Teledyne LeCroy's family of Protocol Analyzer and Exerciser hardware. LinkExpert provides a convenient interface to run Compliance, Conformance and Validation tests on PCI Express (PCIe) and SAS (Serial Attached SCSI) links. The LinkExpert software interface is provided free of charge and includes as standard, several validation tests for PCIe Hosts (Root Complexes) and Devices (End Points).