Filter Results By:
Products
Applications
Manufacturers
Servo
feedback seving to control.
- TEAM SOLUTIONS, INC.
product
Motion Control Board, PCI
APCI-8001-1
*Axis control for 1 servo or stepper motor*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders *or SSI absolute encoders
-
product
3U OpenVPX SOSA™-aligned PWM Servo Motor Drive
68PW1
The 68PW1 is a 3U OpenVPX SOSA™-aligned (basis, Snapshot 2) single-axis PWM servo motor drive that can be configured with closed loop feedback measurement options including Hall, Resolver/Synchro or Encoder. The PWM drive provides programmable PWM output drive (up to 65 V @ 10 A continuous) from a single +28 VDC input source. Ideally suited for rugged Mil-Aero applications, the 68PW1 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
product
DC Control Tools
Assembly designs are getting more and more complex while production speeds continue to increase. To compete, lean manufacturers strive to complete more work with fewer tools. A single Mountz DC control tool can do the work of 2-15 regular tools, saving space and increasing production. Mountz DC control tools are easy to program and can remember up to 30 process sequences with 20 program steps. This gives you the flexibility you need to carry out varied and complicated manufacturing plans. A Swiss DC servo motor controls torque delivery with clockwork repeatability. Combined with built-in screw counters and error-proofing software, Mountz DC control tools offer supreme production results and product oversight. And by providing documented fastening results, Mountz DC control tools also make regulatory compliance easy.
-
product
Decoders
SwitchPilot
Electronic Solutions ULM GmbH & Co. KG
The ESU SwitchPilot Decoder is especially optimised for the stationary use on your layout. Regardless of what you prefer, the usual twin coil magnetic switches, switching electrical light signals or an ultra-modern servo control: One of the SwichtPilot decoders will "fit".
-
product
Drives
Haydon Kerk and Pittman offer a range of advanced Stepper and Brushless motor drivers to complement its linear and rotary motors. Our Haydon Kerk and Pittman drives are available in many configurations from simple analog controlled single quadrant drives to fully programmable servo motion controllers.
-
product
Econo Motion Controllers
DMC-41x3
The DMC-41x3 motion controller is one of Galil's latest generation, stand-alone motion controller. Compared with the DMC-21x3 controller, the DMC-41x3 offers the following enhancements: 100BASE-T Ethernet, aux RS232 port, USB port, uncommitted analog inputs, up to 15 MHz encoder frequencies, more program memory, and faster sample frequencies. The DMC-41x3 also accommodates the same stepper and servo motor drives used in the DMC-40x0 series and allows two 4-axis 750 W drives to be installed in the 8-axis controller package. The DMC-41x3 is available as a box-level or card-level motion controller. The unit operates stand-alone or interfaces to a PC with Ethernet 10/100BASE-T, or USB. It includes optically isolated I/O in addition to analog inputs and outputs. The DMC-41x3 controller and drive unit accepts power from a single 20-80 VDC source.
-
product
Electric Servomotor Free Fall Tester
An electric servo motor type packaged cargo drop tester compliant with "JIS Z 0202 Packaged cargo-Drop test method". It is possible to test large test pieces safely, stably and quietly.
-
product
Electric Servo Motor Type 2 Axis Switching Simultaneous Vibration Tester
It is a 2-axis switching vibration tester and a 2-axis simultaneous vibration tester that mounts an electric servomotor actuator on the vibration drive unit.
-
product
Electric Servo Motor Type Horizontal Impact Tester
This is a horizontal impact tester using an electric servo motor type actuator system.
-
product
Electronic Pressure Comparator
Huaxin instrument (Beijing) Co., Ltd
When it comes to simultaneous pressure calibration for several pressure measuring instruments, electronic pressure comparator is always a great choice for most of people. The comparison calibrator features 5 pressure ports which allow simultaneous connection of 4 pressure gauges under test, making calibration more efficient and time saving. It also comes with an external air source for easy and precise pressure generation and servo valve for stable pressure control.
-
product
EOL RF Functional Test
AS652
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
product
EtherCAT Master Multi-Axis Motion Controllers
DMC-500x0
The DMC-500x0 EtherCAT Controller is Galil Motion Control's newest entry in its latest generation of digital motion controllers. Incorporating all of the features of our flagship Accelera series controller and designed with compatibility and flexibility in mind, the DMC-500x0 allows integration of remote EtherCAT drives into new and existing applications with just a handful of configuration commands. The DMC-500x0 is offered in 1 through 8 axis formats. Axes 1 - 4 can be configured as either local or EtherCAT drives while axes 5 – 8 can be configured for additional EtherCAT drives. Unique to the motion control industry, this ability to mix and match local and EtherCAT drives on the same controller provides increased flexibility for any application. In addition, the DMC-500x0 is fully compatible with Galil’s internal servo and stepper motor amplifiers as well as third party external drives.
-
product
EtherCAT Master Multi-Axis Motion Controllers
DMC-52xx0
The DMC-52xx0 EtherCAT Master is Galil Motion Control's first 32 axis motion controller. It is a pure EtherCAT controller capable of controlling up to 32 drives and 2 IO modules on one EtherCAT Network in a small, space efficient package. The DMC-52xx0 makes configuration and programming easy with just a handful of EtherCAT configuration commands and Galil’s intuitive, two-letter programming language. The DMC-52xx0 is offered in 2, 4, 8, 16, and 32 axis formats. Coordinated moves can be done within banks of 8 allowing for minimal changes to Galil’s programming language. Galil supports a variety of EtherCAT drives to accommodate most applications. The DMC-52xx0 operates in Cyclic Synchronous Position mode (CSP). In this mode the servo control loop is closed on the EtherCAT drive while the Galil sends motion profile data at a 1 kHz rate. The DMC-52xx0 features 8 uncommitted opto-isolated inputs and 8 uncommitted opto-isolated high power outputs. It also includes 8 uncommitted analog inputs and 8 uncommitted analog outputs. One 100 Mbps Ethernet port and one USB (serial) port are provided for communication with a host PC or external devices.
-
product
Gas Distribution Panels
PTS DII
PTS DII Gas Distribution Panels are similar to our PAO-DII Fluid Distribution Panels. They are designed to individually distribute, monitor, and protect one or more of your valuable products from the higher than required flow of a larger PTS, Portable Temperature Servo Conditioner or HPG, High Pressure Gas Conditioner. You can also use PTS-DII Gas Distribution panels with any other source of temperature controlled gas, including a competitor's air or gas source.
-
product
ISA Optima Motion Controllers, 1-8 axes
DMC-1700
The DMC-1700 for the ISA bus is a member of the Optima Series, Galil's full-featured multi-axis motion controllers. Designed to fit in a single ISA slot of a PC, the DMC-1700 controllers accommodate 1- through 8-axis formats and allow control of step or servo motors on any combination of axes. Any mode of motion can be programmed including linear and circular interpolation, contouring, electronic gearing and ecam.
-
product
Low Frequency Vibration Signal Conditioner
A compact Signal Amplifier to make optimal signal processing being connected with the Servo type Accelerometers. It is used for Vibration Acceleration Measurement, Waveform Observation, for various Analysis in combination with the AC Voltage Meter, Oscilloscope, FFT Analyzer respectively. Furthermore, Voltage signals from the Microphones or Sound Level Meters can be output to the instruments like Recorders along with the Vibration Signals.
-
product
Motion Control Board, PCI
APCI-8001
*Axis control for 3 servo or stepper motors*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders or SSI absolute encoders*Possibility of extension to a total of 8 axes*Menu-driven test application
-
product
Multi-Axis Motion Controllers
DMC-1800
The DMC-1800 for the PCI bus is a member of the Optima Series, Galil's full-featured multi-axis motion controllers. Designed to fit in a single PCI slot of a PC, the DMC-1800 controllers accommodate 1- through 8-axis formats and allow control of step or servo motors on any combination of axes.
-
product
Multi-Axis Stage Controller
MS-2000-WK
Applied Scientific Instrumentation
*100 MHz Microcontroller for faster command processing and servo control.*Closed-loop DC servo control of up to four motorized axes.*Firmware upgradeable via serial connection.*0-10V DAC for single piezo axis control.*Remembers last position on power down/up.*LCD display shows axes coordinates and status.*"Zero" and "Home" buttons for simple stand-alone operations.*USB or RS232 serial control with baud rates to 115200 Baud.*Compact ergonomic tabletop control unit 6"D x 9"W x 3"H (16 x 23 x 9 cm).
-
product
Nanopositioning Stage & Controller
PInano
Physik Instrumente GmbH & Co. KG
PInano® XY and XYZ low-profile piezo scanning stages are optimized for easy integration into high-resolution microscopes. They feature a very low profile of 20 mm (0.8") and a large aperture designed to hold Petri dishes and standard slide holders. The long travel ranges of up to 200 x 200 x 200 µm with nanometer closed-loop resolution are ideal for leading-edge microscopy and imaging applications. PInano® series piezo positioning stages are available in two versions: A) Highest Stability, Linearity and Precision with capacitive feedback sensors. B) High Precision with lower cost piezoresistive sensor feedback. Both types provide very high sensitivity and responsiveness as well as nanometer resolution. A proprietary servo controller significantly improves the motion linearity of the piezoresitive version compared to conventional piezoresistive sensor controllers.
-
product
Passive Hydrogen Maser
VCH-1008
The VCH-1008 Passive Hydrogen Maser is a compact hydrogen maser with excellent frequency stability and utilises state-of-the-art technology. Full digital processing of the modulation and servo loop signals makes it ideal for high accuracy applications. An internal GPS/GLONASS option is available and provides automatic output signal frequency calibration.Key applications:- National Time Keeping Service- Space tracking and navigation- Verification of frequency signals - Scientific research
-
product
PCI 1-Axis Motion Controller
DMC-1417
The DMC-1417 for the PCI bus is a member of the Econo Series, Galil's latest generation of single-axis motion controllers which are half the size and half the price of multi-axis controllers. The DMC-1417 can handle the most demanding applications with such features as an extra encoder input for electronic gearing, program memory with multitasking, uncommitted I/O and user-selectable stepper or servo motor control.
-
product
PCI Bus Controllers
DMC-18x6
The DMC-18x6 PCI bus controllers belong to Galil's latest generation motion controller family: the Accelera Series. Incorporating a 32-bit Risc-based microcomputer, these new controllers offer high-speed performance and processing power. Speed improvements include acceptance of encoder inputs up to 22 MHz, servo update rates as low as 24 microseconds/axis, and command execution speeds as low as 40 microseconds
-
product
Portable Load Cell System
Load Cell is designed by Seismic Source Company to measure the Hold Down weight and the output force of the Servo Hydraulic Vibrator unit. The output of the Load Cells can be recorded with any accurate seismic recording system.
-
product
Precision Capacitive Position Sensor
8810
The MicroSense model 8810 is a non-contact precision position sensor. The 8810 is designed for best linearity and stability, with measurement bandwidth up to 20 kHz – ideal for servo system position feedback and fast tool servo applications
-
product
Precision Positioning stage
N-661
Physik Instrumente GmbH & Co. KG
Miniature Linear Stage with NEXACT Drive Travel Range 20 mm Self Locking at Rest, no Heat Generation, no Servo Dither Compact Design: 70 x 50 x 20 mm Zero-Wear Piezo Stepping Drive, Ideal for Micro- and Nano-Manipulation Integrated Linear Encoder Option for Highest Accuracy with 20 nm Resolution Two Operating Modes: Continuous Stepping Mode and Continuously Variable, High-Dynamics Analog Mode for 30 pm Resolution** Up to 10 N Force Generation
-
product
Rack Mount Stage Controller
RM-2000
Applied Scientific Instrumentation
*2U 19" Rack Mount Control Unit: 22.8D x 48.3W x 8.1H cm (9" x 19" x 3.2").*100 MHz Microcontroller for Faster Command Processing and Servo Control.*Closed-Loop DC Servo Control of up to Four Motorized Axes.*0-10 Vdc DAC Output for Additional Analog Control.*Firmware Upgradeable via Serial Connection.*Remembers Last Position on Power Up.*LCD Display Shows Axes Coordinates and Status.*USB or RS-232 Serial Control with Rates to 115200 Baud.*"Zero", "@", and "Home" Buttons on Joystick.*Left- or Right-Hand Joystick Unit.
-
product
Read-Write Analyzers
Guzik Read/Write Analyzers (RWA) work in conjunction with Spinstands to write data to the disk media and read back the signal for detailed analysis. We have two RWA-4000 series available for For Two Dimensional Magnetic Recording (TDMR) and non-TDMR technologies. The RWA 4000 series offer upto 8Gbit/sec maximum write data rate and 3.5 GHz analog bandwidth for all parametric measurements. Each RWA features a pattern generator with 1psec resolution of bit pre-compensation and supports PRML chip integration. Servo writing and processing is provided for Guzik Spinstand models. Select the pre-amplifier (UP14) as well as a variety of enhancements including programmable filters and PRML chip adapters.
-
product
Scanners
All BK Mikro scanners utilize servo motors for accurate measurements and increased lifetime.
