Filter Results By:
Products
Applications
Manufacturers
Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
product
Video Signal Generator
MSPG-2000
MSPG-2000 Video Signal Generator, was designed to test standard Panel and Multimedia Video Signal. Separated four(4) boards generate selected own(1) Time & Pattern and output to the each section with two(2) ports.
-
product
Video Signal Distributor
MSDD-02D
MSDD-02D distribute the Analog Signal through the two (2) output without any diminution & distortion. The DDC line is designed with consisted of the two (2) channels in order to make the EDID data set up with the two (2) displays monitors at the one (1) same time. With two (2) generation by adapt as individually using the quick speed IC for exact output at the video data respectively, there is no signal deviation between input & output signal.
-
product
Video Signal Distributor
MSHM-410A
HDMI Distribution Amplifier, allows four (4) digital video sources to be spilt into ten (10) digital displays. The built-in amplificationfunction enables HDMI signal distribution without signal loss. The product guaranteed to support full channels HDMI/HDCP compliance.
-
product
Video Signal Distributor
MSHM-48UD60
MSHM-48UD60 is a four input, eight output distribution amplifer for HDMI signals. It supports resolutions up to 3840x2160/60Hz RGB 444/YCbCr444,422,420 with mixed EDID, HDCP 2.2 and 3D.
-
product
Video Signal Generator
PC Slot Type
M-100AD/A/C/Y/H/D, PCI type Signal Generator, was designed to make user can insert needed slot at Computer. Slot composed with Analog & DVI, Analog, CVBS, &S-Video, DTV, HDMI nd DVI type. It is operating with exclusive PC Program(User Interface) which is Master supplied.
-
product
Video Signal Distributor
MSVD-250N
MSVD-250N is a Analog Distributor Buffer that distribute one (1) input signal to the 5/10/15/20 channels. User can select input type between 15P D-Sub and 5 BNC (R,G,B,HS,VS). The distribution buffer can be used in factory assembly lines, repair depots, and for system integration to save cost and time.
-
product
Video Signal Distributor
MSHD-10N
MSHD-10N distribute received one(1) D-TV(Y,Pb, Pr) and audio(R,L) signal to the ten(10) channels. It is recommended reliable test room and show room.
-
product
Video Signal Distributor
MSDS-4416
MSDS-4416 distribute four TMDS input signal up to four display devices such as Projector, PDP, HDTV and TFT-LCD without diminution and distortion. The distribution support single/dual 8~16 bit and user can select input signal by press button and make sure being connected input source with led of the front panel.
-
product
Video Signal Generator
MSPG-5140M
MSPG-5140M is able to output of LVDS Signal. MSPG-5140M can support Max 500MHz High frequency and MSPG-5140M has Touch Screen & Graphic LCD. MSPG-5140M can device up-grade & Option data copy easily by USB Memory stick. MSPG-5140M supports Backlight Power of LCD Panel. And this can control DC Power (0V~27V) as 0.1V unit step.
-
product
Video Signal Distributor
MSHM-305A/310A
MSHM-305A/310A, HDMI Distribution,Amplifier, distribute three digital video input sources to the five (or ten) output channels. The built in amplification function enables HDMI signal distribution without signal loss. The product guarantees to support full channels HDMI/HDCP compliance. User can select one input source of the three and make sure connected condition with led of the front panel.
-
product
Video Signal Generator
MSPG-4233MT
MSPG-4233NT is basically supporting the Teletext and Closed Caption as multi broadcast for the D-TV(NTSC, PAL), as well as V-Chip(Violence Chip) function to block the violence and sex etc. bad program to protect a person under age through the regulation grade.
-
product
Video Signal Generator
MSHG-800Plus
MSHG-800Plus construct HDMI 2.0(HDCP 2.2) 4Port, HDMI 1.4 & MHL 2.0 1Port - HDMI 2.0 (HDCP 2.2) supports 4Ports - HDMI 1.4 (HDCP 1.4) & MHL 2.0 supports 1Port - 4 Ports ARC functions supports - RS-232C Control supports - Each outputs status with front LED button - Button locking function - Easy upgrade / update to USB memory stick
-
product
350 MHz, 2 Analog Plus 16 Digital Channels Oscilloscope
MSOX3032A
350 MHz2 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
product
3-Port ROADM / TOADM
Optoplex's Reconfigurable Optical Add/Drop Multiplexer (ROADM) module, also known as Tunable Optical Add/Drop Multiplexer (TOADM), is based on a proprietary micro-optics and micro-actuator design, athermal packaging technology, and state-of-the-art thin-film coating. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), this 3-port ROADM device directs a selected channel to the Drop-Port (ADD/DROP) and the remaining channels to the Express-Port (EXP), as depicted in the figure below. This tunable feature can also be used for adding a channel, when the device is used in reverse. Cascading two ROADM modules, simultaneous add and drop functions can be achieved. Each single ROADM device is optimized to cover either C- or L-band wavelengths. The standard 100- or 200-GHz channel spacing ROADM products allow for single-channel drop. Customized banded-channel drop ROADMs are available upon request.
-
product
2x8 QPSK Mixer
To be used for optical coherent detection such as DP-QPSK receivers, Optoplex’s ten-port 2x8 Coherent Mixer (aka QPSK mixer) combines the incoming signal with a local oscillator to generate eight light states in the complex-field space. The eight light output signals can then be coupled into four pairs of balanced detectors. The block diagram below shows the application of a 2x8 coherent mixer in a DP-QPSK receiver. Since the mixing process is data rate independent, the devices can be used for any data rate in applications such as 40Gb/s or 100Gb/s transmission systems.
-
product
DPSK Demodulator
Optical differential-phase shift keying (DPSK) provides a desired modulation format that offers high receiver sensitivity, high tolerance to major nonlinear effects in high-speed transmissions, and high tolerance to coherent crosstalk. In DPSK, data information is carried by the optical phase difference between adjacent bits. For direct detection of DPSK signal (by conventional intensity detectors), a DPSK demodulator is needed to convert the phase-coded signal into an intensity-coded signal.
-
product
40Gb/s DPSK Receivers
Targeting for the next-generation 40Gb/s system based on advanced optical differential phase shift keying (DPSK) demodulation, Optoplex’s 40Gb/s Integrated DPSK Receiver (DPSK Rx) demodulates an incoming DPSK optical signal into a pair of differentially (amplitude) modulated RF outputs at data rate up to 43Gb/s in a compact package. Phase modulated optical signals offer much better dispersion performance compared with traditional amplitude modulated counterparts because the carrier light stays on all the time so that the intensity-dependent nonlinear effects in the transmission link are avoided, resulting in longer transmission distances.
-
product
90-Degree Optical Hybrid
Six-port hybrid devices have been used for microwave and millimeter-wave detection systems since the mid-1990s and are a key component for coherent receivers. In principle, the six-port device consists of linear dividers and combiners interconnected in such a way that four different vectorial additions of a reference signal (LO) and the signal to be detected are obtained. The levels of the four output signals are detected by balanced receivers. By applying suitable baseband signal processing algorithms, the amplitude and phase of the unknown signal can be determined.
-
product
2x4 QPSK Mixer
Optoplex's 2X4 polarization diversified optical hybrid (aka QPSK Mixer) is a 2x4 device, which mixes an incoming signal with a local oscillator. The 4 outputs of this device are connected to 4 single-ended detectors (see the function diagram below). The device features a monolithic optical core integrating a PBS with an interferometer which is also widely used in Optoplex's interleaver and DPSK-demodulator platforms. This device is athermal, colorless, data-rate independent, compact in size and designed for manufacturability. This platform can also be extended to a 2X8 polarization diversified hybrid to incorporate with 4 pairs of balanced detectors.
-
product
Standard Optical Interleaver
An innovative technique for expanding the number of channels per fiber involves an optical device, called an optical interleaver. For example, in most DWDM equipment, the standard channel spacing is 100 GHz. But spacing the signal-carrying frequencies every 50 or even 25 GHz can double or even quadruple the number of channels per fiber. This job is accomplished by an optical interleaver. Such a device takes two multiplexed signals with 100-GHz spacing and interleaves them, creating a DWDM signal with channels spaced 50 GHz apart. The process can be repeated, creating even denser composite signals with 25-GHz or 12.5-GHz spacing. The signals at the receiving end are recovered with the same devices used as splitters or optical de-interleavers. Thus, devices and/or networks can be upgraded without requiring that all devices be upgraded, or network bandwidth can be increased.
-
product
Timing Controller
MS 2009
MS5128 Timing Controller has programmable logic generation, Input Output Signals Interface, Timings, macro-cells, Pins, internal timing delay and Signal Levels for airborne microprocessor boards.
-
product
Airborne Video Delay Board
MS 2006
- Spartan FPGA based Design- Customized design for delaying & switching video inputs to RF section- Interface with EW Signal Processor Unit- Two channel video inputs and control- Video Signal Delay from 1ns to 1ms- Over duty Indications- Inhibit Control- Discrete Interface
-
product
PCM Generator
MS 1607
The PCM Generator System used to generate different types of PCM format signals. The user can configure the PCM format to be generated. This system is an independent unit with LCD and Keypad for user interface. Primary application of the system lies in testing the airborne equipment.
-
product
Receiver And Exciter
MS 2010
Receiver Exciter is used to receive and transmit HF range signals & processing HF signals into voice and data format using DSP technology. It consists of high quality HF receiver and HF exciter. System has SELCAL and secure communication features. System has configuration facility for Frequency range, mode of operation (AM, LSB, USB, DATA, CW), volume, squelch level from external control unit. The exciter produces the low power signal which is fed to the power amplifier unit.
-
product
Intel x51 Based Boards
MS 1507
- General Purpose I/O Signals- RS232/422 Interface- External Bus, External Interrupts
-
product
Signal Processor Board
MS 1532
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
product
9U ATE Rack
MSMI 1014
- Capable of handling up to 2688 IO signals- Capable of handling up to 1344 Power signals- Portable and Rack mountable- Suitable for more depth PCBs (up to 410mm)- Fourteen PCBs can be accommodated with Fascia plate of 30 mm width
-
product
PCI Express To CPCI Board
MS 1719
PCI Express to CPCI card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit cPCI signals from/to the Host System. These cPCI signals are converted into PCI Express using cPCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
product
Airborne Receiver
MS 2015
Receiver shall receive the telemetry signal transmitted by the airborne TGS unit. This unit is a single conversion super heterodyne FM receiver operating at 1486.5MHz. This unit has four connectors. They are RF input connector (J1), Power connector (J2), Signal connector (J3) for AGC signal and a Video output connector (J4). This unit operates at 28V DC and consumes a typical power of 5.6 watts.
-
product
WCS Simulator
MS 1601
The WEAPON CONTROL SYSTEM SIMULATOR (WCSS) is used to simulate Aircraft Bomb and Rocket release commands for the LAB testing of WCSTS. The WCSS system simulates the High current and Low current signals according to the mode of operation (Series).
