Showing results: 3316 - 3330 of 8180 items found.
-
PCIe-6208 -
ADLINK Technology Inc.
ADLINK PCIe-6208 series are 8-CH, 16-bit, PCI Express analog output cards which provide high resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
PQM-703 -
Sonel S.A.
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
BAW -
Macom Technology Solutions Holdings Inc.
MACOM’s BAW product portfolio is ideal for high performance Industrial, Aerospace, Defense, and Communications applications that require critical frequency filtering. Our high-performance RF filters enable our customers manage signal integrity in the 1 to 6 GHz frequency range. Bulk Acoustic Wave Resonators consist of two metal electrodes above and below a layer of a piezoelectric material. The piezoelectric material converts an electrical signal to a mechanical signal and vice versa. The metal electrodes provide the connections to/from the piezo material. The frequency at which resonance occurs depends on the thickness of the combined metal-piezo-metal stack. Advances in thin-film piezoelectric fabrication have enabled BAW resonators to meet RF filtering challenges up to 6000 MHz using standard MEMS fabrication process. High-performance BAW resonators-based RF filters are made of piezoelectric material having high Q-factor (>3000) and high coupling coefficient. Currently, no competitive technology provides the same high performance for RF filter applications when compared to BAW resonator-based RF filter up to 6000 MHz for the same size and cost.
-
U1832C -
Keysight Technologies
The USB-powered (USB TMC compliant) U1832C provides broadband noise figure measurements from 500 MHz – 50 GHz with modular signal analyzer, benchtop X-Series signal analyzers and Fieldfox
-
HR2040A, HR2040B -
Hangzhou Huatai Optic Tech. Co., Ltd.
HR2040 series HFC four ways return path receiver can convert upstream optical signal to RF signal at the head-end and remote control center. Four independent receivers integrated into a 1RU 19” casing to supply service for HFC network terminal. Receiver's low noise design, -22dBm receive sensitivity can provide service to farther place. There are two versions of this receiver. HR2040A with LCD on the front panel, HR2040B without LCD. All receivers are temperature tolerance type can be installed in any network surroundings including out-door type. Both of these two types can adopt SNMP function which can control the front panel to realize optimization work at the head-end and remote installment.
-
HR2080A, HR2080B -
Hangzhou Huatai Optic Tech. Co., Ltd.
HR2080 series HFC 8 ways return path receiver can convert upstream optical signal to RF signal at the head-end and remote control center. 8 independent receivers integrated into a 1RU 19” casing to supply service for HFC network terminal. Receiver's low noise design, -22dBm receive sensitivity can provide service to farther place. There are two versions of this receiver. HR2080A with LCD on the front panel, HR2080B without LCD. All receivers are temperature tolerance type can be installed in any network surroundings including out-door type. Both of these two types can adopt SNMP function which can control the front panel to realize optimization work at the head-end and remote installment.
-
PD9024 -
INSTOCK Wireless Components, Inc
PD9024 is an outdoor, waterproof and weather resistant, IP67 rated, 2 way, 50 ohm, broadband RF high-power power combiner furnished with type N female coaxial connectors. All wireless band frequencies in the range from 698 to 2700 MHz are covered with best in class RF performance. Max microwave input power levels to 100 watts can be handled in power divider splitter applications. For non-coherent signals, up to 20 watts can be handled through each port. With coherent signals, up to 50 watts can be handled through each port. See 2 way high power combiner input rating tables for more info.
-
PD9124 -
INSTOCK Wireless Components, Inc
PD9124 is an outdoor, waterproof and weather resistant, IP67 rated, 2 way, 50 ohm, broadband RF high-power power combiner furnished with SMA female coaxial connectors. All wireless band frequencies in the range from 698 to 2700 MHz are covered with best in class RF performance. Max microwave input power levels to 100 watts can be handled in power divider splitter applications. For non-coherent signals, up to 20 watts can be handled through each port. With coherent signals, up to 50 watts can be handled through each port. See 2 way high power combiner input rating tables for more info.
-
PD9026 -
INSTOCK Wireless Components, Inc
PD9026 is an outdoor, waterproof and weather resistant, IP67 rated, 2 way, 50 ohm, broadband RF high-power power combiner furnished with type N female coaxial connectors. All wireless band frequencies in the range from 698 to 2700 MHz are covered with best in class RF performance. Max microwave input power levels to 100 watts can be handled in power divider splitter applications. For non-coherent signals, up to 20 watts can be handled through each port. With coherent signals, up to 50 watts can be handled through each port. See 2 way high power combiner input rating tables for more info.
-
PD9126 -
INSTOCK Wireless Components, Inc
PD9126 is an outdoor, waterproof and weather resistant, IP67 rated, 2 way, 50 ohm, broadband RF high-power power combiner furnished with SMA female coaxial connectors. All wireless band frequencies in the range from 430 to 470 MHz are covered with best in class RF performance. Max microwave input power levels to 150 watts can be handled in power divider splitter applications. For non-coherent signals, up to 5 watts can be handled through each port. With coherent signals, up to 75 watts can be handled through each port. See 2 way high power combiner input rating tables for more info.
-
Ironwood Electronics
*Package-size PCB footprint: Since the PCB footprint of G80 is identical to the package, only one PCB design is required, enabling a seamless transition from test and validation through production and reducing overall cost of test*Low insertion force: Unique contact design reduces the insertion force required to insert and retain higher-ball-count packages safely and securely within the test socket*No lid required: The package snaps directly without a lid, enabling easy probing, scoping and troubleshooting the topside of the device*Excellent signal performance: A short signal path achieves low inductance and low insertion loss, providing a nearly invisible electrical connection
-
NI RFSA Soft Front Panel -
NI
The NI RFSA Soft Front Panel helps you quickly view and analyze RF signals using PXI hardware from National Instruments. The soft front panel features built-in measurements such as third-order intercept (TOI), complementary cumulative distribution function (CCDF), adjacent channel power ratio (ACPR), occupied bandwidth (OBW), channel power, and transmit power. With these one-button measurements, you can quickly measure, display, and store results, which makes NI PXI instruments ideal for characterization and validation environments. You can also use the NI RFSG Soft Front Panel for generating continuous waveform (CW) or modulated RF signals.
-
HMC7748 -
Analog Devices Inc.
The HMC7748 is a multistage power amplifier (PA) that provides 25 W of saturated output power across the band of 2 GHz to 6 GHz. It draws 0.7 A from a 12 V supply and up to 4 A from a 28 V supply. Input signals of as much as −8 dBm are acceptable, and the module has small signal gain of 60 dB. The 12 V supply is regulated internally and generates the negative voltage required for the gate bias. Built-in bias sequencing prevents the drain voltages for the amplifier stages from being applied without the negative voltage present, which protects the amplifiers if 28 V is applied without 12 V supply applied.
-
PCI-8124-C -
ADLINK Technology Inc.
PCI-8124-C is a 4-CH trigger board which is suitable for advanced line scan application which need high line rates. PCI-8124-C has internal FIFO to realize the high speed position compare and trigger pulse output. For this application, ADLINK proposes you can use PCI-8134 and PCI-8124-C together to gain the advantage of motion control and high speed trigger function. For position compare, PCI-8124-C provides two method: linear function or variable interval. PCI-8124-C also provides the variety of mapping function between comparator and trigger output. The comparator condition can be associated with latch signal, TTL input and EA/EB signal.
-
Adaura Technologies
RF leakage through Ethernet and USB cables can destroy even the best RF enclosures and chambers. The need for filtering in the ever congested RF environment requires special filters that can pass USB 2.0 and 10/100/1000 Mbps Ethernet signals and filter out unwanted higher frequencies such as cellular and WiFi. The Adaura Technologies USB/Gigabit Filters provide one GigE and one USB 2.0 pass-through connections while filtering out other RF up to 8GHz. It has a small form factor to allow easy installation. It is a most cost effective solution for a clean chamber set up. In a typical chamber, WiFi signals are reduced to <-100dBm with this filter installed.
