Showing results: 3496 - 3510 of 8180 items found.
-
Laurel Electronics, Inc
Laureate TM Series serial output transmitters can be jumpered for two signal levels: RS232 or RS485. Two serial protocols are selectable in software: Modbus or Laurel's Custom ASCII.Modbus protocol operation is fully compliant with the Modbus Over Serial Line Specification V1.0 (2002) for 2-wire, half-duplex connection.
-
EMIC Corporation
The principle of the eddy current is applied to measure the distance without contacting an object. This measuring method is widely used in the industry for detecting abnormal vibrations of rotating shafts or ironwork in a production in line. The highly accurate signal conditioning for providing the analog voltage being linearly proportional to displacement can be made easy.
-
Thorlabs, Inc.
Thorlabs' Optical Spectrum Analyzers (OSAs) perform highly accurate spectral measurements. Compatible with fiber-coupled and free-space light sources, these compact benchtop instruments suit a wide variety of applications, such as analyzing the spectrum of a telecom signal, resolving the Fabry-Perot modes of a gain chip, and identifying gas absorption lines.
-
Liquid Instruments
Moku:Phasemeter is based on a digital phase-locked loop architecture and can track the phase, frequency and amplitude of two signals from 1 kHz to 200 MHz. Measure phase changes of less than a millidegree with a sensitivity of better than 100 nanocycles/√Hz. Record frequency fluctuations with zero dead time.
-
Appointech, Inc.
The fiber-optic coaxial PIN-TIA receiver module is designed for SONET/SDH fiber-optical communicationnetworks, using reliable InGaAs PIN photodiode (PD) highly integrated with low noise transimpedence amplifier(TIA) to convert a long wavelength input optical signal into a differential (or single) output. It is a highly reliablemodule with excellent performance.
-
ORTEC
The primary function of a preamplifier is to extract the signal from the detector without significantly degrading the intrinsic signal-to noise ratio. Three basic types of preamplifiers are available: the current-sensitive preamplifier, the parasitic-capacitance preamplifier, and the charge-sensitive preamplifier. ORTEC manufactures a preamplifier to fit your detector, your application, and your budget.
-
Model 272A -
Telebyte, Inc.
FEATURES: Data Rate to 2.5 MBPS; Full Duplex TD and RD; ST Connectors; Extends RS-422 Network up to 2 km (6,600 ft). The Model 272A provides the capability of performing an interface conversion between full duplex, RS-422 signals and their equivalent for fiber optic transmission.
-
Prime BSI Express -
Teledyne Photometrics
The Prime BSI Express Scientific CMOS (sCMOS) is designed on a compact platform optimized for integration and delivers the perfect balance between high resolution imaging and sensitivity with an optimized pixel design, USB 3.2 Gen 2 connectivity and near perfect 95% Quantum Efficiency to maximize signal detection.
-
ICS Electronics
*ICS's Serial to Digital Interface boards provide the user with digital IO signals that can be user configured to match virtually any application. Both boards are available with high power relay drivers and with optional firmware designed to simplify switching applications.*All boards are designed for mounting inside a chassis.
-
8 Channel (74HC4051) -
SparkFun Electronics
The SparkFun Multiplexer Breakout provides access to all pins and features of the 74HC4051, an 8-channel analog multiplexer/demultiplexer. The 74HC4051 allows you to turn four I/O pins into eight multifunctional, individually selectable signals, which can be used to do everything from driving eight LEDs to monitoring eight potentiometers.
-
Cab Driver -
Whirlwind Music Distributors, Inc.
The CAB DRIVER is a test device for checking the operation of the speaker components within enclosures. A pink noise signal source is sent through pushbutton selectors to an assortment of speaker connectors, including Speakon NL8 and NL4, 1/4" TS and banana jacks. Speaker/ Polarity/ Impedance/ Pink Noise Generator
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
This page shows vibration sensors for special applications.The Seat Pad Accelerometer Model KS963B100-S was developed for measuring whole body vibration transmitted by driver seats of building machines and other vehicles in compliance with ISO 10326-1 and ISO 7096. The sensor has an IEPE output for robust signal transmission.
-
MacArtney A/S
The MacArtney Group depends on the support of a number of major cable manufacturers to supply a range of cables that are designed, manufactured and tested to meet the highest demands of the underwater technology industry. The product range includes TV, signal, instrumentation, fibre optic, ROV, oceanographic geophysical, telecommunication, fishery and sonar cables.
-
Dexter Research Center, Inc.
A low cost solution for non-contact temperature measurements. The sensor is integrated with signal conditioning that reliably produces a calibrated linear digital output in a plug-and-play package having many options. Programmable outputs and flexible power requirements yield a turnkey solution for medical, consumer, commercial and industrial applications.
-
CFP2 -
Eoptolink Technology Inc., Ltd.
Eoptolink CFP2-100GBASE-LR4 / CFP2-100GBASE-ER4 module supports a link length of 10, 20, 25 and 40km kilometers on standard single-mode fiber (SMF, G.652). 100 Gigabit Ethernet signal is carried over four wavelengths. Multiplexing and demultiplexing of the four wavelengths are managed within the device.