Showing results: 4141 - 4155 of 8184 items found.
-
Kuhne electronic GmbH
Is a radio beacon, whose purpose is the investigation of the propagation of radio signals. Most radio propagation beacons use amateur radio frequencies. They can be found on LF, MF, HF, VHF, UHF, and microwave frequencies. Microwave beacons are also used as signal sources to test and calibrate antennas and receivers
-
LCS-3 -
PENKO Engineering B.V.
Load cell simulator particularly useful in a test environment for example to check a program sequence of a controller. The LCS-3 is a simulator used as a substitute for strain gage transducers to generate the precise mV/V signals required in the development , checkout and pre-calibration of signal conditioners, digital and analog readouts and data loggers.
-
780164-01 -
NI
The USB-4431 is designed for sound and vibration measurements. Input channels incorporate integrated electronic piezoelectric (IEPE) signal conditioning for accelerometers and microphones. The four USB-4431 input channels simultaneously digitize input signals. The analog output (AO) channel is ideal for stimulus-response tests and can be synchronized to the AI channels.
-
PCCextend 70 & 75 -
Sycard Technology
The PCCextend 70 socket saver/extender is optimized for the full 33MHz speed of the CardBus interface. Its six-layer controlled impedance construction provides excellent signal integrity. The PCCextend 75 socket saver/extender is similar to the PCCextend 70, but has it's connector mounted on the bottom. When used in conjunction with the PCCextend 70, it allows both slots of a notebook computer to be extended at the same time.
-
EC-501A & EC-501A(G) -
Automation Products, Inc.
Dynatrol® EC-501A and EC-501A(G) Control Unit combines with the DJ and G Series Dynatrol® Level Detectors, including Sealed and Suspended units. Within the Control Units, a SPDT relay is operated from the On/Off signal of the Dynatrol® Level Detector. Simply actuate process control equipment, level alarms or indicator lights from the contacts of this control unit.
-
NI
Digital I/O Adapter Modules for FlexRIO offer up to 54 channels of configurable digital I/O that can interface with single‐ended, differential, and serial signals at a variety of voltage levels. When combined with a large, user‐programmable FPGA, you can use these modules to solve a variety of challenges, from high‐speed communication with a device under test to emulating custom protocols in real time.
-
Revolution -
True North Technologies
The Revolution electronic compass combines a precision 3-axis solid-state magnetometer and a rugged 2-axis electrolytic tilt sensor to provide accurate heading and tilt measurements over a broad range of environmental conditions. The firmware and signal processing algorithms have been refined and improved over three prior generations of electronic compasses to deliver the ultimate in performance from the available sensor data.
-
Model 8063 -
ICS Electronics
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
-
ICS Electronics
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
-
Ultima® X -
MSA
The Ultima X Series Gas Monitors with X3 Technology bring the power of multi-sensing, signal boost and ModBus output to the Ultima X line of MSA gas monitors. The units are crafted from either stainless steel or NEMA 4X-rated plastic, and our patented SafeSwap sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification.
-
FEMTO Messtechnik GmbH
Ultra-wide bandwidth from 10 kHz up to 2.5 GHzGain up to 60 dB (x 1,000)Transimpedance gain with photodetectors up to 50,000 V/AVery low input noise down to 310 pV/√Hz (6.2 pA/√Hz)Integrated DC-current path for biased photodetector applicationsTwo identical signal outputs (HSA-Y series)DC-monitor output (HSA-Y series)
-
Model KM 963 G -
Kusam Electrical Industries Limited
“KUSAM-MECO” Grain Moisture Meter Model KM 963-G incorporates the latest technology for determining the moisture in grains. It complements the family of moisture meters for wood(KM 963) & Paper (KM-963P). It can determine the % moisture in Wheat, Paddy, Rice & Corn. The Instrument consists of sensor which senses the moisture in grains & a microprocessor computes the signal in % which is displayed on the LCD. It is very simple to operate.
-
Model PZD2000A -
TREK, INC.
The Trek Model PZD2000A is a wide bandwidth high-voltage power amplifier used for precision high power applications. This new addition to the Trek power amplifier product line is designed to provide precise control of output voltages in the range of 0 to ±2 kV DC. Features include an output current range of 0 to ±400 mA and an excellent large signal bandwidth capability.
-
Renesas Electronics Corp.
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
OP-SB89G -
LINEEYE Co., Ltd.
OP-SB89G is an expansion board for Ethernet LAN (supporting Gbit), inserting into a slot of portable communication analyzer (LE-8200A/LE-8200). It is a stand-alone LAN analyzer, exchanging the measurement board and line state sheet for LAN signals. The monitor function measures data at real time by simply connecting the LAN cables. The packet generation function transmits frames from the analyzer at wire rate.