Filter Results By:
Products
Applications
Manufacturers
Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
product
Perseus SDR HF Receiver
PERSEUS is a VLF-LF-HF receiver made by Microtelecom is based on a outstanding direct sampling digital architecture. It features a 14 bit 80 Ms/s analog-to-digital converter with an exceptional 76 dB SNR (BW = 40 MHz), an high-performance configurable FPGA digital down-converter with an up to 1 MS/s output sampling rate and a 480 MBit/s, high-speed USB 2.0 PC interface. Unlike in lower class direct sampling receivers, the PERSEUS RF analog front-end has been carefully designed for the most demanding users and includes a 0-30 dB, 10 dB steps attenuator, a low-loss 10 bands pass-band RF preselector filters bank, and an high dynamic preamplifier with a top-class input third-order Intercept Point of more than 30 dBm. The resulting third-order dynamic range is 103 dB for SSB signals (2.4 KHz BW) and 107 dB for CW signals (500 Hz BW).
-
product
Phase Detector Modulevalon
4002
sThe Valon 4002 Phase Detector module Independently measures both Gain/Loss and Phase between two signals. It is a perfect complement to all our Frequency Synthesizer modules and ideal for many experimental RF applications. The 4002 enhances the performance of the AD8302 base core.
-
product
Phase Detectors
CD series
The CD series is a phase detector module. It is possible to detect small level signal and signal buried in noise.
-
product
Phasemeter
Moku:Phasemeter is based on a digital phase-locked loop architecture and can track the phase, frequency and amplitude of two signals from 1 kHz to 200 MHz. Measure phase changes of less than a millidegree with a sensitivity of better than 100 nanocycles/√Hz. Record frequency fluctuations with zero dead time.
-
product
Phase Meter
SD1000
The SD1000 phase meter offers superb accuracy with a wide range of signal conditions. Conventional phase meters are easily upset when small levels of noise and distortion are present - the result is often unstable and incorrect phase readings. The SD1000 overcomes this by using Discrete Fourier Analysis (DFT), this process rejects any noise and distortion without the need for tracking filters.
-
product
Phase Noise and Allan Deviation Test Set
5125A
The 5125A makes accurate phase-noise measurements on signals from 1 MHz to 400 MHz, covering the full range of the most commonly used frequency references. The 5125A, which requires absolutely no configuration, displays measurement results seconds after the Start button is pressed.
-
product
pH / mV Transmitter
DO9403T-R1
The DO9403T-R1 pH transmitter converts the output of a pH electrode, with temperature compensation, into a 4÷20 mA signal.
-
product
Photodiode
A high sensitivity receiver in a fiber pigtail coupled package, it includes a high speed InGaAs avalanche photodiode with a high gain TIA in a hermetically sealed coaxial package. It incorporates an LC/UPC pigtail and a flexible printed circuit (FPC). The signal GND and a receptacle are electrically isolated in this APD receiver.
-
product
Photodiodes
Photodiodes are a type of detector, devices that generate an electrical signal when illuminated by light. ACP offers a variety of different types of photodiodes, including InGaAs PIN photodiodes.
-
product
Photometric Radiometric Transmitters
HD2021T Series
The serie HD2021T allows to convert photometric and radiometric quantities, such as illuminance (Lux) and irradiance (W/m²) in the UVA, UVB, UVC spectral regions and in the 400 … 1050nm band, into a 0 …10Vdc voltage signal. The series is suitable to be installed either indoor and outdoor.
-
product
Photometric Radiometric Transmitters
HD2021T6 / HD2021T7
The transmitters allow converting the photometric quantity “equivalent veiling luminance” – HD2021T7 – or a photometric quantity Luminance (cd/m2) – HD2021T6 – into a current (4…20 mA) or a voltage (0…10 V) signal according to the version chosen. If the acquisition station is far from the probe (>50m), it is necessary to use the current output version.The probe is used for the control of street lighting, in particular, the measurement of equivalent veiling luminance is essential to determine the threshold luminance at the entrance of the tunnels (UNI 11095:2011).
-
product
Photonics
Precision fiberoptic and free-space interfaces provide high-speed, low-jitter and low noise signal conversion, and transport of analog and digital signals.
-
product
PicoBuck LED Driver
The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8860 part.
-
product
Pico-ITX SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, LVDS And LAN
PICO313
The PICO313 features the Intel® Pentium® processor N4200 or Celeron® processor N3350, aim at the entry-level market. It runs fanless, supporting +12VDC power input, slim I/O and extended temperature range. The Pico-ITX motherboard has one 204-pin DDR3L-1867 SO-DIMM socket with up to 8 GB memory. One full-size PCI Express Mini Card slot with support of mSATA and one half-size PCI Express Mini Card slot are available on the rear side of the board. Additionally, a pair of expansion connectors provides signals for one PCIe lane, one LPC, one DDI, four USB 3.0 ports, one SMBus, and one HD audio to meet different communications needs.
-
product
Picowatt Photoreceiver
Series PWPR-2K
Picowatt photoreceiver series PWPR-2K with switchable gain (109 V/A, 1010 V/A) and a bandwidth from DC to 2 kHz is the perfect choice for cw-measurements, time resolved signal acquisitions and highly sensitive modulated measurements.
-
product
PID Controller
ZET 7190-R
ZET 7190-R — PID controller on CAN bus. It is used in automated systems for control signal forming.
-
product
PLC Input Modules
The DATEXEL DAT6000 series is a unique device designed to add analog inputs to a digital PLC with a few simple instructions. Downloaded into a standard PLC it is possible to acquire analog signals. The PLC will be able to read a 16 Bit digital input equal to the analog signal. The input, output and power supply are isolated from each other. The DAT6000 can linearize , filter and convert the input signal.The DATEXEL DAT6011 converts two voltages -50 mV to 50 mV, -100 mV to 100 mV, -500 mV to 500 mV or -1000mV to 1000mV or thermocouples K Type, J Type, S type, B type, R type, E type, T type and N type to a digital PLC.
-
product
PLC's
The EPL101 PLC is a circuit board OEM PLC. The EPL101 has 4 analog inputs, 7 digital inputs and 2 inputs for Encoders. It has 6 relay outputs, 5 that are rated for 5 Amps and 1 relay rated for 16 Amps. It also has an analog output 0-5 Volts. The outputs can be simple on off or P, PI,PID or PD control. The EPL101 accepts inputs from K, S, T, R, J or E type thermocouples, Pt100, Ni100 RTD'S. NTC10K thermistor inputs. The EPL101 also accepts inputs from sensors with 4-20mA, 0-20mA, 0-20mV or 0-1V signal. It also has 6 digital PNP inputs up to 1 Hz and 2 NPN inputs up to 2 K Hz.
-
product
Plug-On Transmitter
HMa
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. Phantom power is selectable at 5, 15 and 48 volts, or can be turned off for use with dynamic microphones and line level signal sources.
-
product
PMC-BiSerial II-NG1
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
-
product
PMC Interface Card
CPCIC-MA4
The CPCIC3/6-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
product
PMICs For Automotive
Renesas' automotive product portfolio includes integrated power management ICs (PMICs) that support the power requirements of most central displays as well as the power requirements of most combinations of image sensor, image signal processor, and encoder technology for rear and surround view HD automotive cameras, driver monitoring cameras, HD dash cams, rear seat entertainment, and virtual dashboards.
-
product
PON Power Meter
Optical Wavelength Laboratories
Up to 100 data points can be stored in internal memory, which can be recalled on the LCD display at a later time.Up to 10 threshold sets can be stored in internal memory, allowing users to measure PON signals against pre-set thresholds based on different measurement points in the FTTH network.
-
product
Portable Analyzer and Calibrator
ECD’s portable analyzer and calibrator product lines are a simple convenient way to obtain fast, accurate pH and ORP measurements. They provide a milliVolt output signal for fast field analysis of samples, calibration verification, or trouble-shooting of installed sensors.
-
product
Portable Calibrator
MC141
Voltage range from 0 to 750 V DC/AC with uncertainty 0.01% Current range from 0 to 2 A DC/AC with uncertainty 0.02 % Calibrated sinusoidal output signal DC - 1kHz. Set standard resistors from 10 Ohm to 100 MOhm in decade values with uncertainty 0.02 %. TC temperature sensor simulation R, S, B, J, T, E, K, N in range from -250 oC to 1850 oC
-
product
Portable DAQ & Signal Analyzer
ObserVR1000
Vibration Research Corporation
Collect data with the press of a button using the battery powered ObserVR1000 hardware and a mobile interface. Stream to the SD card while running other test modes, or use independently as a field data recorder and analysis package.
-
product
Portable Monitoring Receiver and RF Recorder
IZT R3301
The IZT R3301 is a portable receiver with an integrated server for data recording. The receiver is optimized for recoding of RF signals in frequently changing environments. The RF characteristics of the IZT R3301 are identical to the IZT R3000 series. # HF-VUHF-SHF receiver# frequency 9kHz...3GHz (3...12GHz option)# continuous spectrum recording of 24 MHz bandwidth, IQ recording with 20 MHz
-
product
Portable Multiple Frequency Signal Generator
PSX-6C
Matrix Test Equipment Incorporated
The Model PSX-6C is a portable, weatherproof Generator of clean, unmodulated, crystal- controlled, amplitude-variable outputs, up to +60 dBmV per channel. The PSX-6C is an improved version of the PSX-6 using enhanced technology and provides carriers that can be adjusted over a linear range of 15 dB.
-
product
Portable Oscilloscopes
ScopeMeter Portable Oscilloscopes take you into territory that standard bench oscilloscopes cant readily withstand, harsh, hazardous and dirty industrial environments. These hand-held instruments combine the performance of a bench oscilloscope with a multimeter and paperless recorder for installing, commissioning and maintaining industrial and electronic equipment out in the field. Fluke ScopeMeter test tools use a unique Connect-and-View mode to automatically and continuously setup the oscilloscope making them easy to use even on complex signals.
-
product
Portable Signal Conditioning System
SCS-800
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.
