Showing results: 5596 - 5610 of 8181 items found.
-
NI
The C Series Voltage Output Module helps you update analog output models that feature overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. This module includes up to 16 channels. Some models include a channel-to-earth ground double isolation barrier for safety and noise immunity as well as improved signal quality, and some higher density models conserve chassis space, which leaves room for other measurement types.The C Series Voltage Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
LS2050 -
Lisun Electronics Inc.
LS2050 digital power meter is a new generation intelligent product which adopts digital sampling technology to analysis of the waveform. It has the following features: • Three windows digital display which reduces reading error, intuitive and convenient • Adopts high speed MCU and high precision A/D to control and measurement • All measured data as virtual value, also suit to signal waveform distortion • Fast test • Equipped with RS232 communicate function, can use upper computer software to carry on remote operation, control and read corresponding data, the test data and waveform could be displayed in the PC, Chinese and English operation interface, high intelligent instrument • This instrument provides two kinds of method to calculate total harmonic distortion (THD), IEC and CSA.
-
Datexel
The EPL101 PLC is a circuit board OEM PLC. The EPL101 has 4 analog inputs, 7 digital inputs and 2 inputs for Encoders. It has 6 relay outputs, 5 that are rated for 5 Amps and 1 relay rated for 16 Amps. It also has an analog output 0-5 Volts. The outputs can be simple on off or P, PI,PID or PD control. The EPL101 accepts inputs from K, S, T, R, J or E type thermocouples, Pt100, Ni100 RTD'S. NTC10K thermistor inputs. The EPL101 also accepts inputs from sensors with 4-20mA, 0-20mA, 0-20mV or 0-1V signal. It also has 6 digital PNP inputs up to 1 Hz and 2 NPN inputs up to 2 K Hz.
-
PHD-3001A -
High Power Pulse Instruments GmbH
*Pulse force and pulse sense fixed pitch and flexible pitch RF probing solution for TLP/VF-TLP/HMM on-wafer measurements using Picoprobe™ Model 10*High peak current capability 80 A (100 ns)*DC – typ. 7 GHz bandwidth*Isolated probe-head ground shield for high pulse sense common mode signal rejection*Including fixed pitch replacement probe tip 50 Ω, right, 100 µm pad pitch*Including fixed pitch replacement probe tip 5 kΩ, left, 100 µm pad pitch*Including flexible pitch clamps plus 10-5k(0502)-125-W-1 and 10-50/30-125-W-1 replacement probe tips*True coaxial high-resolution 80:1 rotary probe-head for accurate probe tip adjustment
-
USB2251 -
Validyne Engineering
The USB2251 Pressure Sensor Interface provides real-world data acquisition for your PC via the USB port. 8 calibrated variable reluctance pressure sensor inputs are accepted by the USB2251. No external signal conditioning is required.The USB2251 includes a connector panel for sensor cables, calibration constants for each sensor , configuration and data acquisition software. The USB2251 produces a floating-point value for all readings, directly in engineering units.The USB2251 can record pressure readings up to 5000 samples per second. Combined with the fast response of the Validyne VR pressure sensors, the USB2251 is ideal for transient pressure studies. The USB2251 is compatible with the following Validyne variable reluctance pressure sensors: AP10, DP103, DP10, DP45, DP15 DP360, DP215, and DP363. Each sensor is calibrated with the USB2251 at the factory and is ready to make measurements.
-
140BMC/6P -
Aines Manufacturing Corp.
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
Datexel
Datexel manufacture a large range of Trip Amplifiers and Process Limit Alarms that accept universal inputs and provide either relays or NPN or PNP transistor outputs. The DAT5028 is also an isolated signal converter and has a local display with up to 4 relays and is DIP switch programmable. The inputs can be Thermocouples, RTD, mV, mA, Resistance, Potentiometers or Voltage. They can be supplied fully configured set up by PC or DIP switches. The DAT5024 is a trip Amplifier / Temperature limit alarm for RTD's, Thermocouples, Voltage, Resistance and Current with the option of 1 or 2 relay outputs hysteresis and delay timers. The DAT5024 E range is an economical choice with DIP Switch programmable for voltage or current input. Either 1 relay or 2 relays (SPDT) are available with delay timers.
-
MVFL Series -
Shanghai Tarluz Telecom Tech Co., LTD
MVFL series Visual Fault Locators is meet the Class IIIA product, which is the easiest way to identify fibers from end to end and locate polished connector endfaces. Its red laser shines through most yellow-jacketed fibers to help you pinpoint breaks, bends, faulty connectors, splices and other causes of signal loss. The 1mW output power enable the MVFL has a reach of up to 5 km. MVFL seires VFL locates faults visually by creating a bright red glow at the exact location of the fault on single mode (SM) or multimode (MM) fibers. Due to its small size, lightweight and simple but proven design, the MVFL can accompany you anywhere In your pocket or belt pouch in harsh environment
-
FC-3000 -
MCH Instruments Co.,Ltd.
Features:*Frequency measuring range: 0.1Hz to 100MHz in A input, 80 MHz to 3.0GHz in C input.*Period,Total and RPM measurement for input A*9 Digit display with 0.01mHz resolution in 1 Sec (By Ext.Reference signal).*RS-232C serial interface function for communication with computer.*High sensitivity Extemal reference input function(>=1.5Vrms).*Peciprocal technique for high resolution at low counting frequencies .*Self check function executed to perform a automatic self diagnosis of various counter function.*Push-scanning for selecting Function and Gate time.*Low-pass filter(100KHz,-3dB)installed for removing noise signsl in low frequency measuring.*AC/DC coupling function(Selectable AC/CD Coupling)*10:1 Input Attenuation(Selectable×1/×10 Attenuator)*Data hold function
-
ITS-6200 -
Innovative Technical Systems
The ITS-6200 is a versatile 10 MHz laboratory frequency reference useful for synchronizing test instruments to a common standard. Eight outputs are provided, each which can be configured independently as sinewave or logic level square-wave signals. Additionally, CMOS logic levels can be set for 5V, 3.3V, or 2.5V logic family compatibility. A 10 MHz reference input is provided to phase lock the ITS-6200 to an external reference, such as a GPS or Rubidium standard, or cascade multiple ITS-6200 units for additional outputs. The low phase noise and high stability OCXO within the ITS-6200 is suitable for the most demanding applications, whether free-running or phase locked. The compact size and low power consumption makes the instrument highly portable and suitable for AC-powered operation in the lab or battery operation in mobile or field applications.
-
Arduino MKR Vidor 4000 -
Arduino llc
The Arduino MKR Vidor 4000 brings Arduino's ease of use to the work with the most powerful reprogrammable chips that exist: FPGAs. With Vidor you can create a board where all pins are PWM signals controlling the speed of motors. You can capture sound in real time and make a sound effect pedal for your guitar. It is possible to create a real-time computer reading sensor information and sending it to a state-of-the-art monitor or capture video and overlay sensor information on the image that will then later be sent over to a screen. You can connect to the Arduino IoT Cloud and control a complex laboratory machine running a large amount of motors. You could even prototype your own processors inside the FPGA and have it to work in parallel to the other microcontroller on the board. Vidor is a device that invites for experimentation, precision, and high speed computation.
-
STG-06-S1 -
ERAVANT
Full band noise figure and gain test extenders are offered to extend noise and gain measuring capabilities up to higher millimeterwave frequency ranges. These extenders are designed to interface with noise and gain test systems that have an input IF of 10 MHz to 1.6 GHz, such as the industry standard Keysight 8970A/B, N8975A and Maury MT 2075B. The noise figure and gain test extenders include a high-performance, solid-state noise source (STZ series) and a full waveguide down converter (STC series), which consists of a Faraday isolator (STF series), full band mixer (SFB series), frequency multiplier, and IF amplifier. A frequency source with an output signal in the frequency range of 10 to 20 GHz is required as a local oscillator for the down converter. The noise source is automatically powered on and off by the noise figure meter.
-
S-102 -
Notice
The EDFA slot module of FOTS system with built-in power booster EDFA module offers a special function that is able to change the optical signal amplification feature variously, which is followed by user’s driving embedded pump LD freely. The output power of eash pump LD can be controlled separately by the program that is set up by user. When an optimum optical signal amplification particularity is needed, it is made up so that it can be materialized by choosing the Default mode provided along with User mode. More stable application of EDFA is possible through the monitoring of the factors such as in/out signal power, gain, alarm status and pump LD enabled by the application of FPGA processor which makes high speed driving possible. It is also set up that user’s present-time monitoring and control through LCD monitor of system main frame or GUI display for remote control can be possible. Through optimization of amplifier gain, noise figure, and saturated output power, this EDFA module will expand test capabilities in systems, components or sub-assembly manufacturing.
-
LEDRACK-100W192P -
Lisun Electronics Inc.
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
8491 -
Chroma ATE Inc.
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
