Filter Results By:
Products
Applications
Manufacturers
Solenoid
Act as a magnet when current flows through moving an iron core.
- Pickering Interfaces Inc.
product
PXI 50 x SPST Ruthenium Reed Relay Switching
40-140A-021
This range of high density reed relay switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.).
-
product
DC Gaussmeter
GM1-HS
The Model GM1-HS measures the strength and polarity of magnetic fields up to 799.99 gauss. The thin sensor is at the end of a 100 cm flexible cable. The sensor tip is also flexible and can be bent for a variety of situations. The sensor can be held against the surface of a steel part to check for residual magnetism, or it can be bent into an "L" shape to measure inside a DC Solenoid. This meter has a resolution of .01 gauss (1/50 of the Earth's typical field) which is finer resolution than the Model GM1-ST. It is also used to map fields from large magnets (If fields are over 800 gauss, use the Model GM1-ST). The meter has immediate turn-on and updates 4 times a second. There is no setup required, making this the fastest gaussmeter available.
-
product
DC Gaussmeter
GM1-ST
The Model 1-ST measures strength and polarity of magnetic fields up to 19,999.9 gauss. The sensor can easily fit in a .060 inch (1.5 mm) gap and is at the end of a 100 cm flexible cable. The sensor end can be bent if required for a variety of situations. Place the sensor on a magnet face to measure the field. With a resolution of 0.1 gauss, it can measure any tiny variation from magnet to magnet or it can detect if a given magnet has lost even a little strength. Bend the sensor in to a "L" to measure inside a DC solenoid tube. The 5 digit display requires neither auto nor manual range change, making it easier to use than older style 3 or 4 digit meters. Turn on the meter and immediately begin reading fields (updates 4 times per second). There is no setup required, making this the fastest, easiest gaussmeter available.
-
product
Electric Linear Actuators
MaxJac
The MaxJac actuator features a smooth high response ball screw and gear motor and utilizes a proprietary guidance bushing to provide precision smooth linear actuation. Standard equipment includes a 12 volt motor with potentiometer feedback. It is ideal for throttle control, solenoid actuation, and valve actuation in such applications as construction equipment, motor vehicles, marine, and blood infusion pumps.
-
product
High field Superconducting Magnets
Cryogenic Ltd manufactures a wide range of superconducting magnets for research and industrial purposes. A range of standard solenoids between 1 to 22 Tesla is produced, and in addition split pair solenoids in the range 1 to 14 Tesla, with a typical central field homogeneity of 0.1%.
-
product
Magnetic Measurement System
Model 110
The Model 110 Magnetic Measurement System is a very high field version of our industry-standard MESA, designed specifically to measure high-coercivity samples. It uses powerful amplifiers and specially designed water-cooled solenoid assemblies to achieve the magnetic fields required by state-of-the-art material.
-
product
Stationary Decoders
The DS64 Stationary Decoder allows you to install and operate your turnouts directly through any DCC system that has turnout control. The DS64 works with a wide selection of hardware. From solenoid turnout machines to slow motion motors, the DS64 hasn’t met a turnout it doesn’t like. This affordable, easy to install decoder will add another dimension to your operations.
-
product
Water Cooled Active Resistance DC Electronic Load
WRx Series
Utilizing Magna-Power’s new patent pending Active Resistance Technology in combination with the company’s internally manufactured microchannel water-cooled heatsinks, the WRx Series addresses high power DC applications where exhaust heat control is essential. The WRx Series greatly increases power density compared air-cooled alternatives. An integrated solenoid controls the flow of water to avoid condensation. Full power can be achieved using conventional water, with water inlet temperatures up to 25 °C.
-
product
Electro Mechanical Solenoid Switch
Electro Mechanical Solenoid Switches are a type of switch that are used in applications that require remote-controlled or timed transmission line switching. These switches are very useful in operational systems and test setups where they supply a variety of switching combinations.View more Electro Mechanical Solenoid Switch
-
product
Ultra-Slim Safety Door Switch with Solenoid Interlock
SG-B1 Series
Panasonic Industrial Devices Sales Company of America
The SG-B1 Series and the SG-A1 Series are among the world’s thinnest Safety Door Switches. The SG-B1 Series features a solenoid interlock and five built-in contacts. The SG-A1 Series Safety Door Switch comes with three built-in contacts.
-
product
Gas Metering Valves
VARI-VAC
The Tek-Vac Industries' VARI-VAC® is a smooth acting, bellows sealing gas metering valve available with manual, motor driven, solenoid, or electropneumatic controlling actuators.
-
product
Limit Switches
Panasonic Industrial Devices Sales Company of America
Panasonic offers varieties of Timers, Time Switches, Counters, Hour Meters, Solenoids, Temperature Controllers and Limit Switches. For Eco Series Hour Meters and Counters, please refer to Energy Visualization Components page.
-
product
AS-Interface for Hazardous Areas
*I/O modules for field applications with quick mounting technology*Airboxes for the combination of AS-i inputs and pneumatic output valves*Valve position feedback with solenoid actuation*For silo level applications in hazardous areas*Approval for zone 22, category II 3D
-
product
Solenoid Valves
Omega's solenoid valves for fluid control are used for on/off flow control, directional control, and to pilot pneumatic spring return and double acting actuators. Available with AC or DC solenoids.
-
product
Mass Flow Controller
SEC-E Series
This general purpose mass flow controller has a reliable thermal sensor and solenoid valve, allowing you to achieve high-level control of gas flow. A versatile component, the mass flow controller sec-e series can be used in a wide range of industries.Gas flow through the mass flow controller can be controlled over a range of flows: from 10 SCCM to 200 SLM.
-
product
120-600V Solenoid Voltage And Continuity Tester
1865
Peaceful Thriving Enterprise Co Ltd
This solenoid voltage tester has multiple functions. It tests for voltage, continuity and polarity.
-
product
120-600V Solenoid Voltage&Continuity Tester
1867
Peaceful Thriving Enterprise Co Ltd
Test voltage from 120-600V AC/DC polarity and continuity.
-
product
120-600V Solenoid Voltage Tester
1866
Peaceful Thriving Enterprise Co Ltd
Test voltage from 120-600V AC/DC and DC polarity.
-
product
Solenoid Test Systems
The production solenoid test systems are designed to check a high volume of parts each shift, verifying all important parameters of the solenoid.
-
product
Solenoid Tester
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• High Reliability with Proven Design• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility• Integral Statistical Reporting• Test Data May be Stored in Multiple Formats• Two Year Warranty on Electronics
-
product
Voltage & Continuity Tester
Heavy Duty Solenoid Voltage & Continuity Tester - LCD Live Wire and Stud Detector for carpenters and electricians.
-
product
Solenoid Valve Tester
DZ800
Shanghai Aoboor Electric Co., Ltd.
Insulation resistance, HIPOT, coil DC resistance, turn to turn surge tests can be automatically completed in one time. Applicable to electrical performance test of solenoid valves, changeover valves
-
product
Vol-Con® Solenoid Voltage Tester
61-076
*Extremely rugged and reliable*Vibrates when AC voltage is present*Indicates AC/DC voltage level*Replaceable leads with shielded probe tips (IEC61010-031 compliant)*Bright, long-life LED™s and neon indicator lamp*Dual voltage indication for backup safety*2-year warranty
-
product
Production Displays
In a process control environment logging the sequence of events, such as solenoid operations, relay operations, alarms is important. The Production Displays offered by us accepts digital / AC inputs and keeps a track of such events. These are offered with various options where user can programme the names for each event and configure the normally on or off condition.
-
product
Engine Simulator
MS 1118
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
product
Basic Pneumatic Trainer
Unitech Scales And Measurements Pvt. Ltd
It consists of a basic pneumatics kit components for, FRL unit solenoid valve, cylinder etc. This basic pneumatics kit shall be capable of being used to demonstrate to the design, construction and circuits.
-
product
PXI 25 x DPST Electromechanical Relays
40-146-002
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
PXI 50 x SPST Electromechanical Relays
40-145-001
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
PXI 32 x SPDT Electromechanical Relays
40-148-001
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
Relay
40-145-101
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
