Showing results: 2566 - 2580 of 2906 items found.
-
62000D -
Chroma Systems Solutions, Inc.
Chroma 62000D programmable bidirectional DC power supplies have both power source and load characteristics, two quadrant operation, and allows feedback of the power from the DUT. They can be used for testing renewable energy power systems including PV/storage hybrid inverters, power conversion system (PCS) on charging/discharging, and as a battery simulator. The 62000D also is a fit for testing power components used in electric vehicles, such as bidirectional on-board chargers (BOBC), bidirectional DC convertors, and DC-AC motor drivers, and power conversion simulation tests of batteries in both directions.
-
Cuming-Lehman Chambers
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.Near-Field chambers are an excellent alternative to traditional far-field ranges; testing that can be accomplished on a far-field range can be accomplished on a Near-Field test range. This method of testing allows an operator to employ an indoor anechoic test chamber at a reasonable cost and avoid the problems associated with weather and security concerns often encountered when using an outdoor test range.
-
EXC-8000PCI -
Excalibur Systems, Inc.
The EXC-8000PCIe is a PCI Express card supporting up to eight independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The EXC-8000PCIe supports extensive error injection and detection capabilities, IRIG B Time Code input, and can be ordered with an extended operating temperature range of -40ºC to +85ºC and conformal coating. The EXC-8000PCIe is supplied with C drivers, including source code.
-
OTP2 module no003 -
LXinstruments GmbH
The rack serves as the basic framework for your individually designed test system. Various OTP² modules can be installed in the 200 x 60 x 80 cm rack in order to meet the most varied of test requirements.The modular architecture of the OTP (Open Test Platform) is based on a flexible instrumentation matrix, LXI-based sources and measuring devices, combined with a high-quality transfer interface for connecting the test adapters. The systems can easily be expanded with customer- and application-specific functions. We use standardization to build cost-effective systems that still fit your requirements exactly.
-
HMS-3000 -
ECOPIA
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
Excelitas Technologies Corp.
Omniblock® X-ray generators from Excelitas Technologies integrate the high-voltage source and X-ray tube into one consolidated housing. This design configuration eliminates the high-voltage cables and connectors reducing cost while improving system design flexibility and streamlining integration. They are specifically designed for generating X-rays in static or rotating applications using proven designs of up to 180 kV and 2.4 kW. Typical applications for Omniblock X-ray generators include baggage screening, medical imaging, food inspection, industrial analysis and many other cost-sensitive and space-constrained X-ray applications.
-
Magpie -
LXinstruments GmbH
LXinstruments Magpie is a user-friendly evaluation and data mining application for our test database. The data to be evaluated can be preselected via complex, easily configurable filters. Based on the selected data, it is then possible to create reports and perform statistical evaluations as well as machine capability analyses. The graphical GUI supports easy administration of the database by authorized users.The LXinstruments Magpie evaluation licenses are always linked to the data source, which would generally mean a test system. The test data generated by the test system will be marked as available for evaluation while it is stored in the database.
-
Ametek Scientific Instruments
An impedance analyzer is a device that uses a programmable AC voltage / current source, together with voltage and current measurement circuits, to characterize sample impedance over a wide range of frequency. An example of this being the world famous Solartron Analytical 1260A Impedance Analyzer that provides EIS impedance characterization over more than 12 decades of frequency from uHz to tens of MHz. Impedance Analysis characterization is a key technology that enables new materials development for semiconductors, smart-materials, ferroelectrics, piezo-electrics, solid oxide, solid electrolytes, ceramics, polymers, OLED and many more materials.
-
ProPlex IQ -
TMB
Ethernet tester for entertainment production applications. Designed with input from production and staging professionals as an all-in-one device, it provides feedback and analysis on any Ethernet protocol, as well as network troubleshooting. It can act as a DMX cable tester, DMX receiver/transmitter, DMX timing analyzer, DMX recorder, RDM controller, or a bidirectional Ethernet-DMX gateway. It is also a PoE tester that can determine the capabilities of any connected PoE source. Finally, it can check SMPTE timecode or act as an LTC receiver/analyzer, and LTC transmitter, and users can use it to update Solaris/ProPlex firmware without a PC.
-
ZRS-4H -
Lisun Electronics Inc.
• Test Gas Source: Gas or Liquefied Petroleum Gas (Suggestion: Use good quality gas if possible) • Burner inner diameter: ￠9.5±0.5mm, about 100mm long with air adjusting hole • Height of flame: Can be adjusted from 20 mm to 100 mm according to the standard requirement • Applying time of flame: Burning time can be adjusted from 0 to 99 minutes 99 seconds • Test process: Automatic control • Inner volume: 0.05m³ • Material: Stainless steel or iron plate spray • Power: AC 220V; 50Hz/5A
-
778835-01 -
NI
The PCI-6515 is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
PZ2100A -
Keysight Technologies
The Keysight PZ2100A is the precision source / measure unit (SMU) mainframe that uncompromisingly and densely integrates 20 SMU channels into valuable 1U height, full width, rack space with flexible module options at their best performance. It supports a variety of resources such as the Keysight PZ2110A Precision SMU, PZ2120/21A High-Speed SMUs, and PZ2130/31A High Channel Density SMUs with multiple functions such as pulser and digitizer, as well as precise voltage / current sourcing and measuring to adapt to a wide range of application requirements. The PZ2100A has 4 slots and allows any mixed module configuration for flexible scalability.
-
N6782A -
Keysight Technologies
The Keysight N6782A is a source/measure unit (SMU) designed specifically for advanced functional testing of a device. The ability to modulate the output up to 100 kHz along with capability to source and sink current (2-quadrant operation) makes the N6782A a perfect fit for advanced functional test of a variety of devices such as DC/DC converters, power management units, power amplifiers, and power management ICs. The input stage of the DUT can be stimulated by the fast sourcing and waveform capabilities. While the output stage can be loaded down and measured with the electronic load capabilities, providing a total test solution.
-
DAQe-2500 Series -
ADLINK Technology Inc.
ADLINK DAQe-2500 series are high-speed and high-performance analog output multi-function DAQ PCI EXpress cards. The devices are able to update up to 8-CH, 12-bit analog outputs simultaneously at sustaining 1 MS/s. The reference sources and the output polarities are programmable on per channel basis, combining with the multiplying DAC architecture, ADLINK DAQe-2500 series DAQ cards can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees the CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory.
-
Model 7190 -
Pentek, Inc.
- Simultaneous synthesis of up to 5 different clocks- 8 SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -125 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 10 MHz- Four quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 500 MHz- Control and status via PCI bus interface
