Showing results: 1216 - 1230 of 2874 items found.
-
271 -
Red Rapids
The Model 271 is designed around the Texas Instruments ADS42LB69 16-bit ADC. The 250 MHz sample clock is supplied by either the on-board frequency synthesizer or an external source. The frequency synthesizer can be phase locked to the local 10 MHz TCXO or an external reference can be used to achieve system-wide phase coherence.
-
277 -
Red Rapids
The Model 277 is designed around the Texas Instruments ADS42LB69 16-bit ADC. The 250 MHz sample clock is supplied by either the on-board frequency synthesizer or an external source. The frequency synthesizer can be phase locked to the local 10 MHz TCXO or an external reference can be used to achieve system-wide phase coherence.
-
testIDEA -
iSYSTEM ag
The basic premise behind the development of testIDEA was simple: if our development tools have access to the source code and binary code of an embedded application, and our debug hardware can access all of the internal workings of the microcontroller, surely we can simply test embedded software on the target microcontroller.
-
FMC144 -
Sundance Multiprocessor Technology Ltd.
The FMC144 is an analog-to-digital (A/D) and digital-to-analog (D/A) FMC daughter card that provides four 16-bit A/D channels at 370MSPS and four 16-bit D/A channels at 2.5GSPS which can be clocked by an internal clock source (optionally locked to an external reference) or by an externally-supplied sample clock.
-
80609000 -
6TL Engineering
The single ended active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
80609007 -
6TL Engineering
The single ended active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
Laplace Instruments Ltd.
EMC emissions can be at very low signal levels and pre-amplifiers can help to improve S/N ratio. The low level of emission signals can make them difficult to identify in noisy environments. RF filters are designed to attenuate the major sources of noise, thus making the task of measurement easier.
-
Strain -
Reach Technologies Inc.
Reach Technologies' CAN Strain Sensor Interface sources, conditions and digitizes 8 strain sensor inputs for collection via CAN. The module is ideal for conveniently adding strain data to a distributed CAN network. The CAN Strain Sensor Interface is configurable via a CANopen stack.
-
Shimadzu Corp.
Biomass is considered a prospective new energy source. The dry weight method has been typically used to determine the amount of microscopic algae in biomass. However, Shimadzu proposes a new method, one that is rapid, easy, and accurate, utilizing the TOC-L total organic carbon analyzer.
-
Sealevel Systems, Inc.
Sealevel’s MIL-STD-1553 board-level products, IP cores and custom computer designs are specifically engineered for military, avionics and aerospace applications. Our MIL-STD-1553 products are fully DDC® compatible and can act as a replacement (2nd source) for DDC Enhanced Mini-ACE® devices.
-
RapiTaskZero -
Rapita Systems Ltd.
*Gain insight into your application through scheduling analysis*Locate rare timing events that need attention*Identify bottlenecks in your application by analyzing capacity issues *Compare scheduling algorithms from different RTOSs*Visualize scheduling behavior of libraries without source code
-
GO -
Rotork plc
The gas-over-oil range of pipeline actuators are designed to use pipeline gas as the motive power source. They utilise our robust GH and RH quarter-turn prime movers and are field proven in installations around the world. Control configurations are available to meet virtually any operational requirements.
-
Spectronics Corp
How to pinpoint the exact source of leaks, save money, and protect your business. Our OEM approved fluorescent dyes work as a preventive maintenance system to protect your workers and your business. Our safety products are being utilized in mines all over the world.
-
LSD -
OptCom Company, Ltd
Optcom Diffusion Plates Not Only Diffuse Light But Also are Available in Each Diffusion Level, Which Makes Them Ideal for Adjusting Light Quantity When Measuring Light Source Optical Characteristics. Ideal for light intensity adjustment. 5 types available depending on the degree of diffusion.
-
FES -
Farran Technology Ltd
These frequency extension modules easily connect to the output of your signal generator so you have high-performance source for your DUT characterization activities. Characterize your DUT with the confidence that the superior performance in terms of output power, spurious and harmonic will provide product accurate results.