Showing results: 226 - 240 of 325 items found.
-
Jinan Saicheng Instrument
Saicheng Leak Tester is professionally designed for the leakage tests of packages, bottles & pouches for food, drugs, medical instruments, household chemical products, cars, electronic components, stationeries and other industrial products. The instrument also can be used to test seal performance of specimens after falling and compression tests.
-
Instron
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
Shenzhen Chuangxin Instruments Co., Ltd.
Adjust the impact severity by rotating the knurled cap until the desired energy- value is displayed. Pull the knob slowly out of the device until it locks in place. If moved too fast, the clamp may skip its arrester and will lock at its way back when the pulling-force declines. Hold the device horizontally at it’s housing tube and press the (black) release cone to the specimens plane of impact. The strike is automatically released when the release force threshold is reached.
-
National Technical Systems
Many different loading schemes fall under the broad category of shear testing. Most often performed on small coupons of metals, composites and adhesives, these tests apply force or displacement until the specimen fractures. Single lap, double lap, short beam shear and torsion are typical configurations. All of these tests are designed to characterize materials under shear loading by determining shear-stress/shear-strain curves and material properties, including shear strengths and shear moduli.
-
Qualitest International Inc.
The concrete water impermeability testing system is designed with many different standards in mind including DIN 1048, ISO/DIS 7031, EN-12390-8 & UNI 9533. This impressive piece of machinery comes in different models with either 3 or 6 measuring points and with or without quantitative measurement of water permeability. The supporting structure is very stable and is at a convenient height to allow the easy access. The pans are made out of stainless steel, the specimens are easy to insert due to the clamping device.
-
HST-01A -
Jinan Leading Instruments Co., Ltd.
HST-01A Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated films according to the requirement of relative standards. The seal parameters include heat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
TF164B -
TESTEX Testing Equipment Systems Ltd.
Our Air Permeability Tester determines the resistance of fabrics (woven, knitted and non-woven textile materials) to the passage of air (air flow) under constant pre-set air pressure while firmly clamped in the test rig of selected test head/area.The specimen is loaded to the test area of the instrument easily by means of a pneumatic holder. By pressing down the holder to start the test. The air permeability tester is equipped with a vacuum pump to draw air through an automatic interchangeable test head with a circular opening. The pre-selected test pressure is automatically maintained, and after a few seconds the air permeability of the test specimen is digitally displayed in the pre-selected unit of measure on the touch panel after test the holder is released and the vacuum pump is shut off.
-
TF318 -
TESTEX Testing Equipment Systems Ltd.
SPI Flammability Tester (Vinyl Material), to determine the ignition properties of vinyl plastic film material according to CFR 16 Part 1611 U.S.A. Flammable Fabrics Act for flammability of apparel vinyl plastic film.The rate of burning shall not exceed 1.2 in./s as judged by the average of five determinations lengthwise and five determinations transverse to the direction of processing, when specimen is placed at an angle of 45 degree and expose to the standardized flame (22# fire nozzle, 1/2 inch. In length).
-
GOM GmbH
The ARAMIS 3D Camera is a measuring system for full-field and point-based measurements. With a high resolution of 6 megapixels and a maximum image recording rate of 25 Hz at full resolution, the sensor is suited for medium-fast applications in the field materials and components testing. In a different configuration with a resolution of 2.3 megapixels and a maximum image recording rate of 130 Hz at full resolution expands the range of applications. The ARAMIS 3D Camera is employed in general research and industrial applications for measurements of small specimens up to large objects.
-
Keighley Laboratories LTD
Supports industries such as Aerospace, Nuclear, Automotive, Commercial Fabrication etc.Welding procedure consultancy and approvalWelder qualification test and codingWelding procedure certificationWelder performance qualificationOn site welding invigilationOffers a complete range of destructive and non-destructive testing facilities.Responsible Welding Co-ordinators available for customer supportCAA Weld Specimen SignatoriesCSWIP Approved Inspectors
-
Educated Design & Development, Inc.
1 or 3 actuating device(s) for rocker switches and push- button switches with 2 single-acting pneumatic cylinders each, with air throttle valves to adjust the actuating speed, height-adjustable mounted to holders, with multiple adjustable specimen holders, with safety sockets to connect the specimens to external test voltages and loads1 housing, made of steel, with protective hood1 plug-in unit with front panel for operating the devices.1 Control device for the entire unit:main switch with EMERGENCY OFF function, safety switch for the protective hood, mains cord and fuses1 control device for each actuating device:programmable control unit with exchangeable program modules (containing the "test rhythm") and for adjusting and indicating the test parameters "number of strokes" and "stroke time", start and stop push-buttons, push-buttons for moving manually the cylinder pistons and as actuation indicator for the cylinder
-
VCT-01 -
Veer Electronics
VEER make Toroidal Core Tester VCT-01 is portable & easy to use instrument which is very useful to measure AC magnetic properties of Electrical steel of Toroidal core of different grade and size. We provide Free Computer software along with VCT-01 so, you can create test report of test specimen in computer.
-
cPCI/VME/VME64x -
Kontron
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
IT-1E -
Physitemp Instruments
IT-1E Flexible Implantable Microprobe - For ultra fast measurements and for use on micro-size specimens. Similar to our most popular IT-18 microprobe but the sensor bead is exposed, resulting in the same ultra-fast response time of the IT-23 but with the Teflon™ sheath strength of the IT-18. Time constant 0.005 seconds. Tissue Implantable with a 18 gauge needle (supplied). Rather fragile at tip. Coated in Teflon™. Maximum Temperature 150°C. Isolated. Probe tip diameter .011", sheath diameter .025'' . 3 foot lead.
-
21-25 -
Testing Machines, Inc.
The Auto Density Gradient Column System has become the world’s benchmark for accurate density measurement of small solid polymer specimens using the column method according to ASTM D1505. Offered as a 3 or 6 column version, the built in on-board Microprocessor System accurately calculates the specimen’s density more quickly and more accurately by using the latest linear encoder technology that measures the samples position in the column relative to the calibrated glass marker floats. Once the correct position of the sample is recorded the density is displayed on the LCD screen.
