Showing results: 4876 - 4890 of 6646 items found.
-
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
inTEST Corporation
The primary element of the tester electrical interface is the Probe Pin Ring (PPR). Sometimes referred to as a ‘tower,’ this array of spring-loaded probes can be arranged to provide a controlled impedance path, a low leakage connection, a low inductance arrangement for high currents, or just about any connection characteristic you require. inTEST EMS provides electrical interfaces in various OEM-supported designs, inTEST standards, and custom configurations.
-
Carl Zeiss AG
Is every value precise? The comparability of measurement results has never been more important than in the present era of globalization. The ability to reduce variables to basic units is the fundamental prerequisite to objectively guarantee, increase, and optimize quality. Our calibration service guarantees full correlation to national standards for test equipment of all physical variables – either at our laboratory or on your premises (for measuring tools).
-
Radiometer Physics GmbH
RPG Low Noise Amplifiers are developed and manufactured using the most modern discrete components and thin film technologies, in order to cover the frequency range 50 to 350 GHz. With improved DC-supply and modern semiconductors these amplifiers not only deliver low noise performance but also broad operating bandwidth and gain flatness. These low-noise amplifiers are available as a standard product and on request as customized manufactured product.
-
Russells Technical Products
Our battery test chambers are equipped with safety features conforming to industry safety standards enabling testing to a variety of conditions and specifications including extreme temperature cycling, humidity, vibration, and/or altitude. Russells Technical Products battery test chambers are used in a wide range of battery testing applications including lithium ion, battery packs, lead acid batteries, modules and more.
-
BMP Testing and Calibration Services Inc.
Chemical testing is critical for material and product manufacturing in various industries. It helps identify the contents, composition, and quality of materials used in manufacturing, product development, and other industrial applications. It is also necessary for industries that depend on chemical materials and substances subject to legal regulations, restrictions, standards, and certifications because of their potentially harmful effects for high peroxide strip tests, Chlorine strip tests, the environment, and customers.
-
SpectrOil M Series -
Ametek Spectro Scientific
The latest SpectrOil M series is the eighth generation RDE Optical Emission Spectrometer for elemental analysis in oil and fuel. It is a compact, rugged, transportable and easy to use optical spectrometer that meets military shock and vibration and environmental test standards. The analyzer can be placed in the toughest remote locations around the globe, while still maintaining the laboratory grade accuracy and sensitivity needed for aerospace engine test requirements.
-
OneSpin Solutions GmbH
ASIC synthesis verification from RTL code to final netlist.Systematic design errors, introduced by automated design refinement tools, such as ASIC synthesis, can be hard to detect, and damaging if they make it into the final device. Formal Equivalency Checking (EC) has become a standard part of the ASIC development flow, replacing almost all gate level simulation with a rigorous consistency check between pre- and post-synthesized code.
-
Weshine Electric Manufacturing Co., Ltd
High-voltage Dividers (High Potential Divider) are used to measure voltages and decouple partial discharges in high-voltage test systems. Depending on the specific type, they are used to measure alternating voltage (AC), direct voltage (DC), lightning impulse voltage (LI), and switching impulse voltage (SI) systems. High-voltage dividers by HIGHVOLT comply with the relevant IEC standards. The systems are available for both indoor and outdoor use.
-
VDS-1120DX -
Shenzhen Chuangxin Instruments Co., Ltd.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
Teledyne e2v
Our backside illuminated (BSI) and backthinned Charge Coupled Devices (CCDs) and front and back illuminated CMOS image sensors (CIS) are seen as the gold standard for scientific and quantum imaging in applications in spectroscopy, microscopy, in vivo, x-ray and astronomy. We understand that every imaging application is unique and requires our engineers and scientists to work closely with our customers providing highly tailored imaging solutions.
-
BWA-CAM 20/20 -
Haas Laser Technologies, Inc.
The Beam Waist Analyzer Camera BWA-CAM 20/20 laser beam analyzer system and software enables “real-time” laser beam measurement, analysis and monitoring of high power CW and pulsed lasers.BWA CAM Laser Beam Analyzer system The system complies with the international standards ISO 11146-1 (2005) and ISO 13694 which relate to lasers and laser related equipment and laser beam spatial metrics.
-
Series 420 -
Datum Electronics, Ltd.
Datum Electronics Series 420 PTO (Power Take-Off) drive shaft torque & shaft power monitoring system is designed to monitor and log the torque, shaft speed and transmitted power from all standard PTO shafts.Efficient measurement and monitoring with a PTO shaft power can prove to be a useful tool in research and analysis into the performance of a tractor’s transmission system highlighting efficiency savings, measurement and control.
-
AGREE Series -
ESPEC North America, INC.
For years AGREE chambers have been the workhorses of the environmental test chamber industry. Originally created to meet military test standards, their flexible design has made them suitable for a wide variety of applications. Fast temperature changes of 5 to 25°C/m. are possible, even with significant loads. The chambers have a removable floor, allowing integration with vibration test systems.
-
Hilo Test
The specific EMC requirements in automotive tests take continuously, so that the test waveforms are becoming increasingly complex. As a manufacturer of EMC test simulators and due to the participation in international standardization bodies Hilo test knows the current and future requirements of the automotive industry exactly. The following automotive products are specifically geared to the current EMC requirements in modern automobile, and described in the standards ISO 7637 and ISO 16750.