Showing results: 481 - 495 of 6646 items found.
-
-
-
RF-LAMBDA Inc.
Standard calibration kits used for manual network analyzer calibration
-
-
Advantech Co. Ltd.
Advantech offers different function modules compliant with the PICMG_CPCI-S_0_R2_0 standard.
-
AX93A21 -
Axiomtek Co., Ltd.
*2 PoE-PSE ports comply with IEEE802.3af standard via an internal cable or network cable connected to LAN ports on SBC to power an external PoE device*With an external 12 VDC-in, the 2 PoE-PSE ports are capable of following IEEE802.3at standard
-
ARF TEST
Offers a wide range of standard Test Fixtures that can fit many of your applications and services. From your R & D to your production lines, we have a solution for you.Each products are standard but we can adapt or design your application.
-
TSW400 -
ABB Ltd.
Solid drilled thermowells to satisfy the needs of the Oil & Gas industry. The TSW400 has been designed around the ASME PTC 19.3 2010-TW standard for thermowell stress calculation. Fully compliant with the requirements of this most demanding industry and ASME standards.
-
DDS38 -
Shanghai Powoo Industry Develop Group Limited
The DDS38 single phase static watt-hour meter is designed for measurement of electric energy flowing in one or two directions in households and at commecial customers in single phase 2 wire networks. It complies with IEC61036 standard and is manufactured in compliance with the ISO9001 standard.
-
CAEN S.p.A.
- Programmable FPGA to implement complex logic functions- VHDL coding expertise not required- User-friendly software tools for board programming- Pre-programmed set of standard functions (N1081B/DT1081B)- Different I/Os connectors and standards available (NIM, TTL, ECL, LVDS)
-
CX-T1 -
Shenzhen Chuangxin Instruments Co., Ltd.
Lamp Cap Temperature Rise Test System is according to IEC60360-1998 and GB2512-2001(Standard method of measurement of lampcap temperature rise). It is used to test the working and environmental temperature as well as temperature-rise of the burner and lamp. It meets the requirement of IEC and GB Standards
-
IR-518/301 -
Infrared Systems Development Corp.
The IR-518 Radiation Source provides an accurate, stable source of infrared radiation of known flux and spectral distribution. It can be used as a standard radiation source for the calibration of other laboratory sources, detectors, or other infrared devices requiring calibration against a standard.
-
Kontron
Using a modular concept based on open standards it is common practice in the civil sector to integrate subsystems components from different manufacturers into a single modular system. The SOSAâ„¢ Technical Standard aims at such an interoperability in embedded computing for military applications.
-
Comtel Electronics
VPX technology enables nearly unlimited flexibility when it comes to interconnections between the slots.OpenVPX (ANSI/VITA 65 Standard) addresses this by specifying a set of standard profiles of interconnections. Comtel Backplanes are equipped with Air-/-Plane technology. It extends the life of the existing VPX connector system (MultiGig RT2) and enables unprecedented signal integrity performance which complies with IEEE 802.3bj 100Gb/s standard (4 Ethernet channels via fat pipe).
-
Lansmont Corporation
Lansmont package testing equipment is designed to perform industry standards, such as ASTM, ISTA, ISO, EUMOS and others. Our equipment is compliant with all of the most common ASTM and ISTA package testing procedures. There are individual standards that specifically reference how to perform drop testing, compression testing, side impact testing and vibration testing. In addition to those standards, there are groups of procedures referred to as distribution simulation tests, which incorporate some strategic combination of testing inputs, with the idea of simulating a typical journey through the supply chain. Some of the most common distribution simulation standards that are performed globally are published by ASTM and ISTA.