Filter Results By:
Products
Applications
Manufacturers
Steppers
A device that translates electrical pulses into precise mechanical movement. The output shaft may deliver rotary or linear motion. (www.seanet.com)
- TEAM SOLUTIONS, INC.
product
Motion Control Board, PCI
APCI-8001
*Axis control for 3 servo or stepper motors*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders or SSI absolute encoders*Possibility of extension to a total of 8 axes*Menu-driven test application
-
product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology.
-
product
CCD Foundry Services
Teledyne DALSA Semiconductor’s 150mm CCD process offers surface or buried channel operation at up to 15V with two or three layers of polysilicon and one, two or three layers of metal. A modular processing approach allows our foundry customers to adjust process parameters to meet the most demanding requirements for CTE (>99.999%), charge storage capacity, and dark current (<1nA/cm2). The base process uses 1X projection lithography with 2.5µm design rules, allowing die sizes of up to 100mm X 100mm. Where required, tighter alignment tolerances and smaller feature sizes can be obtained by using 5X lithography, using a mix and match or all-stepper approach. The maximum die size attainable with the stepper is 22mm X 22mm, but larger sensors can be fabricated using stitching.
-
product
Closed-Loop Linear Actuators w/ Stepper Motors, Encoders, and Controllers
A-BAR-E Series
Zaber's A-BAR-E Series products are computer controlled, motorized, ball screw driven linear actuators (electric cylinders) with integrated feedback encoders. They are stand-alone units requiring only a standard 48 V power supply. A built-in encoder allows closed-loop operation and slip/stall recovery features. A manual knob at the end of the unit permits manual control - press and hold to switch between velocity mode and distance mode, turn to move the actuator, and press to stop.
-
product
Closed-Loop Motorized Linear Actuators with Built-in Encoders
BAR-E Series
Zaber's BAR-E Series products are computer controlled, motorized, ball screw driven, linear actuators (electric cylinders) with integrated feedback encoders. A built-in encoder allows closed-loop operation and slip/stall recovery features. Each electric cylinder is wired for use with Zaber's A-Series stepper motor controllers, or they can be used with any 2-phase stepper motor controller through the panel mount DB15 connector. When connected to our A-Series controllers, the actuators are designed to be "plug and play" just like all of Zaber's other products.
-
product
Closed-Loop Motorized Linear Actuators with Built-in Encoders
LAR-E Series
Zaber's LAR-E Series products are computer controlled, precision lead screw driven, motorized linear actuators (electric cylinders) with integrated feedback encoders. A built-in encoder allows closed-loop operation and slip/stall recovery features. Each electric cylinder is wired for use with Zaber's A-Series stepper motor controllers, or they can be used with any 2-phase stepper motor controller through the panel mount DB15 connector. When connected to our A-Series controllers, the actuators are designed to be "plug and play" just like all of Zaber's other products.
-
product
Closed-Loop Motorized Linear Actuators w/ Stepper Motors, Encoders, Controllers
A-LAR-E Series
Zaber's A-LAR-E Series products are computer controlled, lead screw driven, motorized linear actuators (electric cylinders) with integrated feedback encoders. They are stand-alone units requiring only a standard 48 V power supply. A built-in encoder allows closed-loop operation and slip/stall recovery features. A manual knob at the end of the unit permits manual control - press and hold to switch between velocity mode and distance mode, turn to move the actuator, and press to stop.
-
product
Drives
Haydon Kerk and Pittman offer a range of advanced Stepper and Brushless motor drivers to complement its linear and rotary motors. Our Haydon Kerk and Pittman drives are available in many configurations from simple analog controlled single quadrant drives to fully programmable servo motion controllers.
-
product
Econo Motion Controllers
DMC-41x3
The DMC-41x3 motion controller is one of Galil's latest generation, stand-alone motion controller. Compared with the DMC-21x3 controller, the DMC-41x3 offers the following enhancements: 100BASE-T Ethernet, aux RS232 port, USB port, uncommitted analog inputs, up to 15 MHz encoder frequencies, more program memory, and faster sample frequencies. The DMC-41x3 also accommodates the same stepper and servo motor drives used in the DMC-40x0 series and allows two 4-axis 750 W drives to be installed in the 8-axis controller package. The DMC-41x3 is available as a box-level or card-level motion controller. The unit operates stand-alone or interfaces to a PC with Ethernet 10/100BASE-T, or USB. It includes optically isolated I/O in addition to analog inputs and outputs. The DMC-41x3 controller and drive unit accepts power from a single 20-80 VDC source.
-
product
Engine Control
StepGenerator4
*4-axis stepper motor control *Clock and direction signals *Speed up to 100,000 steps / s Positioning range +/- 2,147,483,647 steps *Simple ASCII commands via the serial interface *I2C adapter (master) for controlling external actuators / sensors *40-pin DIP package PCB (600mil / 19mm x 52mm).
-
product
EtherCAT Master Multi-Axis Motion Controllers
DMC-500x0
The DMC-500x0 EtherCAT Controller is Galil Motion Control's newest entry in its latest generation of digital motion controllers. Incorporating all of the features of our flagship Accelera series controller and designed with compatibility and flexibility in mind, the DMC-500x0 allows integration of remote EtherCAT drives into new and existing applications with just a handful of configuration commands. The DMC-500x0 is offered in 1 through 8 axis formats. Axes 1 - 4 can be configured as either local or EtherCAT drives while axes 5 – 8 can be configured for additional EtherCAT drives. Unique to the motion control industry, this ability to mix and match local and EtherCAT drives on the same controller provides increased flexibility for any application. In addition, the DMC-500x0 is fully compatible with Galil’s internal servo and stepper motor amplifiers as well as third party external drives.
-
product
High-Precision XY Stage
V-731
Physik Instrumente GmbH & Co. KG
Reference-class XY stage. Travel range 205 mm × 205 mm (8"). Unidirectional repeatability to 0.1 μm. Velocity to 200 mm/s. Incremental encoder with 10 nm resolution.Optionally with stepper motor.
-
product
Lithography
With steppers for advanced packaging and flat panel display technology, Onto Innovation's latest fleet will meet today's manufacturing challenges head on. Systems are designed to maximize throughput without limited resolution and overlay.
-
product
Load Pull
All Focus tuners use extremely efficient calibration and tuning algorithms and control electronics based on LAN control (iTuner). This is a merger our proven tuner technology with state of the art control electronics to create the latest tuner generation. The on-board micro-processor and tuning firmware form a self-contained and fully calibrated test instrument. The micro-processor inside the tuner accepts ASCII format communication, via an industry standard TCP/IP interface, controls up to nine stepper motors (tuner axes) and executes interpolation and tuning functions for single probe (CCMT) tuners (one probe per frequency range). For tuners with more than one independent probe (MPT) covering the same frequency range to allow for harmonic tuning, external computing power is required, because of the exponentially growing number of combinations of tuner states (slug positions).
-
product
Motion Control Board, PCI
APCI-8001-1
*Axis control for 1 servo or stepper motor*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders *or SSI absolute encoders
-
product
Motorized Linear Actuator
LAR Series
Zaber's LAR Series products are computer controlled, precision lead screw driven, motorized linear actuators (electric cylinders). Each electric cylinder is wired for use with Zaber's A-Series stepper motor controllers, or they can be used with any 2-phase stepper motor controller through the panel mount DB15 connector. When connected to our A-Series controllers, the actuators are designed to be "plug and play" just like all of Zaber's other products.
-
product
Motorized Linear Actuators with Built-in Stepper Motors and Controllers
A-LAR Series
Zaber's A-LAR Series products are computer controlled, lead screw driven, motorized linear actuators (electric cylinders). They are stand-alone units requiring only a standard 48 V power supply. A manual knob at the end of the unit permits manual control - press and hold to switch between velocity mode and distance mode, turn to move the actuator, and press to stop.
-
product
Motors
Pittman and Haydon Kerk motor lines span a wide range of sizes in brushed, brushless and stepper motor technologies. We provide rapid turn-around for prototypes and production orders. Custom designs and special engineering requirements such as special shaft diameters, lengths and mounting flanges are welcome.
-
product
PCI 1-Axis Motion Controller
DMC-1417
The DMC-1417 for the PCI bus is a member of the Econo Series, Galil's latest generation of single-axis motion controllers which are half the size and half the price of multi-axis controllers. The DMC-1417 can handle the most demanding applications with such features as an extra encoder input for electronic gearing, program memory with multitasking, uncommitted I/O and user-selectable stepper or servo motor control.
-
product
RL78 Family Of 8/16-bit Ultra-Low Energy MCUs
RL78/D1x (Automotive Only)
Renesas is introducing the RL78/D1x as an optimized solution for the BRICs and low-end instrument cluster markets. The RL78/D1x is the successor of 78K0/Dx2 or UPD78082x microcontrollers and suited for car instrument cluster, built-in car instrument cluster dedicated features such as Sound Generator, Stepper Motor Controller/Driver and LCD Segment Controller/Driver etc.
-
product
Stepper Motor ,High-Precision Linear Stages,Application for Industry
KSAXXX-13-X
Model: KSAXXX-13-X Stepper Motor ,High-Precision Linear Stages,Application for Industry
-
product
Ultra-High Precision Motorized Vertical Stages
Model: KSAV Ultra-High Precision Motorized Vertical StagesKSAV1010/2030-ZF is new product, wedge vertical stage with.high-resolution, so many advantages: high-stability, high-load and capacity in vertical position,self-locking.applicatin filed: high postion precision,high load capacity,limited space and so onCharacteristic ◆Cross ball screw rail,precion ground ensure resolution, straightness,high load capacity, limited space◆small travel improve resolution◆stepper motor and DB9 interface, choose controller flexibility◆switches ensure safe when operate◆ planning other specification and size
-
product
Z-Axis Drive and Controller
MFC-2000
Applied Scientific Instrumentation
The MFC-2000 has been specifically designed to provide a high resolution and highly repeatable, means of controlling the focus/Z position of the microscope stage. Precise control of the microscope's focus is obtained through the use of a closed-loop DC servomotor employing high resolution encoders for positioning feedback. By using closed-loop control of the focus position, there is no chance that the focus point can be lost as can occur with open-loop stepper motors.
-
product
Stepper Motors
We carry a wide variety of stepper motors including washdown stepper motors for use in wet or dusty environments, 2-phase bipolar motors, integrated stepper motors, and more.
-
product
Motor Control
A product portfolio that offers motor drivers (brushed, brushless, stepper, load & relay) and integrated motor control systems for all your motor control solutions.
-
product
Imaging Scanning Monochromator
H1034
HORIBA Scientific OEM has developed a high-throughput imaging scanning monochromator based on an aberration-corrected concave holographic grating with low stray light and high efficiency. This proprietary layout with single optics design is ideal for imaging for low-light applications. It features a 3-position external filter wheel, TTL drive electronics, 4-phase stepper motor and associated worm/gear 90:1 ratio mechanism, encoded, aligned and focused at factory.
-
product
Exhaust Pressure Controller
EC-5000 Series
The EC-5000 series exhaust pressure controller can maintain a consistent pressure, of the user’s choice, within the chamber. The high-resolution stepper motor and unique butterfly valve ensure a fast, sensitive response to any pressure changes.
-
product
Analog Panel Meters
Jewell Instruments offers a wide range of moving iron, moving coil, and stepper motor analog panel meters in A&M, Emico, Jewell, and Modutec Series.
-
product
Big Easy Driver
The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It's the next version of the popular Easy Driver board.
-
product
Brakes
Power off, fail safe holding brakes. When voltage is applied, the friction disk is released allowing the motor shaft to rotate. Pittman power off brakes are best suited for parking brake applications used to hold a load in position, and are ideal for creating brake motor packages for small frame servo and stepper motors.
