Showing results: 211 - 225 of 513 items found.
-
3DViz -
Luna Innovations Inc.
The 3DViz software provides intuitive 2D and 3D visualization of high-definition sensor data. Software allows strain or temperature data from an ODiSI system to be visualized directly on a 3D CAD model or a 2D image.
-
LWO SERIES -
Transducer Techniques, Inc
The LW0 Series are washer shaped, strain gage based load cells that have been most commonly used in fastener testing and thru hole load applications. Our stocked ranges from 2,400 through 300,000 lb compression are made from 17-4ph heat treated stainless steel and are matched to bolt diameters and their specific load characteristics. Modifications of diameters, thicknesses, or load range to a specific diameter for OEM applications are welcomed. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
92-960-009-M -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate cables with soldered connections. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed when using this product.
-
92-960-009-F -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate cables with soldered connections. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed when using this product.
-
Model 7675 -
Jinan Testing Equipment IE Corporation
Designed for transverse or diametral strain measurement in environmental chambers where the entire extensometer must be exposed to elevated temperatures. These capacitive extensometers may be used up to 700 C (1300 F) without any cooling.
-
EKT-2002FF -
Ektron Tek Co., Ltd.
EKT-2002FF Flexing Fatigue Tester is designed in accordance with ASTM D4482 to test the fatigue life under a tensile strain cycle on different kinds of vulcanized rubber compound to determine the fatigue life at various extension ratios.
-
ZETLAB TENZO -
ZETLAB Company
Software ZETLAB TENZO is included into the delivery scope of Strain Measurement Acquisition Module ZET 017-T8. This software and hardware kit allows you to start taking measurements immediately after device connection and installation of the software.
-
Series 115, 116, & 117 -
Aries
DIP-ER Logic Jumper. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. DIP-ER Logic jumper wiring is point to point. Consult factory for other wiring needs.
-
92-960-004-M -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
92-960-008-M -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
92-960-044-M -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate cables with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
92-960-004-F -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
92-960-044-F -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate cables with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
LCD20 -
Mantracourt Electronics Ltd
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
Tinius Olsen
Extensometers measure strain, the change in length of a specimen divided by the original length (gauge length) of the specimen. Tinius Olsen offers wide range of extensometers based on your testing needs including video, optical and physical contact with specimen.