Showing results: 391 - 405 of 513 items found.
-
Model 3543 -
Jinan Testing Equipment IE Corporation
With over 15 years of proven reliability in the world’s most demanding testing environments, the Model 3543 extensometer is designed to survive in those applications where standard axial extensometers would not. Designed by Epsilon, the Model 3543 was created to survive specimen failure by separating into two halves, thus preventing permanent damage to the module body. During operation, the upper half of the extensometer pulls out of the main body. Tapered measuring beams activate strain gaged flexures within the unit. This unique design allows long measuring ranges, yet retains compatibility with electronics for strain gaged transducers. These models offer high accuracy and are light weight but rugged, with low operating force. They are tension only units.The units have hardened tool steel knife edges. Standard quick attach wires provided with the extensometer work on flat specimens up to 12 x 31 mm (0.5 x 1.25 inch) and on rounds up to 25 mm (1 inch) diameter. Optional quick attach kit wire forms are available for use on larger samples. See Model 3542L for long gauge lengths with smaller measuring ranges.The Model 3543 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Model 3800 -
Jinan Testing Equipment IE Corporation
The main body of this unique extensometer remains stationary during testing, held in position by the adjustable magnetic base included. Only the very light, small traveling heads move as the sample elongates during a test. These attach to the sample with small spring clips. Each head pulls a cord out from the extensometer as the head moves. These models use high precision, low friction potentiometers, and, as a result, have a wide range of factory selectable outputs. The extensometer is driven by an excitation voltage and has output proportional to the input. They can be provided with high level outputs (approximately 2-8 VDC) or ones that mimic strain gaged devices (2-4 mV/V). When set to mimic strain gaged extensometers, the Model 3800 can be used with virtually any signal conditioning electronics designed for strain gaged sensors. The potentiometers employ a hybrid wire wound around conductive plastic, which provides excellent long term stability. The output from the extensometer is readily interfaced with most existing test controllers, and may be directly input to data acquisition systems and chart recorders. Please let us know at the time of order what type of output and connector you require.
-
Campbell Scientific, Inc.
Many Campbell Scientific vibrating-wire peripherals enable dataloggers to read vibrating-wire sensors (also known as vibrating-wire or vibrating-strip transducers). These sensors measure strain, load, pressure, and water level, and they output a frequency signal generated by a vibrating filament. Campbell Scientific also offers vibrating-wire dataloggers that read the sensors directly.
-
Futek Advanced Sensor Technology, Inc.
The Rotary Shaft to Shaft Torque Sensor category has Torque Sensors which are used in slip ring and non contact rotary torque measurements. The most common utilization for these models is for inline/reaction applications, where measurements can be made in both clockwise and counterclockwise directions. The Rotary Shaft to Shaft Torque Sensors are CE certified and utilize a bonded metal foil strain gauge. As with most FUTEK products, we will gladly work with you to customize or modify our Torque Sensors to meet your precise needs.
-
410114014 -
Virginia Panel Corporation
Enclosure, G12, Front Mount, 4 Cable Clamps, 6"x 18" x 12"Includes 4 cable clamps on the back end that eliminate the need for strain relief. When in open position- cable clamps permit removal of the stiffener bar so that installation or removal of cables may be performed without unplugging patchcords from the assembly. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
EKT-2102DF -
Ektron Tek Co., Ltd.
EKT-2102DF DeMattia Flexing Fatigue Tester is designed in accordance with ASTM D430 and D813 to test the repeat bending strain and flexing on different kinds of vulcanized rubber compound. After Test, the fatigue testing equipment can determine the difference of testing compund such as deformation, elongation, hardness, etc. under different temperature environment in certain of time.
-
Model 4030 -
Jinan Testing Equipment IE Corporation
The Model 4030 extensometer uses a special LVDT-like sensor to measure strains on samples submersed in water or other compatible liquids. The unit is provided with the signal conditioning electronics. The extensometer is a semi-custom design, which is available in smaller measuring ranges up to 5 mm (0.2 inches). Clip-on (COD) style designs are also available.
-
ESPP-MIT1 Sensor -
ES Systems
ES Systems has developed a series of strain gauge pressure transmitters featuring very good accuracy at a low cost. Each module is based on an all-welded hermetically sealed structure in a single stainless-steel piece. The ESPP-MIT1 is a medium isolated pressure sensor suitable for gas or fluid pressure measurements in harsh industrial or HVAC environments.
-
2518/2519TDIN -
Sensoray Co., Inc
8 or 16 differential thermocouples, RTD's, strain gauges, thermistors, resistance, 4-20 ma, or voltage inputsIncludes screw terminals for field wiring10-Base-T Ethernet server with embedded TCP/IP stackIncludes interface DLLSingle supply operationEach channel is software programmable for sensor type, gain, low-pass filtering, scan rateOptional NEMA Enclosure
-
Instron
The Instron model XL (long travel) extensometer is a precise device for measuring strain in highly extensible materials such as elastomers, semi-rigid plastics and films. Designed for use with electromechanical testing instruments, Instron XL units can be used to measure specimens elongation's up to 10 in or 250 mm. An optional of 15 in or 375 mm travel is also available.
-
1RA370 -
Le-tehnika, d.o.o.
Include: *Multi network cable tester for RJ45 (UTP / STP) and BNC*Modular crimping tool*LSA insertion tool*Cable stripper and cutter*30 units of RJ45 (8p8c) modular plugs*30 units of RJ11 (6p6c) modular plugs*24 units of colour strain relief*Comonents pocket*Zipper vinyl case
-
Krohn-Hite Corporation
Our DC Source/Calibrators are designed for a typical applications such as the design, check and calibration of high speed, high resolution A/D converters; design and certification of high speed data logging and process control systems; calibration of digital voltmeters and multimeters; as an “IMBEDDED STANDARD” and/or simulator; design, testing, simulation and certification of thermocouples, strain gages and transducer instrumentation.
-
Datum Electronics, Ltd.
Cargo Hawk is a non-intrusive SOLAS compliant Container Weight Verification system. Using Datum Electronics highly accurate and patent protected innovative bolton strain gauge sensors, Cargo Hawk seamlessly integrates to new and existing container handling equipment, without the need of introducing expensive high wearing consumable load monitoring hardware.
-
Shimadzu Corp.
After tensile testing, flexural tests are the most common strength tests for plastics and other resins. The main standards for plastic flexural (bend) tests are ISO 178, JIS K 7171, and ASTM D790, which require very accurate test systems. These standards include flexural strain measurements using a deflectometer, ranging from micro-strain measurements in the elastic region, the reversible elongation at the beginning of tests, to larger strain measurements in the plastic region. Shimadzu's deflectometers integrate easily into AG-X plus series, AGS-X series, and EZ-X test frames and Trapezium X testing software. Since these deflectometers push up against the specimen from below, the specimen color is not a limiting factor, as can be for laser type non-contact deflectometers. Furthermore, these deflectometers can partially absorb the shock during specimen failure, preventing specimen fragments from scattering.
-
SLM -
Integrated Test + Measurement
Since 2001 ITM has installed structural strain based monitoring systems in the pulp & paper and energy generation industries. For these systems, our engineers and field service technicians turn structures into measurement instruments (load cells). Load outputs from the structural load cells are monitored and published by a realtime controller to its local interface or network historians and HMIs.
