Showing results: 1561 - 1575 of 4403 items found.
-
OFSW - 2 × 1 -
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW-2 × 1 is a 2 × 1 prism optical switch. It can support 2 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
OFSW - 2 × 2 -
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW-2 × 2 is a 2 × 2 prism optical switch. It can support 2 optical fibers input and 2 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
OFSW - 4 × 1 -
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW-4×1 is a 4×1 prism optical switch. It can support 4 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
ICS Electronics
*ICS's Serial to Digital Interface boards provide the user with digital IO signals that can be user configured to match virtually any application. Both boards are available with high power relay drivers and with optional firmware designed to simplify switching applications.*All boards are designed for mounting inside a chassis.
-
Universal Switching Corporation
The VXIbus modules offered by Universal Switching Corporation are listed in the table below by "maximum" frequency range order beginning with low frequency (DC) to the highest (40GHz) followed by our soon to be released fiber optic modules. Each module has its own characteristics and features.
-
Teledyne Defense Electronics Relays & Coax Switch
For applications where no failure rate is acceptable, Teledyne Relays offers high-performance switching solutions that meet the stringent requirements of aerospace applications. EMR, Coax Switches, and MSSR product lines have been designed for use in space, and are thoroughly tested and screened at the highest levels to ensure optimal performance.
-
63-103-001 -
Pickering Interfaces Ltd.
This chassis mounting kit is designed for use with the 19-slot PXI chassis and the 18-slot LXI modular switching chassis, allowing installation into a standard 19" rack. When installed in a rack, a space of 1U should be allowed underneath the chassis for the cooling air intake, increasing the overall rack occupancy to 5U.
-
Pickering Interfaces Ltd.
Our 8-Pin D-Type connector is used on PXI and LXI switching products to provide a low density user connector solution. A 4-pin partially populated version of the 8-pin D-Type connector is also provided to match the connector pin assignment of our model 40-170 High Power Relay Module.
-
PEC N.V.
This product range offers 45V, 100V and 150V systems, with a 60A per channel capability. All systems support parallel switching for achieving higher currents. Each channel has an onboard CAN-bus connection for BMS interfacing and can be extended with auxiliary IO’s for single cell voltage and temperature measurements.
-
42-738A-001 -
Pickering Interfaces Ltd.
The 42-738A-001 is a single-slot 3U PXIe USB Hub module that combines an 8-port USB 2.0 hub and USB data/power switching to provide a controlled connection between the backplane and USB products. Each port can connect and disconnect the power and data paths separately, simulating various connection faults.
-
A500RMR-500RMR-4B050 -
Pickering Interfaces Ltd.
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
A500RMR-500RMR-5C050 -
Pickering Interfaces Ltd.
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
A500RMR-500RMR-0A200 -
Pickering Interfaces Ltd.
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).Screwlocks are provided to secure the cable assembly to a mating product.
-
A500RMR-500RMR-4B100 -
Pickering Interfaces Ltd.
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
A500RMR-500RMR-5C100 -
Pickering Interfaces Ltd.
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.