Filter Results By:
Products
Applications
Manufacturers
-
product
PCI Bit Synchronizer
LS-40-P
The Lumistar LS-40-P PCI Bit Synchronizer provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a consistent product with high reliability and long-term stability. The LS-40-P PCI Bit Synchronizer consists of the LS-40-DB Bit Synchronizer Daughterboard shown below mounted on a PCI carrier board.
-
product
Bit Synchronizers, Decoms, and DACs
Lumistar offers bit synchronizer boards compatible with the PCI bus, VME bus, and daughter-boards for use with various Lumistar products.
-
product
Integrated Receivers/Demodulators/Bit Synchronizers
Lumistar provides a wide variety of rack mount integrated receiver and diversity combiner systems. Some of these can be configured with multiple receivers, diversity combiners, and bit synchronizers depending on custom requirements. Lumistar does not manufacture any computers, but selects only the finest of the industrial machines available to provide a high performance package. Basic system setup, control, and display software is included with each of these systems at no additional cost.
-
product
Airborne Receivers & Bit Synchronizers
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
product
System Synchronizer and Distribution Board - VME
Model 6891
Model 6891 System Synchronizer and Distribution Board synchronizes multiple Pentek I/O modules within a system. It enables synchronous sampling and timing for a wide range of multichannel highspeed data acquisition, DSP and software radio applications
-
product
Bit Synchronizer Daughterboard Rates up to 25 Mbps
LS-40-DB
The Lumistar LS-40-DB Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a high performance, consistent product, with excellent reliability and long-term stability.
-
product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
product
Dual Channel Dynamic Data Simulator
LS-77-SS
The Lumistar LS-77-SS PCI Dual Dynamic Data Simulator with optional bit synchronizer allows two command simulators one bit synchronizer, and a time code reader/generator in a single short PCI board. The two Command Data Simulators and Time Code Reader/Generator are implemented in FPGA using a next generation design based on the LS-70-P. The optional bit synchronizer is achieved using the Lumistar LS-40-DB low-profiledaughterboard.
-
product
1U Quad Bit Sync for Data Rates up to 40 Mbps
LS-44-QBS
The LS-44-QBS contains up to 4 Lumistar LS-40-DB25 Bit Synchronizer Daughterboards in a 1U RackMount chassis with status lights on the front panel and all interconnections through the rear. The design contains an internal computer which runsoff DOS or Windows depending on the version selected. The DOS version boots quickly without the delays required for Windows startup. The Windows version offers networking. The unit can be connected directly to the optional 1U slideout keyboard/display, for setup resulting in only 2U of total rack height. For applications that require many bit synchronizers, a 1U keyboard/Display with KVM switch allows 32 bit synchronizers in 9U of rack height. When power is applied, the computer will operate with the last configuration unless the operator wishes to change the setup. For setup, the keyboard/display is pulled out and the display is flipped up to monitor the process. When the bit synchronizer setup is completed, the keyboard/display canbe closed up since the status can be monitored on the front panel without an external display.
-
product
Dual Channel Multi-function Decommutator
LS-55-DD
The Lumistar LS-55-DD PCI Dual Multi-function PCM Decommutator offers two multifunction decoms and two optional bit synchronizers (LS-45) in a single PCI card slot. The multi-function decoms are implemented in FPGA using a next generation design based on the LS-50-P. The simulators,decommutators, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through a low-profile daughterboard. CVSD voice, h.261 video, and IRIG Chapter 8 decoding are achieved through software.
-
product
2nd Generation PCIe Multi-function Decommutator
LS-50-E
The Lumistar LS-50-E PCIe Multi-function PCM Decommutator offers a PCM decom, PCM simulator, time code reader/generator, and optional bit synchronizer in a single short PCIe card slot. The multi-function decom and simulator is implemented in FPGA using a next generation design based on the LS-50-P. The simulator, decommutator, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through an optional low-profiledaughterboard. CVSD voice decoding, h.261 videodecoding, and IRIG Chapter 8 decoding are achievedthrough software.
-
product
2nd Generation PCI Multi-function Decommutator
LS-50-D
The Lumistar LS-50-D PCI Multi-function PCM Decommutator offers a PCM decom, PCM simulator, time code reader/generator, and optional bit synchronizer in a single short PCI card slot. The multi-function decom and simulator are implemented in FPGA using a next generation design based on the LS-50-P. The simulator, decommutator, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through an optional low-profile daughterboard. CVSD voice decoding, h.261 video decoding, and IRIG Chapter 8 decoding are achieved through software.
-
product
Industrial Automation
NAI offers a variety of resolver-based Astrosystems motion control solutions for the packaging, material handling, and automated manufacturing industries. Specifically designed for rugged defense and industrial applications, our innovative product lines include single- and multi-axis synchronizers, limit switches, encoders, position sensors, and potentiometers.
-
product
Synchronization and Distribution Amplifier - PCIe
Model 7892
The Model 7892 High-Speed Synchronizer and Distribution PCIe Board synchronizes multiple Pentek Cobalt or Onyx boards within a system. It enables synchronous sampling and timing for a wide range of multichannel high-speed data acquisition, DSP, and software radio applications
-
product
Dynamic Data Simulator
LS-70-S
The Lumistar LS-70-S PCI Dynamic Data Simulator allows complex data streams to be generated for evaluation of bit synchronizers and PCM decommutator performance. It can also be used for uplink command generation to vehicles in flight, checkout of complete telemetry links, and playback of archived hard drive data in any format with the appropriate dll. The PCI board is only 7 inches long and contains the dynamic simulator and IRIG Time Code Generator.
-
product
Automotive Conveyor Control
Convey-O-Track
Computer Conversions Corporation
Computer Conversions' Convey-o-Trak Series are standalone precision Conveyor Drive Positioners, designed specifically for assembly-line applications. They serve as a reliable means of precisely positioning conveyors in a truly closed loop system that can be either: exactly job/product rate synchronized position (Line Setters), or, absolute position synchronized to any adjacent conveyor (Synchronizers).
-
product
PCI Dual Channel Multi-Band Down Converter
LS-27-D
The Lumistar LS-27-D3 TwoChannel Quad Band PCI Down Converter product is a 3rd generation high-density, high performance down converter designed using the sameadvanced technology as in the industry leading LS-25 PCIReceiver. The down-converter converts one or two independent channels of up to four RF frequency bands down to a 70 MHz IF output. The LS-27-D3 is typically used in conjunction with theLumistar LS-35 Series Digital IF Receiver/Combiner to provide one or two independent telemetry receivers, or a dual diversity combining receiver, with up to two multi-mode demodulators and bit synchronizers in a two-slot PCI interface. The number of channels and frequency band designations can be specified at the time of order. Please see the data sheet for the LS-35-R Digital IF Receiver/Combiner for more information.
-
product
IF Digital Processing Board for Demodulation and Combining
LS-35-R
The Lumistar LS-35-R is part of the Lumistar family of digital processing boards used for programmable telemetry systems. The LS-35-R consists of a digital processing main board with two high capacity Xilinx Virtex-5 arrays. The LS-35-R provides a two-channel IF Receiver with Pre/Post detect combining, multimode demodulators with data rates up to 40 Mbps, bit synchronizer outputs, Viterbi decoding, spectral and constellation display, BER reader display and 70 MHz IF modulator with calibratednoise feature. The all-digital design assures a consistent product with high reliability and long-term stability.
-
product
Aluminum Portable Telemetry System with Integrated Keyboard and Display
LS-84-AP
The Lumistar LS-84-AP Rugged Aluminum Portable Data Unit offers a low cost, high performance COTS solution for aportable quick look ground station. Lumistar LS-25 FMReceivers or LS-25-D2 Down Converters with LS-35-R Multimode IF Receiver, Bit Synchronizers and Multi-function PCM Decommutators, and LS-71D/A Converters can be installed inthis rugged high quality portable computer and bundled with theLumistar setup, control, and monitoring software to achieve anaffordable alternative to the often expensive, proprietary architecture products of other suppliers. The flexible design allows the user to define the desired data acquisition cardconfiguration to unique requirements.
-
product
Clock Synchronization
Analog Devices Clock synchronizers are designed for wired networking applications, providing the clock redundancy functionality needed to maximize system uptime. Our technology supports clock synchronization with common standards, including 1 pulse per second (PPS) output signal from a GPS receiver. GPS signals are broadly available and utilize an extremely stable atomic clock as its time base, but they are often noisy. Systems rely on the IEEE1588 timing protocol to establish synchronous communications across the wired network, including synchronous Ethernet and synchronous digital hierarchy (SDH) to optical transport network (OTN) mapping/demapping. The IEEE1588 protocol has emerged as the preferred method for Clock synchronizing systems throughout both computer networks and local area networks (LAN).
-
product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.