Showing results: 3286 - 3300 of 4492 items found.
-
1820 ER -
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
KT-5000Pi -
Kast Eng Co. LTD.
This is a Hipot(Puncture) Tester combined with Insulation Tester in a set.It tests 2 kinds of test continuously in sequence, and any of both hipot or insulation test can be set to test first in other by the selection switch.Hipot Tester has the leakage current meter, so the operator can check the leakage value while testing. And the preset procedure of the Insulation Tester is very easy. Both tester judge the product to be good or bad automatically in a short time.This tester has many I/O ports to connect extra test system. Price : 2,550 (USD)
-
Alpha Moisture Systems
The key to the operation of Alpha Moisture Systems' Portable Analysers is the unique Desiccant Dry-Down Chamber. By keeping the sensor dry between tests, the special assembly of the head ensures that the instrument is always ready for immediate use. The head assembly consists of two chambers which have a telescopic action. When the head assembly is in the 'closed' or 'Dry-Down' position, the sensor is completely surrounded by desiccant, which absorbs the remaining water moisture from the sensor and hence it is dry and ready for use. The small space at the bottom of the test chamber enables the sample pipe to be purged before the test commences without wetting the sensor. By placing a finger over the outlet of the head, the sample pressure is able to open the test chamber automatically, exposing the sensor to the gas being tested and enabling accurate reading of moisture content in the sample gas. After each test the head assembly is closed by depressing the inner section so that the sensor will again be dried by the desiccant, leaving the sensor ready for use time and time again. The desiccant is kept in the inner chamber and is not exposed to ambient room air or the sample gas, therefore there is no need for frequent regeneration or replacement of the desiccant.
-
VectorCAST/C++ -
Vector Software Inc.
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing C/C++ software components necessary for validating safety- and mission-critical embedded systems.
-
Bestone Industrial Ltd.
This groundmeter is designed for testing ground wire of electric power net, as well as earth voltage test in the fields of household electric power system and delectric appliance application.
-
Electronic Systems of Wisconsin, Inc.
ESW Armature Test Systems are equipped with the latest features the market has to offer. The on-screen display makes it easier to read, track, and record your armature information. ESW's data collection software is compatible with almost any type of system that allows the user to store the information on any software platform. Our Testers store your data, so that you never have to worry about losing important information again. We will work with you to meet your customized testing needs. Please see the videos and slideshow below to view some of our Armature Testers.
-
Imaginant Inc.
Utilizing optical and semiconductor fabrication techniques, Imaginant manufactures the PureView PrecisionTM line of RoHS-compliant delay-line ultrasound transducers with center frequencies ranging from 50 MHz to 250 MHz (higher and lower transducer frequencies are also available). Imaginant's precision-manufacturing process produces transducers that exhibit high reliability and high uniformity from device to device. This manufacturing consistency enables uniform test system performance to be attained across multiple systems. Imaginant transducers are available in focused and flat-face models that can be produced with minimal-damping for applications requiring maximal sensitivity or with maximal-damping and high-bandwidth for applications requiring the highest-degree of temporal precision.
-
Sciencetech, Inc.
Sciencetech''s IV Testers are electrical current-voltage measurement systems used to characterize photovoltaic cell performance. This current-voltage tester works by sampling various current versus voltage combinations of the photovoltaic cell with a variable impedence load.This IV Test system can measure electrical power from photovoltaic cells up to 20W. The voltage envelope is limited to 20V and the current to 1A. A higher power version, up to 60W, is available. In general, the limitation on this model is the 1A current limit: if your solar cell generates more than 1A, we recommend upgrading to the 60W version.
-
R347B -
Keysight Technologies
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
LXinstruments GmbH
The in-vehicle test set was developed to successively measure several active RF amplifiers installed in the vehicle as well as different antenna structures. It offers the possibility to connect 12 DUTs. The DUTs can be connected to an external spectrum analyser via a 1 to 12 RF multiplexer. Each DUT can be individually switched and supplied with an adjustable voltage via a bias-tee integrated in the system. The individual bias voltages and currents are recorded by the IVTS and can be called up on an interactive control panel or via Ethernet and SCPI commands. The complete system can be powered by rechargeable battery and can be operated either via Ethernet, fibre optics or WLAN.
-
Echola Systems LLC
Echola's Optical Patch Panel Automation switch allows test engineers/system developers to dynamically reconfigure testbed connections from remote. It reduces test configuration time as they don't need to make any physical fiber connections for each set of tests, so more testing can be performed with fewer resources. It provides all-optical connectivity with zero latency and can be used with any protocols and speed. Unlike O-E-O (optical to electrical to optical conversion) switches you don't need expensive transceivers for each port. The all-optical connectivity also allows systems under test to be tested without introducing another variable (ie, another conversion layer which could introduce significant latency). The patch panel automation switch allows users to configure, control and monitor the device from remote using any standard internet browser, a command line interface (CLI) via Telnet or SSH and SNMP v2c. The event notifications are supported through Syslog. It can be automated using TCL based scripts.
-
SG-YD -
Wuhan Sangao Electrical Test Installations Limit Co.
AC and DC test oil immersed transformer.Traditional oil immersed test transformer is used to do power frequency withstand voltage and DC current withstand voltage test for variety kinds of high voltage electric device, insulating material.YD series oil transformer, also known as test booster, which test insulation strength under specified voltage for various electric products, components, insulation materials. It can test products insulation level, find insulation defect and judge overvoltage ability. It is widely used in power station, power supply and distribution system and research institute.
-
Infotainment & Telematics -
NOFFZ Computer Technik GmbH
Developing automatic test systems for the automotive industry is one of our core areas. This industry in particular is characterized by rapid technological progress and ever faster time-to-market requirements.In the vehicle, multimedia devices are used for pure entertainment, but also as vehicle information, which are intended to cover security and navigation services.Infotainment and telematics devices such as eCall modules, connected gateways, instrument clusters or the HMI (Human Machine Interface) are networked with each other and with the most important vehicle functions. All of this is made possible - in addition to GNSS (Global Navigation Satellite System) - by wireless and new communication standards such as A 2 B, BLE, C-V2X, Wi-Fi 6 and 5G.The complex networking is a very attractive factor for drivers and passengers, but this complex communication can become a major challenge for developers.High-speed interfaces and high-frequency modules used in combination must send and receive signals between the different devices absolutely error-free.With our individual and sensitive test and inspection systems, we also simulate vehicle components or emulate the vehicle environment and thus ensure the functionality of your devices. We take your pioneering developments to the next level.
-
SCR ELEKTRONIKS
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
MicroContact AG
The AOI handling system is a compact facility with various test units. Via an ionization cleaning station the ceramics are transferred to the contacting station. There, the resistance values of the substrates are tested with a rigid needle adapter. Afterward, the ceramics are further conveyed to the three (optionally four) AOI test stations (for automatic optical inspection) and are tested for cracks, unevenness, faulty imprints, contamination, etc. The poorly evaluated ceramics arrive at a review station where the operator can assess and evaluate the errors on the monitor. If the operator is uncertain about a fault, the ceramic in question can be positioned under the microscope position and inspected by eye. Poorly defined ceramics are marked accordingly with an ink pen.