Filter Results By:
Products
Applications
Manufacturers
T1
A phone line connection with data rates of 1.544Mbits per second over 24 channels running at 64Kbs.
See Also: E1
-
product
T1 E1 Testing
T1/E1 carriers are used extensively throughout the world for carrying large volumes of call containing both voice and data. Their popularity can be attributed to their high reliability, manageability and flexibility. The available digitized channels, 24 for T1 and 32 for E1 can be used for carrying voice and/or data. Further, the carriers can be used separately or they can be combined in order to provide higher transmission bandwidth.
-
product
E1 T1 Tester
NetProbe 2000 PDH
New Generation Analyzer for Legacy PDH networksThe NetProbe 2000 E1E3 is newest, state-of-the-art handheld analyzer on the market for testing the legacy E1 and E3 in PDH networks. It includes all features for E1 & E3 BERT and E1 physical layer testing. Automated line monitoring performs autocheck of essential alarms and errors.
-
product
Infrared T1 3/4 LED
350-00003
T1 3/4 Infrared light emitting diode, for breadboard or through-hole projects. Used with the LED Standoff and LED Light Shield to build the IR Transmitter Assembly (#350-00017). Frequently used with the IR Receiver for object detection and autonomous robot navigation, this is a compatible replacement wherever an Infrared LED is found in any of our Education Kits Components Listings.
-
product
850NM T1 3/4 Phototransistor
350-00029
This phototransistor responds to visible light as well as the lower infrared range.
-
product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
product
Direct Access To T1 E1 DS0 On OC-3/12 STM-1/4 On LightSpeed1000™
Voice, data, and video traffic is exploding as smartphones, IP TV, video streaming, and "cloud" based services takeoff. A majority of the backbone transport for these applications continues to be SONET and SDH optical transmission networks. A dominant protocol for IP transport is PoS (Packet over SONET) and another is ATM (Asynchronous Transfer Mode). Both schemes are packet based, with ATM using fixed size packets of 53 bytes called "cells", and PoS using variable packet sizes closely matching to Ethernet frames.
-
product
Low Voltage Test System
CKT T1
The CKT T1 is a compact size solid-state test system featuring 128 test points.
-
product
WAN Tester
The Telinc WAN Tester is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, modems, multiplexers, CSU/DSUs, T-1 ESF CSUs, DU, NTUs and TIUs.
-
product
Analog Platforms
(T1/E1/T3/E3/OC-3/OC-12/STM-1/STM-4)
Almost all T1 E1 T3 E3 Testers can be accommodated into rack-based units. Multiple rack units can be stacked together for greater scalability. Shown below is a rack based tProbe™ T1 E1 / T3 E3 Analyzer unit, and a Channelized T3 E3 Analyzer unit supporting 6 T3s (6 * 672 DS0s). Such customized rack serves the purpose of handling multiple communications lines and test complex functionalities.
-
product
WAN Tester lllD
It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems, multiplexers, CSU/DSUs, T-1 CSUs, DDS CSUs, DDS CSU/DSUs, DTUs, NTUs and TIUs. The Ds3 tester is supplied with user-changeable nickel metal hydride batteries and a built-in charger.
-
product
WAN Tester III
The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.
-
product
WAN Tester II
The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It is supplied with changeable nickel metal hydride batteries and a built-in charger.
-
product
Lamp gauge
E27
Shenzhen Chuangxin Instruments Co., Ltd.
To check the maximum dimensions of the screw thread and dimension T1 minimum of caps on finished lamps shown on sheet 7004-2.
-
product
ISDN Chip Set
Emutel Symphony
Emutel Symphony is a convenient and flexible Basic Rate ISDN, Primary Rate ISDN and Analog PSTN network simulator. With support for S, U, E1, T1 and PSTN analog interfaces you can use the Emutel Symphony to test and develop a full range of ISDN(E1/T BRIS BRIU) and PSTN analog (FXS) equipment.
-
product
WAN Simulator / Emulator
LANforge ICE
LANforge ICE emulates networks that involve limited bandwidth, latency, packet loss, and corruption. LANforge ICE tests the behaviour of devices that sit on either side of an impaired network. Reduces lab and training costs by replacing expensive WAN hardware, such as T1 and FrameRelay devices. Automates testing with various scripting features and libraries.
-
product
New Generation Analyzer For IEEE C37.94
NetProbe 2000 C37.94
The NetProbe 2000 C37.94 is a field analyzer with IEEE C.37-94 Multimode optical fiber interface for testing bit error preformance between teleprotection and digitalMultiplexer equipment. Can be combined with many optional interfaces for T1,E1, WiFi, VoIP and V-series testing.
-
product
PXI/PXIe Trigger Module
PXT1741
The PXT(e)1741 Trigger Module ist designed to build up a connection between trigger signals from any external trigger source (5V TTL Standard) and the PXI(e) trigger bus. Therefore the device is equipped with four SMA front connectors (T1 to T4).
-
product
2 Port T1/E1/PRI ISDN Simulator PCI
SIM-2PRI-PCI
The most inexpensive ISDN PRI simulator on the market. Designed in standard PCI card form factor it has two PRI(T1 or E1) ports allowing ISDN PRI equipment to be connected together just as if they were connected through the ISDN network. Simulator card does not require any OS drivers, completely software independent and it take only power from the host computer.
-
product
100BASE-T1 Automotive Ethernet Protocol Analyzer
100BASE-T1
Prodigy Technovations Pvt. Ltd.
100BASE-T1 Automotive Ethernet Protocol Analyzer is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. Automotive Ethernet interface scales up to address current and future needs of in-vehicle bus speed requirement. Need for higher-speed in-vehicle bus is increasing to support feature-rich ADAS and connected vehicle needs. Two-wire full duplex 100BASE-T1 PAM 3 signaling is the choice of interface bus to address these needs
-
product
Lamp Cap Temperature Rise Test System
CX-T1
Shenzhen Chuangxin Instruments Co., Ltd.
Lamp Cap Temperature Rise Test System is according to IEC60360-1998 and GB2512-2001(Standard method of measurement of lampcap temperature rise). It is used to test the working and environmental temperature as well as temperature-rise of the burner and lamp. It meets the requirement of IEC and GB Standards
-
product
LED Type Wafer Alignment Sensor Controller
HD-T1
Panasonic Industrial Devices Sales Company of America
The HD-T1 Series is a new Wafer Alignment Sensor that uses a safe red LED light beam, with a resolution of 30µm, to achieve the same high level performance as Laser Sensors. The HD-T1 Sensor is best suited to detect wafer eccentricity, notches and orientation flats. Using linear image Sensor methodology and high-speed sampling technology, a wide variety of objects can now be stably measured with great precision at ultra-high speeds. This CCD style Sensor is developed for use in almost all fields of industry, e.g. tire manufacturing or Semiconductor production (Wafer Printed Circuit Boards).
-
product
Ultra-compact Laser Collimated Beam Sensor
HL-T1
Panasonic Industrial Devices Sales Company of America
The HL-T1 Sensor is an ultra-small laser Thru-Beam Sensor with very high resolution.
-
product
BT Imagine New wafer Thickness System
IS-T1
Measurement Technique Laser Triangulation1-3 Laser Sensor SpotsLaser Spot Size Optimized for Accuracy and Precision.
-
product
Current Transformer Tester
CT-T1
The CT-T1 is a microprocessor-based Current Transformer Tester that measures CT excitation current, turns ratio, and winding polarity tests, all without having to switch the leads during testing. The instrument has a fully automatic knee point detection (ASA 10/50, IEEE 30°, IEEE 45°). Although includes 5 low side taps and 1 high side tap.
-
product
GPS Clocks
TesCom's line of GPS Clocks includes three models - the TiemPo 6400A, the TiemPo 6400N Nano, and the Ts2 Multi-Sync Packet Gateway. Whether you need synchronization solutions for TDM (T1, E1, CC, frequency) or Packet (PTP/SyncE, 1PPS/10MHz, ToD) in your central office or rugged field cabinet, we have time and synchronization solutions for your needs.
-
product
Digital And Analog Call Simulation
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
product
Non-Destructive Subsurface Layer Profiling
NMR-Mouse one-sided NMR
The unique, powerful Profile NMR-MOUSE® probe works hand-in-hand with the Kea2 spectrometer. The Profile NMR-MOUSE is a portable, open NMR sensor equipped with a novel permanent magnet geometry that generates a flat sensitive volume parallel to the scanner surface. The system can measure *Proton density as a function of depth *T2 NMR relaxation times *T1 NMR relaxation times *Self-Diffusion coefficient of liquids
-
product
On-line TOC Analyzer
T1 - TOCADERO Series
- Highest analytical precision with short measuring time- Catalyst-free high-temperature process at 1200°C with "Fast Change Technology- Most modern hardware components andindustry 4.0 features- Minimal material requirements and support costs- Highest processing quality- "Made in Germany"- Global service and support- Convincing cost of ownership
-
product
T3/E3, OC3/OC12, & STM1/STM4 Testing
T3 E3 Analysis software compliments the hardware and supports simultaneously monitoring up to 12 x T3 E3 lines (2x Rack units) for all alarms, frame errors, signalling and data. If one adds the Channelized T1 Analyzer software to the system, then the T1s within the T3s can also be analysed in software, 12 x T3 E3 lines (=12*28 T1s) constituting 336 full duplex T1s, or 672 simplex T1s monitored simultaneously using a single Rack unit.
-
product
Dual Temperature
The Fieldpiece Dual-Temperature Accessory, model ATH4, measures two temperatures simultaneously using the included k-type, wrap tab beaded thermocouples. The technology inside the ATH4 provides superior temperature compensation in rapidly changing environments commonly found while performing field service. Use the ATH4 to find Delta T and just about any temperature split you want to measure. Displays T1, T2 and T1-T2 on your Fieldpiece meter, handle or data logger. It is included with the HVAC Guide® System Analyzer to get target superheat and for the Target Evaporator Exit Temperature test. Fieldpiece offers a wide variety of k-type thermocouples for various HVAC specific applications. Use pipe clamp T/Cs with the ATH4 to check for blocked filters.
