Showing results: 1 - 15 of 42 items found.
-
TESTEX Testing Equipment Systems Ltd.
Elmendorf Tear tester, a computer controlled falling-pendulum instrument, to decide the ballistic tearing strength of textiles, plastics, paper or board. Tear Strength Tester complies with ASTM D1424/5734, ISO 1974/9290, BS ISO 13937, etc. The tearing tester is further enhanced and supported by the easy to use computer. Elmendorf Tear Strength Tester will show its good performance when you do Elmendorf tear test.
-
DWTT -
Qualitest International Inc.
Since the introduction of the Drop Weight Tear Tester - DWTT, materials have moved on. In particular, demands for high operating pressures of line-pipes and larger diameters have driven the development of higher strength steels. Forty years ago the work that led to the drop weight tear test was done on X52 steel (360MPa yield strength). Improvements in thermo-mechanical processing has yielded improvements of approximately 10,000psi per decade, to the point where the state of the art is now X100 steels, and the use of X120 steels is being considered.
-
TF140C -
TESTEX Testing Equipment Systems Ltd.
It enables rapid determination of the dynamic resistance of materials designed to be subjected to strong shearing loads (e.g. fabrics) or liable to be damaged by sharp or heavy objects (e.g. paper bags). Subsequently, the test was naturally adopted for all materials in the form of sheet or films, cardboards, cloth, knitted fabrics, plastic films, aluminium foil, non-woven fabrics, complex flexible packaging etc.
-
FPT-H1 -
Mecmesin Limited
The FPT-H1 is a dedicated horizontal tester, designed for testing to all the key industry and international standards for coefficient of friction, and for appropriate horizontal peel and tear methods. Its sleek contemporary styling incorporates ease of use and maintenance. Built to exacting standards, yet affordable, the FPT-H1 provides the most accurate and detailed measurement, with guaranteed repeatability in testing. It is ideally suited for the packaging industry, for manufacturers, converters and users of paper, board and plastic films, plus coatings, floor coverings and textiles.
-
Qualitest International Inc.
The Scott Internal Bond Impact Tester is used to determine tear resistance (Elmendorf). A sample is torn with the help of the pendulum device starting from a predetermined cut. The work required for a tear of a given length is measured.
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Tensile Testing Machine is widely applied to test the tensile, tear, peel, and bend of all kinds of materials, such as metal, cable and etc, it’s used to test the tensile, tear, peel, compressive strength and bending of the material. It conforms to the standard of GB, ISO7500/1, JJG475-88, ASTME4, DIN5122, JISB7721/B7733, EN1002-2, BS1610, and CNS9471/9470.
-
CX-106 -
Shenzhen Chuangxin Instruments Co., Ltd.
The Tensile Testing Machine is widely applied to test the tensile, tear, peel, and bend of all kinds of materials, such as metal, cable and etc, it’s used to test the tensile, tear, peel, compressive strength and bending of the material. It conforms to the standard of GB, ISO7500/1, JJG475-88, ASTME4, DIN5122, JISB7721/B7733, EN1002-2, BS1610, and CNS9471/9470.
-
-
eSBC -
Patton Electronics Co.
Session Initiation Protocol (SIP) is the communication technology employed to set up and tear down VoIP phone calls
-
Elcometer Limited
Hardness can be defined as a material’s resistance to permanent deformation. In the coatings industry, hardness measurement can be used to determine the resistance of the coating to scratching from general wear and tear and also if a coating is fully cured.
-
Guangzhou Biaoji Packaging Equipment Co., Ltd.
Packaging Material testing including OTR barrier, COF, lamination bond strength, material analysis, physical properties, tear strength , tensile strength, puncture, slip, blocking, scuffing, film thickness variation, WVTR and so on..
-
ROM-Elektronik GmbH
A fault (also rupture, crack, displacement or disturbance in the narrower sense) is a tectonic tear or fracture in the rock, which offsets two rock areas or crust parts over distances from the centimeter range to a few tens to hundreds of kilometers.
-
CX-108 -
Shenzhen Chuangxin Instruments Co., Ltd.
The Tensile Testing Machine is widely applied in all kinds of materials, such as metal, cable and etc, it’s used to test the tensile, tear, peel, compressive strength and bending of the material. It conforms to the standard of GB, ISO7500/1, JJG475-88, ASTME4, DIN5122, JISB7721/B7733, EN1002-2, BS1610, and CNS9471/9470.
-
#21025C -
NSI Industries
Extend the life of your tester by using the RJ45 PortSaver as your sacrificial cable. Eliminates the wear and tear from constantly plugging in and out of the tester port and minimizes the risk of damaging the RJ45 jack if the connector contacts are not crimped completely. Compatible with all Platinum Tool testers with built-in […]
-
Guangzhou Biaoji Packaging Equipment Co., Ltd.
Flexible Packaging Testing Service mainly included OTR barrier test service,WVTR Testing Service, COF Coefficient of Friction test, lamination bond strength, material analysis, physical properties, tear strength , tensile strength, puncture, slip, blocking, scuffing, film thickness variation etc.