Showing results: 1801 - 1815 of 5231 items found.
-
215 -
Elcometer Limited
Memory stores up to 260,000 readingsIdeal for testing for powder or liquid coatings in batch or conveyor ovensVariable measurement interval, date, time, °C / °FHigh temperature resistant teflon coated probe cables are easy to clean after each runQuick display shows maximum temperature, Cure-Index figure and pass/fail for each probeMeasure up to 6 different temperatures at one timeIdeal in situations where powder coated thickness is inconsistentStart and stop logging at a pre-set temperatureLarge menu-driven display for easy operationPrint full colour report directly to any HP printerUSB data output to ElcoMaster® software and combine with other key inspection measurements
-
MCP9600 (Screw Terminals) -
SparkFun Electronics
The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 can read both the ambient temperature and the temperature of whatever you're trying to measure! The MCP9600 can do both with a resolution of 0.0625°C, and an accuracy of ±1.5°C (worst-case). The MCP9600 Thermocouple Amplifier is one of our many Qwiic compatible boards! Simply plug and go. No soldering, no figuring out which is SDA or SCL, and no voltage regulation or translation required!
-
Extech MO220 -
Extech Instruments Corporation
The MO220 is specifically designed for monitoring moisture in wood. Memory contains 8 wood groups with calibrations for approx. 170 species of wood. Measurements can be taken using the integral pin electrodes or the included heavy duty remote probe. Automatically temperature compensated (ATC) readings when used with the temperature probe. Built-in calibration check, replaceable measurement electrode pins, user settable Auto Power off (1 to 9 minutes) with disable, and Low battery indication. Complete with protective cap, temperature probe, heavy duty remote moisture probe, replacement pins, two AAA batteries, and soft case.
-
ICT-4 -
Physitemp Instruments
ICT-4 Micro-Surface Microprobe - For use on integrated circuits and other micro specimens. 0.013'' diameter .5'' straight stainless steel shaft; slightly protruding sensor bead to facilitate temperature probing. 5'' tubular handle fits micro-manipulators. Maximum intermittent temperature 200°C, continuouse use 100°C, Time constant 0.025 Seconds. 5 foot lead. Not isolated.
-
PCE Instruments
The pyrometer is ideal for taking accurate measurements of temperature without contact. Thanks to an optical mechanism, the pyrometer is safe for measuring high temperatures. Its infrared capabilities make the pyrometer the perfect tool to use when a conventional sensor is inadequate. A pyrometer is useful for measuring moving, extremely hot or hard-to-reach objects. Many pyrometer models can be calibrated to meet ISO standards.
-
MX-9200 -
LR Environmental Equipment Co. Inc.
A high reliability thermostatic temperature controller maintains the salt solution at a preset controlled temperature in a reservoir within the double wall construction. The salt solution is introduced into the chamber through an atomizing nozzle. The nozzle can be calibrated by us to perform to MIL-STD-19500B, paragraph 40.8 and other specifications. This specification requires that a salt residue be deposited on the specimens, in addition to generating salt fog atmosphere.
-
TH-5/AOP -
Physitemp Instruments
The TH-5?AOP is one of our most economical precision thermometers in the Physitemp product line. The TH-5/AOP offers the same high accuracy (0.1°C ±1 digit) and resolution as all our other thermometers, but with a narrow temperature range. The TH-5 is ideally suited for either a laboratory or hospital setting where continuous temperature readings within the physiological range are sufficient.
-
TS-4SMP -
Physitemp Instruments
With our TS-4SMP Thermal Stage for Petri Dish, a specimen on a microscope slide or culture dish can be maintained at any temperature between -20°C and +60°C. Setup is easy, takes little time, and the controller will regulate the stage temperature to within +/-0.1°C. The collar on the stage is designed to accommodate a 35mm 'Nunc' petri dish. The collar may also be removed for use with slides.
-
T7511-4 -
COMET SYSTEM, s.r.o.
Web Sensor with relative humidity and temperature probe on the cable. Built-in atmospheric pressure sensor.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
T7511 -
COMET SYSTEM, s.r.o.
Web Sensor with relative humidity and temperature probe on the cable. Built-in atmospheric pressure sensor.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
T7510 -
COMET SYSTEM, s.r.o.
Web Sensor with built-in temperature, relative humidity and atmospheric pressure sensors. High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
T7511-2 -
COMET SYSTEM, s.r.o.
Web Sensor with relative humidity and temperature probe on the cable. Built-in atmospheric pressure sensor.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
IR-300 Series -
HORIBA, Ltd.
Metal-Organic Chemical Vapor Deposition (MOCVD) is widely used in the manufacture of LEDs, optical devices and other components. Liquid and solid precursors are delivered to the reaction chamber by controlling the temperature, pressure and the carrier gas flow rate (bubbling method). Process results can be affected by changes especially in temperature and liquid level. The in-line IR-300 Series measures and reports the precursor concentration in real time.
-
EverythingPCB
AkroMetrix provides a variety of products to help you identify and evaluate warpage: For warpage measurements along a production line or at room temperature, AkroMetrix has developed the LineMoiré Production Level Automated Flatness Inspection System. If you need to measure warpage and flatness during pre-defined temperature profiles, AkroMetrix's TherMoiré In-Process Warpage Measurement Systems may fit your requirements.
-
CIP-1000 -
Advanced Thermal Solutions, Inc.
The CIP-1000, Controllable Isothermal Plate, is a system for providing an isothermal surface that can be precisely temperature-controlled from 10 to 170C with an accuracy of +/- 0.1C. The CIP-1000 features a 75 mm diameter isothermal copper plate whose constant temperature can be raised or lowered both automatically and manually. A three wire RTD sensor and integral PID controller ensure specific, uniform temperature across the entire plate.
