Filter Results By:
Products
Applications
Manufacturers
Temperature
a measurement of heat or cold.
-
product
Walk-In/Drive-In Humidity Environmental Chamber
Burnsco Environmental Test Chambers
These custom designed chambers are used for testing large products, vehicles, or batch testing. They offer temperature and humidity simulation capabilities for climatic testing and temperature/humidity cycling whenever there is a need to simulate wide temperature and humidity extremes. They can be made almost any length, width or height.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Ion 700 Benchtop Meters
Oakton benchtop 700-series meters are designed for use in crowded laboratory settings. Compact footprint of less that 6" x 7" (16 x 18 cm) conserves valuable space, while the large, dual-display LCD provides excellent visibility—even from a distance. Ion 700 meter measures pH, mV, relative mV, ion concentration and temperature. Automatic temperature compensation (ATC) maintains reading accuracy even with fluctuating temperatures. Models feature five-point pH calibration with automatic buffer recognition for both USA (pH 1.68, 4.01, 7.00, 10.01, 12.45) and NIST (pH 1.68, 4.01, 6.86, 9.18, 12.45) pH buffers. Meters additionally feature ion concentration calibration of up to 5 points. Meter features include Auto-Hold, selectable °F or °C measurement, and easy recall of electrode slope or offset. The convenient pull-out quick reference card keeps procedures handy at all times. Use 700-series meters with any pH, ORP, or ISE electrodes with a BNC connector.
-
product
High-Mount Outdoor Infrared Motion Sensor
ENVIROMUX-IMD-OHM
High-mount outdoor weatherproof sensor with 94 detection zones. Unique pyro-element provides multiple pattern detection and accurate discrimination function for spot temperature changes of moving objects. Drastically reduces false and missed alarms caused by severe outdoor environmental changes. Upper and lower area must be activated to generate an alarm condition. Summer night compensation, advanced temperature compensation, and vegetation sway analysis logic. Ideal detection area setting – adjustable length/spot detection. Registers movement in area covered: 13/18/30/40 ft and 85° wide. LED indicators for operation and system status. Unwanted detection areas can be eliminated using the included area masking seal. Mounting height: 8.3 to 10 feet. Tamper switch opens when cover is removed. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: -4 to 140°F (-20 to 60°C). IP54 compliant. Powered by ENVIROMUX-2D/5D/16D.
-
product
Indoor Compact CO Monitor with Tilt Leg Stand
Extech CO30
Extech Instruments Corporation
The CO30 is a CO Monitor which displays Carbon Monoxide (CO) concentration, Air Temperature, and Relative Humidity. The CO30 features a programmable audible alarm with a high decibel beeper, sounds when CO concentration rises to unsafe levels. Unit can be wall mounted or used on a desktop close to areas of concern. Other features include a visible bright tri-colored (green, yellow, red) LED alarm indicator, a "ZERO" re-calibration function, manual temperature and relative humidity compensation (adjustable), CO calibration function in fresh air, and a low battery indicator. Complete with universal AC adaptor (including US, EU, UK, and AU plugs), and 4 AAA batteries.
-
product
Wide Range Mini IR Thermometer
Extech 42510A
Extech Instruments Corporation
The 42510A Compact thermometer measures temperature from -58 to 1200°F (-50 to 650°C) with 0.1 degree resolution for readings up to 999.9 degrees. Adjustable High/Low set points with audible alarm alerts user when temperature exceeds the programmed set points. Adjustable emissivity for better accuracy on a variety of surfaces. Built-in laser pointer identifies target area. Backlighting illuminates display for taking measurements at night or in areas with low background light levels. 12:1 distance to target ratio. Data Hold and Min/Max, Over range indicator and Auto power off functions. Complete with 9V battery and pouch case.
-
product
RH Calibrator / Dew Point Generator
Edgetech Instruments'' portable calibration system offers the highest accuracy available for both relative humidity and temperature. Using chill mirror technology and precision PRT's, Edgetech''s calibrators offer best repeatability, stability and reliability when measuring RH and temperature. The calibrators are used mainly by calibration labs as a reference standard.The Edgetech Instruments dew point generator, DewGen, another calibration lab favorite, can be used as a stand alone or with a NIST traceable chill mirror dew point system creating very accurate dew points or frost points. Depending on the dry gas source this generator can create dew points from +15C to -80C.
-
product
Humidity Data Loggers
Rotronic Measurement Solutions
The long term recording of humidity and temperature conditions is very important in the pharmaceutical industry, production processes, storage, test facilities and many other areas. Once logged, the temperature and humidity data can be evaluated statistically. This provides valuable information on conditions that can have an influence on people and product quality. ROTRONIC data loggers fulfill the FDA requirements of 21 CFR Part 11 and GAMP 5. They are extremely accurate and easy to use. The data can be accessed wirelessly, via a network, or directly with the HW4 software. The data can be saved in tamper-proof LOG mode or in Excel files. For added security, the measured data from the data logger is monitored and stored redundantly online on a server or PC.
-
product
Data Logger
CTL2000
MadgeTech's Carcass Temperature Data Logger measures and records data from up to 8 thermocouple channels allowing the user to verify and validate post-production meat pasteurization cycles. The CTL2000 aids in reducing pathogens, and helps to ensure post-slaughter pasteurization process parameters are met.
-
product
Data Logger for Weather Station, 4G
HD33MT.4
HD33MT.4 with 4G/3G/2G/GPRS modem. Optional Ethernet. Designed for solar power. Integrated charger. Data Logger for weather station - remotely monitoring temperature, humidity, atmospheric pressure, solar radiation, rainfall quantity, wind speed and direction. Calculating sunshine duration.
-
product
Digital Thermometer
PeakTech Prüf- und Messtechnik GmbH
This handy single-channel temperature measuring device for type K thermocouples with a large illuminated LCD display and various measuring functions such as maximum value and data Hold can be used universally in areas such as education, refrigeration and air conditioning, food production / storage, agriculture, chemistry and industry.
-
product
Gas Analysis
T34 Compensated
A three-channel compensated (6 element) thin-film thermopile in a TO-8 package. Each active area is 3.16mm x 0.4mm. Offers thermal compensation to minimize effect of sudden ambient temperature change. Internal aperture minimizes channel-to-channel crosstalk while increasing sensitivity.
-
product
High Power Resistance Decade Box
HPRS Series
The HPRS Series resistance decade boxes employ state-of-the-art precision resistors of various types for high accuracy, high stability, and low temperature and power coefficients of- resistance. High-power resistors within the unit are made available without sacrificing other electrical properties.
-
product
Infrared Calibration
Optical pyrometers can be calibrated from 800 to 2300C using NIST certified ribbon filament lamps and temperatures up to 3500C using a graphite arc furnace. Infrared thermometers can be calibrated from -30C to 2300C utilizing state-of-the-art blackbody sources and transfer standards.
-
product
In Line Load Cell (10KN-50KN)
106, 107, 108 Series
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 50kN and 10klb with better than ±0.5% non-linearity. This type is also available with fully welded cover.
-
product
Mini PDF Logger
Compact, single-use temperature loggerOne model for any trip durationBuilt-in USB connector, no special reading device neededNo software required to download dataOn-board software automatically creates PDF reportView reports on a PC or tabletRecorded data automatically scaled to fit full graph
-
product
Radiometric Detectors
Radiometric detectors are built by using selected, stability tested high-grade Si-photovoltaic cells. They are all equipped with individually produced and matched color glass filters. They are available in different sizes for irradiance and radiant flux measurement, both in temperature stabilized laboratory and general purpose form.
-
product
Chemical Vaper Deposition R&D System
MODEL CVD-300-M
High Temperature, 1080 C (24" Hot Zone: 126 Cubic In.) High Purity Quartz Tube with Water Cooled End Caps. Broad Pressure Range of Atmosphere to 10-3 Torr. Upgradable to High Vacuum. Computer Interfaceable. Small Footprint (26" x 48"), Portable with caster mounts.
-
product
Pulse Heat Unit (Hot Bar Bonder)
*This method is most suitable for reliable soldering and thermo-compression because heating and cooling are done applying the pressure force*Good repeatability of heating temperature and time requires no skilled workers*Partial heating in short time allows to reduce thermal damages*For implement of Pb free
-
product
Arasan PHY IP
Arasan PHY’s are readily available and in production with multiple foundries from 16nm to 180nm. Our PHY’s are designed for low power on the most advanced nodes for the mobile market while also targeting the automobile market on specialized nodes where extreme temperature tolerance is required.
-
product
Mini pH Electrode (10x120mm)
Extech 60120B
Extech Instruments Corporation
The Extech 60120B is a pH Electrode. This electrode fits virtually any pH meter that accepts a BNC connector. Features a 0°C to 80°C operating temperature, 0 pH to 14 pH range, and a glass pH sensing bulb surrounded by protective teeth.
-
product
High-Precision Thermometer
The high-precision thermometers from Anton Paar are designed for the most accurate temperature measurements, comparison calibrations and fixed point calibrations in industry, laboratories and research. Combined with calibrated platinum resistance thermometers, Anton Paar's thermometers achieve a measuring uncertainty of 10 mK or less.
-
product
Portable Fluid Conditioners
PCL-III
Bemco PCL-III portable fluid conditioners are furnished as free standing caster mounted systems, ready to provide a reliable and precisely controlled flow of temperature conditioned fluid. To save floor space, these systems are also packaged with larger space simulators and thermal vacuum systems.
-
product
High Current Probe/DMM
655
Another great tool for all around electrical troubleshooting. The #655 is ideal for all high current applications, especially starting and charging diagnostics. The #655 can measure up to 1000 Amps AC or DC. Unit features built-in degrees F and C temperature readings.
-
product
DC Block, 50 kHz to 50 GHz
N9398F
The Keysight N9398F DC block offers a new level of DC blocking with performance specified from 50 kHz to 50 GHz. This DC block features a broad frequency range, excellent return loss, very low insertion loss and excellent temperature stability.
-
product
DC Block, 700 kHz to 67 GHz
N9398G
The Keysight N9398G DC block offers a new level of DC blocking with performance specified from 700 kHz to 67 GHz. This DC block features a broad frequency range, excellent return loss, very low insertion loss and excellent temperature stability.
-
product
DC Block, 50 kHz to 26.5 GHz
N9398C
The Keysight N9398C DC block offers a new level of DC blocking with performance specified from 50 kHz to 26.5 GHz. This DC block features a broad frequency range, excellent return loss, very low insertion loss and excellent temperature stability.