Showing results: 121 - 135 of 440 items found.
-
HILT Kit -
ATSI
The HILT-Kit is easy to use, with quick and accurate tools designed to test and measure the parameters of inductive loops used in the Traffic Signal, Vehicle Data Collection, and Parking industries. The test kit is housed in an impact resistant case with a set of 6 foot test leads and adapters. The sturdy, injection molded plastic carrying case is custom designed to hold the HILT-9000 and its accessories, as well as the LF-22 Loop Finder and AEMC 6527 Digital Megohmmeter for a complete loop analysis kit. (The HILT can be ordered by itself, without the Loop Finder and Megohmeter as the HILT-9000)
-
VS-10a -
Allied Edison LLC
The VS-10a power supply is a light weight, portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 10 amps, thus the name VS-10a. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-10a is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case.
-
6210A IN (Ranges: 0.5kV, 1kV, 2.5kV, 5kV) -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Four insulation test voltages.● Insulation resistance; auto ranging on all ranges.● Bargraph indicates test voltage; rise and decay can be observed during tests.● Visual and audible warning if external voltage is present.● Fully protected: crow bar.● Carry case.● EEPROM calibration.
-
6211A IN (Ranges: 1kV, 2.5kV, 5kV, 10kV) -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Four insulation test voltages.● Insulation resistance; auto ranging on all ranges.● Bargraph indicates test voltage; rise and decay can be observed during tests.● Visual and audible warning if external voltage is present.● Fully protected: crow bar.● Carry case.● EEPROM calibration.
-
Titan -
The Eclipse Foundation
Titan is a TTCN-3 compilation and execution environment with an Eclipse-based IDE. The user of the tool can develop test cases, test execution logic and build the executable test suite for several platforms. TTCN-3 is a modular language specifically designed for testing (the acronym itself stands for Test and Test Conformance Notation), standardized by ETSI (see www.ttcn-3.org) and endorsed by ITU.
-
Spectro 2 -
COMPRION GmbH
# SO/SWP terminal simulator for Smart Card testing# Test Cases for ISO, SWP and HCI# ISO/SWP/HCI/USB trace function for ensuring interoperability between a real Smart Card and a handset
-
TACK10 -
UEi Test & Measurement Instruments
Convenient Test and Check Kit, for quick testing, includes True RMS Clamp meter, Combustible leak detector, Dual input manometer, NSF waterproof thermommeter, Carrying case
-
CBA 3000 -
Altanova Group
CBA 3000 allows any timing test, motion and speed analysis, multiple contemporary static and dynamic contact resistance measurements, both sides grounded (BSG) tests, undervoltage condition test and more. All these functions are integrated in a single lightweight test case without the need of connecting additional external modules.
-
UWE Electronics
multi-site sockets include anything from strip test sockets to test sockets for wafer test to multi-position, singulated devices. The advantages of these sockets can be enormous as test time can be decreased by a factor of ten over conventional one up testing. In most cases, the throughput is only limited by tester capabilities and/or handling capacity.
-
106 -
Elcometer Limited
Applications for the Elcometer 106 Adhesion Test include paint or plasma spray on bridge decking, coatings on steel, aluminium, concrete etc.Supplied in a carry case - ideal for site testsHand operated - no need for a power supplyIncludes a cutter for EN13144 and ISO 4624 tests
-
AE6910R -
Keysight Technologies
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
-
GMDSS Tester MRTS-7 -
Aeromarine SRT Ltd
The International Marine Organization (IMO) orders all GMDSS equipment to pass regular maintenance and to confirm that it meets all the appropriate performance requirements. In case of test failure ships can be detained in Port.
-
QA Mentor, Inc.
With manual testing services, we will hand-pick a team dedicated solely to your project. Our professionals will work with your developers, business analysts, and managers to go over requirements, build a comprehensive test plan, design thorough test cases, rapidly execute the tests, help remediate defects, and retest until the project is satisfactorily completed. The same individuals will be with you from beginning to end, so they have a complete understanding of the project and how you want it done, and you will always know exactly who you are dealing with. The same QA Engineers that develop the test cases will also execute them, leaving no room for misunderstandings and greatly expediting the process.
-
GA-50 -
The Eastern Specialty Company
The TESCO Field Test Kit with Resistive Load has been designed to reduce the weight of field test equipment to the lowest possible limit. The carrying case is fabricated from durable powder coated aluminum. The total weight of the Field Test Kit including leads and digital standard is approximately 25 lbs.
-
A.T.i. Software GmbH
In the simplest case, the BST can be carried out via the connector of a module.Digital components require a JTAG port. In direct comparison to the ICT, the BST requires longer test times and the testing of analog components is not possible.