Showing results: 211 - 225 of 333 items found.
-
NTA00002B -
Keysight Technologies
Nemo Outdoor is a laptop-based drive test tool for wireless network testing which supports over 300 terminals and scanning receivers from various vendors, all latest network technologies and latest smartphones. Nemo Outdoor offers a full drive test solution for wireless network testing / mobile network testing, troubleshooting, and optimization.
-
Cohu, Inc.
For optical sensor test Cohu offers a variety of solutions being driven by requirements for tri-temp, parallelism and stimulus spacing. Customized optical stimulus units are integrated into Cohu’s test handling systems. For light detector test, we implement different types of light sources, such as infrared, ambient- and colored light. We offer different solutions for 3D image sensors combining emitter and receiver tests of LiDAR, Time of Flight and Structured Light devices.
-
Virginia Panel Corporation
The G12x Receiver has four removable rubber feet below the platform and also allows for permanent tabletop mounting. Available with 15" or 20" platforms. The G12x accepts ITAs designed for both the G12 and G12x allowing versatility with your test system.
-
Virginia Panel Corporation
The G12x Receiver has four removable rubber feet below the platform and also allows for permanent tabletop mounting. Available with 15" or 20" platforms. The G12x accepts ITAs designed for both the G12 and G12x allowing versatility with your test system.
-
ICS Electronics Ltd.
The ICS Electronics Limited V4 NAVTEX Test system may be used for type approval, general performance testing and production testing of NAVTEX receivers.
-
TBM300 -
Telonic Berkeley, Inc.
The Model TBM300 Portable Opacity Meter consists of two basic units connected by a single cable. The sensor unit is installed end-of-line on the exhaust outlet of the vehicle under test and contains the light source (green led) and receiver (photo detector) modules.
-
AE6920T -
Keysight Technologies
Unlike CAN, LIN, Automotive Ethernet demands rigorous compliance verification using test cases that cover transmitters (Tx), receivers (Rx), and harness/connector assemblies. To help you save time and effort, Keysight offers solutions that automate the testing and validation across Transmitter (Tx), Receiver (Rx), and the connections between Automotive Ethernet devices. Our engineers have invested thousands of hours in learning the standards and creating automated, repeatable compliance tests. These proven applications help you ensure proper test configuration and valid measurement results. Ultimately, you’ll have greater confidence that your device is compliant. Now available for data rates up to 10Gbps. The automotive Ethernet test solution AE6900T offers hardware and accessories to make sure you have all of the components you need to get up and running quickly.
-
6TL Engineering
To configure your Base Test Platform, the following parts can be added to the 6TL-19 bare half-rack:– Test Rack Manager, to control the test station.– Power Distribution Unit.– Uninterruptible Power Supply– Industrial PC or NI PXI to control the platform– 19’’ Monitor and keyboard with trackball– VPC Mass Interconnect Receiver (6 or 12 slots)– YAV Modules– Accessories: Beacon, Air inlet Pneumatic kit…– Any 19’ Instrument
-
A.H.Systems, Inc.
Our Monopole Antennas provide superior performance in electric field measurements. The Active Monopole Antenna can drive any receiver with 50W input impedance and will perform FCC, MIL-STD and TEMPEST tests. The passive rod is used for transmitting, to perform shielding effectiveness and immunity testing.
-
H71002200 -
6TL Engineering
Learn about our Build to print service for Test Platforms. The 6TL22 Platform is a perfect base for the conception of a real modular Automatic Test Equipment for low to mid manufacturing volumes.A system designed around the 6TL22 is simple, easy to maintain and cost effective. The rack is prepared for the direct integration of the three platform based receivers from Virginia Panel, the S6, G12 and G12X.
-
GSS4150 -
Spirent Federal Systems
To help developers and integrators test the airborne GNSS receiver in their GBAS landing system (GLS), Spirent has developed the GSS4150 solution. The GSS4150 is a VHF signal source generator, supporting multiple different message types, enabling you to build the solutions that power the future of aviation.
-
RF ITS -
Sterner Automation Limited
Sterner's automated test management system, combined with integrated RF technology modules, provides full functionality, including: Apply power to the device under test (DUT). Read and write blocks of data to set up and validate product EEPROM using a hard-wired communications interface. Scan transmitting devices or traveller barcodes and write the information to the DUT (the "sign-up process"). Inject an RF signal of known frequency and power level to test receiver sensitivity.
-
Kuhne electronic GmbH
Is a radio beacon, whose purpose is the investigation of the propagation of radio signals. Most radio propagation beacons use amateur radio frequencies. They can be found on LF, MF, HF, VHF, UHF, and microwave frequencies. Microwave beacons are also used as signal sources to test and calibrate antennas and receivers
-
BK9012 -
BaKo Co., Ltd
Based on the BK2120A Audio Analyzer, the BK9012 is designed to quickly test microspeakers or receivers 4~8 at a time at a rate that you’ll find hard to keep up with. It tests various frequency characteristics and also rub & buzz so you know the quality of your product is maintained. And of course, you can track the accuracy and stability of your process using the data you’ve saved on about 4 million microspeakers (based on a 6 second total test + load time) per month.
-
multiLane
An optical switch box is needed so that automated test platforms can permit the system to measure the performance of transmitters and receivers at multiple wavelengths or channels. The MLO4034 Optical Switch Box incorporates a WDM demultiplexer, integrated power meters, variable optical attenuators, and optical switches to form an integrated switch matrix. It enables receivers and transmitters to be tested at up to four wavelengths or channels.