Showing results: 1891 - 1905 of 5329 items found.
-
PI-3105 -
Pulse Instruments
This highly flexible system is designed to test a wide variety of imaging devices, from low-noise astronomy and medical devices, to military and machine-vision devices with GB/sec data rates.
-
Labodam
Labodam aniline test equipment are designed with stepless speed regulation motors to have a smoother operation and automatic alarm system with sound and light to detect end point.
-
CPC 100 -
OMICRON electronics
The patented CPC 100 primary injection test system replaces several individual testing devices. This reduces the costs for training and transport, and cuts down testing time.
-
P5573A -
Keysight Technologies
Keysight P5573A PCIe 6.0 Protocol Exerciser gives the flexibility in providing realistic traffic to devices under test and also able to emulate as a complex host system
-
Inframet
Meters offered by Inframet are basically meters designed to support calibration of test systems manufactured by Inframet. The meters can be divided into two groups:*Temperature meters*Luminance meters
-
Bestone Industrial Ltd.
This groundmeter is designed for testing ground wire of electric power net, as well as earth voltage test in the fields of household electric power system and delectric appliance application.
-
HIACC Engineering & Services Pvt. Ltd.
The pneumatic vertical shock and bump test system features an advanced design with a high degree of performance and automation. The testes is easy to use and have low maintenance requirements.
-
MS 1300 -
Meltronics Systemtech
BAPCON SIMULATOR is used to test and validate Boiler Auxiliaries Plant Control Unit (Sigma BAPCON). It has CAN interface for simulating inputs and it is a microprocessor based system.
-
HMS-3000 -
ECOPIA
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
Keystone Compliance
The reliability test program includes a number of qualification tests based on the type of product, the environment within which it is anticipated to operate in and estimated product weaknesses. Establishing an effective but practical and affordable test program can be a challenge. Reducing the number of units tested or the scope of testing might not yield a sufficient sample of results. Testing multiple units or having an expansive test program can be very time consuming and expensive. A very good resource for establishing a reliability test program is MIL-HDBK-781: Handbook for Reliability Test Methods, Plans and Environments for Engineering, Development, Qualification and Production. This handbook provides test methods, test plans and test environmental profiles which can be used in reliability testing during the development, qualification, and production of systems and equipment.
-
MS 1111 -
Meltronics Systemtech
Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out LRU and card level testing for TARANG systems of all platforms. The purpose of ATE is to provide a user-friendly environment to test the LRUs and sub-systems (individually) for their functionality, perform specific tests of each LRU / sub-system and Card Level Testing. The card level testing facilitates troubleshooting down to a faulty signal flow path. The UUT tests are carried out by injection of the stimuli generated by the computer or the programmable test equipments and the responses from UUT / test equipments are feedback to the computer for evaluation and generation of reports.
-
SG1000B/PR1000A -
Praxsym
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
Wuhan Sunma Technology Co., Ltd.
xDSL / PDH Analyzer mainly used for comprehensive transmission test of SDH/PDH network and equipment and widely applied in the R&D, manufacture, acceptance inspection, performance monitoring, maintenance and measuring of networks and equipment. The instrument SunmaFiber provided can insert and measure varieties of errors and alarms in PDH and SDH systems (including on-line and off-line test), perform performance analysis on various errors as well as modulate and test jitter signals at a max. test rate of 2488MHz (STM16).
-
Applied Image, Inc.
APPLIED IMAGE is a world leader in the field of IMAGE EVALUATION Test Targets and Test Charts. Some of the specialized test charts include camera image evaluation ISO, NIST, ANSI, and MIL standard image evaluation applications; photonic and optophotonic applications; test charts for copiers and scanner; DATAcapture and BARcode Scanning testing; Security & Identification Image Capture; and all other type of imaging industries that require quality evaluation of thier image capture systems.
-
SCR ELEKTRONIKS
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.