Showing results: 4411 - 4425 of 5329 items found.
-
Spider-80SG -
Crystal instruments
The Spider-80SG is a high precision, general purpose data acquisition device featuring strain gage measurement. This device can be used in a variety of physical and measurement tests. The Spider-80SG can acquire data from a strain gage or a wide range of measurement quantities. A variety of general purpose and strain gage based sensors are supported. The Spider-80SG is built on the proven outstanding performance and reliability of Crystal Instruments’ DSP-based hardware platform. It features the same form factor as other Spider-80X front-ends from Crystal Instruments and can be configured into one measurement system with excellent compatibility and scalability. This gives the Spider-80SG capabilities to reliably acquire data from multiple sensors and for multiple measurement quantities simultaneously.
-
780587-12 -
NI
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
780587-14 -
NI
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
780587-41 -
NI
PXIe, 300 MHz, 8x12 PXI RF Matrix Switch Module—The PXIe‑2541 is an RF signal switching matrix. With its non-blocking design, you can simultaneously connect any row or column within the switching matrix and maximize the flexibility of your test system. Isolation relays on the module disconnect unused parts of the switching matrix to maintain RF performance and high isolation. The density and bandwidth of the PXIe‑2541 is ideal for routing signals between digitizers, function generators, and other RF generators and analyzers. For higher channel count applications, you can connect multiple PXIe‑2541 modules together to create switching matrices of 8x24, 8x36, and larger.
-
778572-41 -
NI
300 MHz, 8x12 PXI RF Matrix Switch Module—The PXI‑2541 is an RF signal switching matrix. With its non-blocking design, you can simultaneously connect any row or column within the switching matrix and maximize the flexibility of your test system. Isolation relays on the module disconnect unused parts of the switching matrix to maintain RF performance and high isolation. The density and bandwidth of the PXI‑2541 is ideal for routing signals between digitizers, function generators, and other RF generators and analyzers. For higher channel count applications, you can connect multiple PXI‑2541 modules together to create switching matrices of 8x24, 8x36, and larger.
-
785672-01 -
NI
2.1 GHz, 1U Rugged Rack-Mount External Controller for PXI—The RMC‑8357 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon eight‐core processors that support up to 32 GB of RAM. The RMC‑8357 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8357 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.
-
785673-01 -
NI
2.1 GHz, 1U Rugged Rack-Mount External Controller for PXI—The RMC‑8357 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon eight‐core processors that support up to 32 GB of RAM. The RMC‑8357 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8357 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.
-
Teledyne LeCroy
Compute Express Link (CXL) is a new high-speed CPU-to-Device and CPU-to-Memory interconnect designed to accelerate next-generation data center performance. CXL technology maintains memory coherency between the CPU memory space and memory on attached devices, which allows resource sharing for higher performance, reduced software stack complexity, and lower overall system cost. This permits users to simply focus on target workloads as opposed to the redundant memory management hardware in their accelerators. CXL is based on a PCI Express 5.0 Physical layer with speeds up to 32GT/s. Teledyne LeCroy provides protocol analysis test equipment to support development and debug of CXL based devices.
-
787312-01 -
NI
PXIe, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8522 is a 1000BASE-T1 unshielded twisted pair (UTP) module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications that require Automotive Ethernet to test … and validate automotive electronic control units (ECUs). The PXIe-8522 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8522 also provides LEDs on the front panel to help you monitor the network link and activity.
-
CLIOQC Model V -
Audiomatica
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
DP-VXI-5106 -
Data Patterns Pvt. Ltd.
DP-VXI-5106, is a 32 Channel Analog Comparator Module with 32 channels of differential analog window comparators. Each channel is provided with a window comparator as well as a Level Comparator , software selectable on an independent channel basis. All the 32 channels have been grouped into four groups of 8 channels each. This allows the user to configure the comparator module based on the application to initiate alarm action to exactly meet application requirements. Each Comparator channel can be programmed to generate a VXI bus interrupt or can be masked through software. An Interrupt is generated on an individual channel basis or on a group basis. Front panel outputs of buffered TTL and a 2-CO relay contact is available for every group (4 outputs total each). Also, a common buffered TTL interrupt output and a common 2-CO relay contact is also available at the facia providing extensive flexibility in application engineering.This module is an ideal device for GO / NO-GO testing in Test Stand Automation where important signals must be continuously monitored for system shut down purposes and safety inter-lock implementation. The hardware implementation in the Comparator module provides high-speed throughput and reliable inter-lock implementation. The interrupt out signal can be further wired as trigger signals for pre and post trigger analysis of signal data for post acquisition detailing.Each channel provides a Window Comparator implementation and a Level Comparator implementation. The configuration is programmable through software and the alarm can be generated if the signal is within the window or outside the window. Similarly, a high and low limit can be set and a trigger is generated if the signal exceeds the high limit or drops below the low limit.
-
Wuhan Sunma Technology Co., Ltd.
Fiber Optic Light Sources are a necessity for performing fiber optic network testing to measure the fiber optical loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the fiber optic power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the fiber optic power meters, they act as an economic and efficient solution for the fiber optic network works. SunmaFiber offers handheld fiber optical light source and laser light source.
-
Marvin Test Solutions, Inc.
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
Komeg Technology Ind Co.,Ltd
Isolated type of burn-in room features: ●Separate the product and loading area, easy to control temperature and maintain. ●Temp. range: 40-70ºC±3/±5ºC, ●Temp. constancy: ±0.5ºC ●Uniformity: ±3ºC ●Test frame materials: painted stainless steel or a combination of forming aluminum ●Insulation: with PU foam ( doors with double glazing ) insulation, so that the internal temperature is not subject to external factors, to achieve power saving effect ●Product hierarchy placement, Selection of layer height in accordance with the requirements, convenient access ●Computer monitoring system is optional. ●Noise level:≤75dB Application Suitable for all kinds of electronic products, especially for products with heating characteristics Product and loading area should be separated Large-scale production
-
EVd-40 -
NuVant Systems, Inc.
The EVd-40 Power Tester is a pre- and post-reconditioning tool for quality control of aftermarket HEV & EV battery production. The equipment integrates a “smart” charger (Sorensen XG 1700 or Kepco KLN 1500W) with NuVant Systems high power discharge electronics. The "power test" discharges battery packs at high power (10,000 watts), while tracking module voltages. The software monitors up to 40 module voltages at a time, identifying any weak modules. The "smart" charger performs charging constant current (CC), constant voltage (CV) and complex mixed mode constant current – constant voltage (CCCV) charging protocols at voltages up to 600 V. This enables recharge of any type of rechargeable battery.