Showing results: 5281 - 5295 of 5329 items found.
-
8761A -
Keysight Technologies
The Keysight 8761A is a single-pole, double-throw coaxial switch with excellent electrical and mechanical characteristics for 50 ohm transmission systems operating from dc to 18 GHz. It features broadband operation, long life, low SWR, excellent repeatability, and magnetic latching solenoids. The Keysight 8761A switch is small and lightweight, making it ideal for applications where space is limited. Because of its versatility and excellent electrical performance, it is well suited for automated testing and systems applications.
-
MSOS104A -
Keysight Technologies
1 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.8 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Inframet
There are many low cost artificial light sources used for illumination or for industrial applications: tungsten or halogen bulbs, fluorescent lamps, LED lamps etc. Some of these sources have regulated intensity of emitted light. However, there very few calibrated light sources of precisely known parameters. A light source can be considered as calibrated when its user can precisely regulate its photometric/radiometric parameters like luminance (or illuminance), radiance (or irradiance) at defined spectrum of interest. Such light sources are needed in many applications among them, in systems for testing night vision devices, VIS-NIR cameras and SWIR imagers. Inframet offers a series of calibrated light sources that can be divides into three groups:
-
Inframet
Targets from group A are developed to support mostly testing infrared imaging systems understood as thermal imagers. These targets can be used also in testing visible/near infrared cameras or SWIR cameras but such application is not optimal. IR targets are mostly used in DT systems for testing thermal imagers and in MS systems for testing multi-spectral systems.
-
Inframet
Rotary wheels are one of basic blocks of systems for testing imaging EO systems. They are needed to enable motorized exchange of active target at collimator focal plane. There are usually 8 holes in the wheel for targets (other numbers are also possible). Wheels are covered with a black high emissivity coating (emissivity at least 0.97).
-
Inframet
Collimators are optical systems used to imitate standard targets placed in "optical infinity" (very long distance). The collimators are used for projection of image of reference targets into direction of tested imagers. According to type of optical elements used in design, collimators are divided into two groups: reflective collimators and refractive collimators. Reflective collimators due to their wide spectral range are almost exclusively used in systems for testing thermal imagers and are also preferable in systems testing TV cameras, SWIR imagers, laser systems or multi-sensor surveillance systems. Refractive collimators are mostly used in systems for testing night vision devices or TV cameras working in visible/near infrared range.
-
Inframet
Solar blind UV cameras are imaging devices optimized to detect ultraviolet light of wavelengths below about 280nm. Such cameras are insensitive against sunlight due to negligible sensitivity to visible and long wavelength UV light. Solar blind UV cameras are used in a series of applications like corona detection, fire detection, combustion analysis, plasma research, testing UV lamps, etc. However, highly sensitive corona detection is the main mass application and these devices are of crucial importance in electric power industry. These imaging devices enable easy detection of degraded insulators of high voltage transmission lines, distributions and substations. They can see the emission of UV light when discharges occur at defect insulators. From design point of view solar blind UV cameras are actually bispectral imaging systems built by combining true UV camera with typical visible camera. These bispectral imaging system generate output image as overlay of typical visible image with UV image of analyzed UV source.
-
Dewesoft d.o.o.
Internal Combustion Engine Measurement, Analysis and ThermodynamicsComplete combustion measurement and analysis system for internal combustion engine research and development, optimization and testing of ignition systems, exhaust systems, and valve control gear.
-
Dewesoft d.o.o.
Brake Noise Testing - Brake Squeal AnalysisDewesoft Brake Noise testing solution, also known as Brake Squeal, is ideal for detecting and tracking noise caused by mechanical vibration in various braking systems based on the VDA 303 guideline algorithm.
-
Dewesoft d.o.o.
Advanced Driver Assistance Systems (ADAS) TestingAll modern vehicles are now being equipped with Advanced Driver Assistance Systems (ADAS). The development of such systems requires complex testing, including the ability to control and calculate relative positions between multiple vehicles and objects in real-time. We provide an effective solution for ADAS testing with highly accurate GPS positioning systems to measure relative positions and velocity between multiple vehicles and objects.
-
Dewesoft d.o.o.
IOLITE - Data Acquisition and Real-time Control SystemData acquisition and real-time control front-end system with dual EtherCAT buses for industrial testing applications. All-in-one solution for real-time control and feedback monitoring.
-
Dewesoft d.o.o.
SIRIUS Waterproof - Rugged and Modular Data Acquisition SystemExtremely rugged (IP67 degree of protection) and fully isolated rugged data acquisition system for the most demanding testing in harsh environments. High-precision, high-dynamic, and high-bandwidth for all types of analog signals from IEPE to strain gages.
-
Shanghai Guantu Technology Co., Ltd.
GCW series combined wave generators can generate high energy surges for combined wave testing. It has the characteristics of fast rise and long pulse duration. According to different modulation components, different surge waveforms can be generated; the control system can automatically record and analyze the above surge waveforms. standard:IEC60060-4-5, IEC61643-11, UL1449-2006, GB18802.1, GB/T18802.21,
-
EVT531 -
Shanghai Dean Electrical Co., Ltd
To meet the standard test projects requirement of the international companiesTo control and analysis the programs will reduce the human careless and misjudgmentEasy to edit environment and easy to learnIt can test multiple sets of DUTs simultaneouslyWhen there are several DUTs are tested, it could identify the undesirable sets individuallyThe Impulse/Surge with waveform comparison is a non-destructive analysisPolarity testMaximum saved files will be up to 100 setsIt provides the password functionSpeeding test could save time and improve efficiencyChinese and English pages can be arbitrarily switched
-
SAT-18C -
Shaanxi Aitelong Technology Co., Ltd
SAT-18C handheld OTDR is the newest instrument designed for testing FTTx network. It is mainly used to measure the physical characteristics of optical fiber, such as the length, the transmission loss and the splice loss etc. It can also locate the faults or breaks of optical fiber. It is widely applied in the manufacture, construction and maintenance in optical fiber communication system.