Showing results: 631 - 645 of 5329 items found.
-
9200 Series -
NH Research, Inc.
12 to 144kW with either 120 or 600 V Power Modules Fast voltage, current and mode transition times Digital measurement system with hi-res waveform capture and digital chart recorder Custom waveform/profile generation Multiple safety features to protect battery Touch-panel manual interface Customer's own or NHR Enerchron™ Test Executives
-
Model 212HS -
TREK, INC.
Trek offers a unique, small, and portable Q/m analyzer which utilizes the "draw-off" toner transfer method to yield repeatable high accuracy toner charge measurements. The Trek Model 212HS Charge-to-Mass Ratio (Q/m) Test System is used to quickly and accurately determine the charge-to-mass ratio characteristics of both single and dual component electrophotographic toners and other charged particulates.
-
VTC SERIES -
EMIC Corporation
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
Guangzhou Jumho Electric Co., Ltd.
Cell phones and other wireless devices radiate powerful electromagnetic fields that can cause interference and noise in microphone signals. The interference and noise is called RF interference, which is an unwanted “signal” that occurs at the same time and frequency as a data signal. The RF interference disrupts the flow of data and degrades quality-of-service. Jumho Electric provides a cost-effective RF interference test system for GSM interference level measurement of wireless microphone.
-
TF131 -
TESTEX Testing Equipment Systems Ltd.
UV Penetration & Protection Test System. Fabric Samples are measured in a double beam spectrophotometer with an integrated sphere. The sample is scanned over the UVA and UVB regions of the spectrum and transmitted radiation is efficiently collected by the detector within the integrating sphere. The software calculates UV penetration factors and sun protection factors from the scan data. It runs on a PC under Microsoft Windows and controls the spectrophotometer, automates the measurement process and generates a printed report. PC and printer are not included.
-
RealCar Simulation Bench -
Ono Sokki
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
-
ATE-2 -
Lisun Electronics Inc.
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
MB Dynamics Inc.
Automotive squeaks occur when materials in contact rub against one another causing annoying noises from friction-induced stick-slips. Automotive itches are a special category of squeaks that can develop when rubber or plastic rubs against glass or paint. The MB Dynamics Material Compatibility Squeak & Itch Test System (MCTS) is designed and manufactured to subject contacting pairs of materials and actual vehicle parts to precisely controlled interference & motion under in-vehicle environmental conditions in order to acquire, monitor, analyze and report friction and acoustic characteristics with the objective to:
-
ViAcoustics
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
Yelo Ltd.
Yelo has a wealth of experience in developing and customizing test systems for the Travelling Wave Tube (TWT) market. TWT testers feature specialized power supplies, measurement equipment, and comprehensive control and safety systems.A rugged PLC is used to control all voltages and perform all monitoring functions. User interface and datalogging functions are provided by a supervisory PC that is electrically isolated from the PLC. Power Supplies are solid state with optical fibre barriers to ensure that all control/monitoring is carried out at safe voltages, and with maximum noise immunity. All safety interlocks are hardwired, and the testers are equipped with emergency shutdown features for added security.
-
Spectrum HS -
Teradyne, Inc.
Spectrum HS is Teradyne’s fully integrated functional test system. Optimized for real-time test of low latency buses, it’s a high-performance system delivering excellent test coverage of current and future products.
-
Bantam Plus -
Radian Research, Inc.
The Bantam Plus is the newest and most technologically advanced portable three-phase meter site test solution available for today’s metering professional. This innovative solution supplies a safe, accurate and highly versatile answer to the diverse test requirements of today’s electric metering.
-
CITE -
Digitaltest GmbH
Overall, CITE offers numerous tools to accelerate the process, guaranteeing the test quality and shortening the time to test.
-
NXA Series -
Noise eXtended Technologies S.A.S.
The NXA is a fully automated Phase Noise analyzer. Its dual channel architecture allows the system to use a cross-correlation process to cancel its internal noise floor. This reliable technique provides access to the unique noise floor performance of the DCNTS.
-
Baringa™ IR/UV -
Textron Systems
Baringa™ is a handheld, ruggedized aircraft survivability test set used to stimulate the electro-optic sensor suites on various aircraft platforms. Available in ultraviolet (UV) as well as one-color or two-color infrared (IR), Baringa simulates dynamic multi-engagement profiles and is easily reprogrammable to meet user testing needs.