Showing results: 3181 - 3195 of 14470 items found.
-
Parrot Invent
- The PCX Parrot Clip model is aimed to be used mainly for multimeter test leads.- When is hand held, is a handy device giving comfort to the operator.- The PCX Parrot Clip model is effective for direct point, hands-on measurements.- It has a length of about 130 mm so that it points with the metal tip places rather crowded with electronic components.- The PCX provides also reliable hands-free connections.- Even that is rather long the PCX model is not heavy, and therefore the weight of the probe is not affecting and forcing the connection.
-
PME-500-TR -
EUROSMC, S.A.
Before developing the system or equipment for the testing of a circuit break timer for distribution, the application information was obtained by consulting various users of this type of timer for circuit breaker. The customers consulted were from private service and maintenance companies, large industries, and of course from the Utility companies. It is essential to receive first hand information of the actual requirements and needs of each of these customers who are making these types of tests and then make a detailed study of the various alternatives offered by different manufactures of this type of circuit breaker timer.
-
60610 -
Lisle Corp.
Set includes four jumpers to fit many popular relays on Honda, Nissan, Toyota, newer Ford and GM mini micro relays as well as International trucks. Set comes in blow-molded case for storage. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using grey four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on.
-
PI-800 -
ETI Precision
The PI-800 Circuit Breaker Test System incorporates modular design and flexibility to provide unequaled capability in a portable package. The PI-800 generates continuous current of 800 amps at 4.2 kVA, with peak output to over 10x, on 120 or 240 VAC supplies. The units are housed in rugged interlocking suitcase sized enclosures. Each piece weighs no more than 125 pounds, allowing one person hand truck mobility. Basic operation is very simple, and the proven MAC-21 instrumentation provides optimal output control and measurement.
-
Applied Image, Inc.
The IMAGING GAUGETM quality analysis system was developed by APPLIED IMAGE to address the growing need to standardize the evaluation of camera image quality. The system includes a Test Chart manufactured using our ACCUedge® technology, along with unique Image Analysis Software, used together to analyze the quality of the imaging system, and then provide a summary report on the various image quality metrics. Our goal is to provide a simple to use, unique image analysis system, that can be utilized by R&D, scientists, system integrators, technicians and field operators to evaluate the camera quality or imaging system.
-
TA-2000 -
Tech-Aid Products
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
Barbour Stockwell, Inc
designs and builds all kinds of rigs for testing the components of high speed machinery. As in our spin pits, BSi's unsurpassed ability to generate and precisely control extraordinarily high speeds is the key competitive advantage. BSi engineers also draw on our vast experience to provide reliable drives and rigs to meet the most demanding requirements under the most extreme conditions. We have engineered and manufactured rigs for testing bearings at speeds to 250,000 rpm. We have delivered test benches for testing abradable seals at temperatures to 1100 deg. C.
-
MB Dynamics Inc.
Automotive squeaks occur when materials in contact rub against one another causing annoying noises from friction-induced stick-slips. Automotive itches are a special category of squeaks that can develop when rubber or plastic rubs against glass or paint. The MB Dynamics Material Compatibility Squeak & Itch Test System (MCTS) is designed and manufactured to subject contacting pairs of materials and actual vehicle parts to precisely controlled interference & motion under in-vehicle environmental conditions in order to acquire, monitor, analyze and report friction and acoustic characteristics with the objective to:
-
PAS-853BRM -
Prostat Corporation
- Surface Resistance Kit from 0.01 ohm to 9.99x1012 ohms- Nominal Full Range Tolerance Averages <±5%- Fully Automatic Resistance Range, Test Voltage and Electrification Period control- Determines if a surface is Dissipative, Conductive, or Insulative- Measures resistance point-to-point(Rtt) and point-to-ground (Rtg)- Measures resistance of Static Control Floors, ESD Work Surfaces and Packaging Material- Conforms to all ESD Association Standards for Resistive Characterization- Includes 2 each Conductive Rubber Electrodes- Packaged in a hard shell Carrying Case- Certificate of Calibration Traceable to NIST included
-
VTC SERIES -
EMIC Corporation
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
804A -
Teledyne LeCroy quantumdata
The Teledyne LeCroy rack mountable quantumdata 804A Video Test Generator is optimized for testing modern HDMI HDTVs. The 804A Video Generator support testing Ultra HDTVs in manufacturing at 4K resolutions at pixel rates up to 300 MHz. This enables testing ultra HD TVs with 4K resolutions at 24/30Hz with 4:4:4 pixel sampling and encoding as well as 4K resolutions at 50/60Hz using HDMI 2.0 using HDMI 2.0 4:2:0 pixel sampling and encoding. The 804A also supports testing with HDMI 2.0 21:9 format resolutions at or below 300 MHz.
-
ViAcoustics
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
Yelo Ltd.
Yelo has a wealth of experience in developing and customizing test systems for the Travelling Wave Tube (TWT) market. TWT testers feature specialized power supplies, measurement equipment, and comprehensive control and safety systems.A rugged PLC is used to control all voltages and perform all monitoring functions. User interface and datalogging functions are provided by a supervisory PC that is electrically isolated from the PLC. Power Supplies are solid state with optical fibre barriers to ensure that all control/monitoring is carried out at safe voltages, and with maximum noise immunity. All safety interlocks are hardwired, and the testers are equipped with emergency shutdown features for added security.
-
Chroma ATE Inc.
Support 8K SHV (Super Hi-Vision 7680x4320 / 8192x4320)Support full 8K scrolling functionIndependent signal and power module designDual-core graphics processing architecture - Increase graphics and data transmission performance - 8K Super Hi-Vision images switch in less than 200msSupport 6/8/10/12 bits color depth (12 bit only in LUT mode)Support user edited test patterns - BMP pattern format - Maxi. 300 of 8Kx4K bmp patternsSupport VDIM and PWM dimming functionSupport cross coordinates defect positioning functionSupport auto flicker adjustment (with A712306)Support gigabit Ethernet control interfaceSupport USB port for data update
-
Komeg Technology Ind Co.,Ltd
Isolated type of burn-in room features: ●Separate the product and loading area, easy to control temperature and maintain. ●Temp. range: 40-70ºC±3/±5ºC, ●Temp. constancy: ±0.5ºC ●Uniformity: ±3ºC ●Test frame materials: painted stainless steel or a combination of forming aluminum ●Insulation: with PU foam ( doors with double glazing ) insulation, so that the internal temperature is not subject to external factors, to achieve power saving effect ●Product hierarchy placement, Selection of layer height in accordance with the requirements, convenient access ●Computer monitoring system is optional. ●Noise level:≤75dB Application Suitable for all kinds of electronic products, especially for products with heating characteristics Product and loading area should be separated Large-scale production
