Showing results: 5566 - 5580 of 14432 items found.
-
TF220 -
TESTEX Testing Equipment Systems Ltd.
ICI Mace Snag Tester. To determine the tendency of fabrics to snag (pull yarn loops from fabric) in normal wear (mace snag).Provided with 4 rotating test cylinders fitted with sleeves of test fabric, mace balls with tungsten carbide points and controlled by a predetermined electronic counter.
-
JT 2122/MPV -
JTAG Technologies Inc.
The JT 2122/MPV DIOS (digital I/O scan module) increases the coverage and improves the diagnostic resolution of boundary-scan testing by extending test access to connectors and/or test points. JT 2122/MPV DIOS provides bi-directional parallel-scan access to up to 128 or 133 I/Os in a standard DIMM-168 module.
-
CalEasy Series -
Marvin Test Solutions, Inc.
CalEasy is a full-featured, Calibration Executive software package that supports the verification and calibration of Marvin Test Solutions instruments. The software is intended for use by users that prefer to perform in-house calibration and verification for their Marvin Test Solutions instruments. By calibrating or verifying the instrument in-house, the time and cost associated with returning an instrument to Marvin Test Solutions for calibration service can be eliminated or reduced. CalEasy is also used internally by Marvin Test Solutions production to perform initial calibration and to recalibrate the instrument when received for service. This ensures that user and factory based calibration performance is similar. Depending on the specific instrument, standards instrumentation supported for calibration / verification includes a DMM, and a frequency standards module. Some modules require the use of matrix switch card.
-
National Technical Systems
Hail is an extremely destructive force of nature, especially for aircraft, with impacts occurring at more than 600 mph. NTS performs hail and stone strike testing and high velocity hail strike testing. These tests can be performed using clear ice, stone and aluminum projectiles of up to two inches in diameter, fired at velocities of up to 741 miles per hour(331.4m/sec, 1087.4 f/sec). Typical test programs include aircraft windshields, antennas, radomes, and wheel/brake assemblies. Using a laser equipped system with a high degree of accuracy, repeatable impacts can be performed to within a quarter inch of the desired target. This accuracy allows NTS to test even the smallest of test samples, as well as limit the potential damage area of larger units.
-
ELES Semiconductor Equipment SpA
ELES designs and manufacturers reliability test solutions to verify the performance of integrated circuits from concept validation to high volume production during all the test phases. No other company can provide universal equipment for all the reliability tests, or can guarantee a seamless data flow between phases or can apply on chip embedded reliability engineering for data tracking and failure investigation. Clients use our functional test data to proactively analyse variations between lots, between temperature extremes and during lifetime (often these defects escape ATE). The improvements to products and processes needed to arrive at zero defects cannot be driven by the quantity of Big Data alone, the quality of reliability data is a strategic advantage that only ELES can provide.
-
QACraft
We test all types of desktop applications to ensure that the apps are robust, user-friendly, and interactive. QACraft has been working closely with several clients across the globe to test the website, desktop applications, software, and much more. Our supreme quality results have made us one of the top-rated desktop application testing services company in the USA. Right from testing the usability of all the applications to seeing the performance of the application under pressure, our team conducts several tests. The tests also include the behavior of an app under different and unusual situations to ensure the functioning of it. As we have an expert team with us, they help you to determine the issues and the errors that we need to fix for better and consistent performance.
-
National Technical Systems
Transportation simulation testing involves the application or simulation of environments found in the transport of goods and equipment. These environments may include vibration, drop or shock, temperature, loose cargo or bounce, as well as other dynamic or climatic environments. Products and equipment are usually tested in the “shipping” configuration which means they would be packed in the default shipping container or transit case during the test. However, some items may also be tested in an unpacked state if there is an expectation that they might frequently be transported in that manner. Tests are performed not only to test the effects of transport on the product itself, but also to test the adequacy of shipping container design and the interaction between product and container during shipping. There are a number of possible modes of transport for any given item subject to shipping.
-
1864-9700 -
IET Labs
The GenRad 1864 Megohmmeter is the choice for more demanding applications. The test voltage can be set to any value from 10VDC to 109VDC in 1-volt steps and to 1090VDC in 10 volt steps. Thus the GenRad 1864 can be set to any common, or uncommon test voltage for ceramic, mica or paper capacitors, or other devices. The reverse resistance of rectifiers can be readily measured; the low test voltages are especially useful in measuring solid state diodes. An additional range on the 1864 Megohmmeter permits measurements up to 200 T (2 x 1014)
-
ISequenceSpec -
Agnisys, Inc.
The complexity of modern SoC has raised the requirement for HW/SW co-simulation to catch the bugs from the early design stage. There is lack of common set of sequences which can be shared across the teams. ISepenceSpec helps design teams to generate the unified test and programming sequences in UVM and Firmware from the specification. ISequenceSpec uses the register information from importing the standard formats like IP-XACT, SystemRDL, XML. User can define the test sequences in a simple editor, and then generate the unified test sequences from verification to validation.
-
HIL 6 series -
Typhoon HIL, Inc.
With 20 ns PWM sampling time, down to 500 ns simulation time step, and ultra-low latency, 6 Series processor has set the industry standard for ultra-high fidelity real-time emulation of power electronics systems. Simply plug your controller into a Typhoon HIL 6 Series real-time emulator, without any controller modifications, and take it for the most demanding test drive ever. Test any and all imaginable operating conditions, including faults. Automate and formalize test processes with our integrated software tools.
-
Fairview Microwave Inc.
Fairview Microwave’s line of phase stable RF analyzer cables consists of 19 models designed to deliver optimal amplitude and phase stability with flexure. These portable test cables feature VSWR as low as 1.2:1 and a maximum operating frequency of 27 GHz, depending on the model. These rugged RF test cables feature crush resistance of 1,200 psi and an operating temperature range of -55°C to +105°C. These test cables for handheld RF analyzers are offered with 7/16, N, SMA, TNC or 3.5mm connector options.
-
Bitbar Inc
Selenium has already cemented its place as a de-facto web test automation standard and Appium is providing very clean high level API that can be quickly adopted by Selenium developers, as it nicely abstracts lot of the messy stuff related to running tests. Our Testdroid Cloud provides this sort of environment where everything is packaged and pre-build for your Selenium / Appium tests, using only real mobile devices (Android and iOS) and real browsers that are usable with those devices (Safari for iOS, Chrome, WebKit, Firefox and others for Android).
-
VerOCode -
Verocel, Inc.
VerOCode can use the same requirements-based tests that were used in functional testing to automate the capture and analysis of structural coverage testing without instrumenting the code under test. This is part of the process used at Verocel. It then records and displays the instructions executed in a program under test, and for conditional instructions, records and displays the state of the condition code at each execution of the instruction. Structural coverage is obtained at the machine code level using the integrated image, with results reported through an annotated program listing containing the source and machine code level expansion
-
MD-ASM-150-AWD (4×4) -
Mustang Dynamometer
The MD-ASM-150-AWD (4×4) tests both axles of the test vehicle under the same imposed load; while at the same time providing for front-to-rear axle speed synchronization. Front-to-back roller speed synchronization protects AWD center differentials, provides for a means to safely test 2WD vehicles with traction control, and allows for testing to be performed under real-world load conditions. The MD-ASM-150-AWD (4×4) accommodates wheelbases from 86 to 128 inches (218 – 325 cm) without moving parts.
-
IOL INTERACT™ -
UNH IOL
IOL INTERACT™ software expedites and automates the testing of NVMe SSDs and NVMe-oF products. It is used to test products for inclusion on the NVMe Integrator's List. Members of the UNH-IOL NVMe Testing Services are entitled to a copy of INTERACT™ for in-house testing to ensure that their products will meet the Integrator's list requirements when submitted for testing. While most test requirements can be performed with the PC edition tool, a subset of tests specific to PCIe products are only available on the Teledyne-LeCroy tool, which require low level traffic generation capability.
