Showing results: 8416 - 8430 of 14470 items found.
-
72-9940 -
Tenma
The 72-9940 is a RJ45 Cable Tester with LED meter display. The tester easily tests RJ45 and BNC network cables. It features remote testing which allows to test cables that are terminated at separate locations.
-
PG 01-2000 -
Schlöder GmbH
The test generator PG 01-2000 is suitable for insulation test and testing of the impulse withstand voltage of electrical and electronic electricity meters. The generator produce a standard pulse voltage waveform with 0,1 / 2000 μs.
-
SORAS LS -
PSE Instruments GmbH
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
PT-1 -
International Electro-Magnetics, Inc.
The PT-1 provides a simple and easy way to determine the relative polarity of coil windings. It allows for an in-process test that takes a minimum of time to perform. By placing a coil on the platform and making connection to the start and end of a winding, a test signal is induced in the winding. The induced signal is low level and completely safe for the operator. By comparing the test signal phase of the coil under the test output, the relative polarity is indicated by the Red/Green LED. The tester operates by inducing a signal voltage in the coil under test by means of a magnetic flux field. The field is generated by a coil located in the probe base. The coil configuration is designed to provide optimum field distribution. We have also applied this basic circuit to a 5-channel scanning unit.
-
Model 27012 -
Chroma ATE Inc.
To meet the high accuracy and low price requirements for LCM TV test device, Chroma 27012 that integrates the signal and power source provide a complete test solution for LCD Module. Its LVDS, TTL (Option) signal source fully complies with the digital signal standard, meanwhile with the 24V, 12V, 5V, 3.3V DC source output it is able to supply power to VDD, Backlight for LCM test without obtaining external power source. Equipped with the interface of single key to switch the Timing, Pattern and Program rapidly for test in auto or manual mode, the 27012 is able to provide a direct and convenient test environment for LCM TV by its complete hardware configuration and easy operation.
-
Model BCA6/12M -
Aplab Limited
- Instant Measurement of energy stored in a storage battery- Tests 6V or 12V Lead Acid Batteries from 2Ah to 100Ah Capacity- Suitable for any SLA, GEL or Car Flooded Batteries- Displays DC Voltage and Balance available Ah capacity of the battery- Shows the Internal Resistance of the battery- Powered by the Battery under test- Micro-processor based digital control of entire testing process- Specially designed 4-terminal probing Battery Clamp of 100A capacity- Test simulates 20-Hr discharge test (C/20) with a few seconds- Bright, back-lit LED Display for test process display- On-screen User Guidance for testing on the built-in LCD Screen- Easy to use, portable and robust housing in a custom extrusion
-
M-OTDR-502 -
Fuzhou Metricu Technology Co Ltd
Optical Time Domain Reflectometer Wavelength 1310 / 1550nm, max test range 150KM, Dynamic range 28 / 26dB, SOR standard data saving, create PDF/EXCEL format report, stable laser source, support CW/270/330/1000/2000Hz, Test fiber's length, loss, attenuation parameters and event map, locate connection point/fusion point, Automatic analysis of various linkers/fusion points, easy analyze of various events,Support saving curves number ≥30000pcs, loss test, detect the optical or optical components loss value, etc. Test IP camera, optical power meter, visual fault locator, RJ45 cable TDR test, cable tester, cable tracer, etc.
-
2132 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test. ● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
1832 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
CNR FT -
Com-Ten Industries
The force gauge Centor First is a simple and yet complete digital force gauge which uses efficient technology to simplify force measurements, in tension and compression. A big display shows the force measured in tension or compression in the unit selected by the operator: newtons, kilograms or pounds. The bar graph completes the measurement. It can be used on a test stand (manual or motorized) or as a manual force gauge.
-
National Technical Systems
As a manufacturer of computer hardware and/or software, its import to know how well you stack up to your competitors. That’s going to be the first question that your customer are going to want to know about your product – Is it easier to use? Is it faster? Is it better? Do you know? NTS can develop a detailed competitive analysis test plan to help you find out.
-
1412-BC -
IET Labs
The wide capacitance range and high resolution of the GenRad 1412-BC decade capacitance box make it exceptionally useful in both laboratory and test shop. Owing to its fine adjustment of capacitance, it is a convenient variable capacitor to use with an Impedance Comparator. The polystyrene dielectric used in the decade steps is necessary for applications requiring low dielectric absorption and constancy of both capacitance and dissipation factor with frequency.
-
NI
Digital I/O Adapter Modules for FlexRIO offer up to 54 channels of configurable digital I/O that can interface with single‐ended, differential, and serial signals at a variety of voltage levels. When combined with a large, user‐programmable FPGA, you can use these modules to solve a variety of challenges, from high‐speed communication with a device under test to emulating custom protocols in real time.
-
KU-2600 -
Kaise Corporation
4000 count LCD 2 times / secAuto / Manual Ranging1.5V R6P or AA Batteries (x2)CATⅡ600V, CATⅢ 300V compliant155(H) x 75(W) x 29(D) mm,Approx. 180gHolster, 100-50 Test Leads, 1.5V R6P Batteries (x2 & spare),Spare Fuses F14 (0.5A/250V) (x1), Spare Fuses F17 (10A/250V) (x1),
-
Fluke Corporation
Fluke Digital Multimeters (DMM's) are on more tool belts, finding more problems, than any other comparable test tools. Each design is tested to the extreme: drop, shock, humidity, you name it. Every Fluke Digital Multimeter gives you what you need: accurate measurements; consistent, reliable performance; attention to safety; and the strongest warranty available.
