Filter Results By:

Products

Applications

Manufacturers

Test

to find acceptable or limits of.

See Also: Testers, Testing, Specimen


Showing results: 9706 - 9720 of 14526 items found.

  • Electric Servo Motor Type 2 · 4 Poster Vibration Tester

    Kokusai Co., Ltd.

    It arranges four 3-axis vibration testers equipped with a high torque, ultra-low inertia servomotor to test the vibration of the finished vehicle.

  • LINE-CORD AND MULTI-WIRE CABLE TESTERS

    LCT-3 - Criterion Instruments Limited

    Model LCT-3 Line-cord tester is an automatic test set to check continuity, polarity and dielectric breakdown on three-wire line cords.

  • Embedded Analysis Software for the 2000 X-Series

    D2000GENB - Keysight Technologies

    Test and debug I²C, SPI, RS232/422/485/UART designs with triggering, decoding, and pass / fail mask limit testing.

  • Polarity Tester

    CRY5616 - CRYSOUND

    CRY5616 Polarity tester is typically designed to test the positive/negative polarity of acoustic components, such as speakers, headphones, headphone speakers, and receivers.

  • Clamp Meters

    Klein Tools, Inc.

    Measures AC current via the clamp and AC/DC voltage, resistance and continuity via test-leadsBuilt to withstand a 3.3 ft. (1m) dropCAT III 600V, Class 2, Double insulation safety ratingBacklit display for clear readingsPowers off automatically after 15 minutes of non-use to conserve battery lifeIncludes a carrying case, test leads and 3 'AAA' batteriesLow battery indicator and easily accessible battery compartmentMeets requirements for use in basic and controlled electromagnetic environments like residential, office and light-industrial locationsOperating altitude to 6,562 ft (2,000 m)Operating temp: 32°F to 122°F (0°C to 50°C)

  • Correlation Analysis

    Crystal instruments

    EDM Modal Correlation Analysis allows the user to correlate two modal models; EMA and/or FEA models. Comparing the experimental data with that acquired through finite element analysis helps in validating the test results. Users can import the geometry model and mode shape data from FEA or EMA software. A modal mapping procedure is executed to match the EMA and FEA models. After this matching procedure, the new mode shape information from FEA is interpolated and the FEA modal parameters are displayed alongside with EMA results. Finally, to observe the correlation between the results from the two methods, a Cross-MAC matrix is calculated and shown.

  • Gas Chromatography

    Shimadzu Corp.

    A gas chromatograph (GC) is an analytical instrument that measures the content of various components in a sample. The analysis performed by a gas chromatograph is called gas chromatography.Principle of gas chromatography: The sample solution injected into the instrument enters a gas stream which transports the sample into a separation tube known as the "column." (Helium or nitrogen is used as the so-called carrier gas.) The various components are separated inside the column. The detector measures the quantity of the components that exit the column. To measure a sample with an unknown concentration, a standard sample with known concentration is injected into the instrument. The standard sample peak retention time (appearance time) and area are compared to the test sample to calculate the concentration.

  • High Definition MWIR Science-Grade Camera

    FLIR X8580™ - Teledyne FLIR

    The FLIR X8580 midwave IR camera is designed for scientists and engineers who need to capture detailed imagery of high-speed events, perform custom radiometric measurements, or detect points of failure in composites, solar cells, and electronics. This thermal imaging camera combines 1280 × 1024 HD resolution with fast frame rates and integration times, allowing researchers to record stop motion on fast-moving subjects or rapid temperature changes—whether in the lab or on the test range. With a four-position motorized filter wheel and support for FLIR motorized focus lenses, the X8580 will provide higher quality recordings, save time, and mitigate frustration in dynamic acquisition environments.

  • HIGH FREQUENCY DC BIAS

    6565 SERIES - Wayne Kerr Electronics, Ltd.

    The 6565 HF DC Bias Unit is intended to be used with a Wayne Kerr 6500 analyzer, either the 6500B Precision Impedance Analyzer or the 6500P HF LCR Meter. Its function is to provide a source of DC bias current through the Device Under Test (DUT) while the analyzer is making AC measurements. Each 6565 unit can provide up to 10 A of DC current, and up to six 6565 units can be connected in parallel to supply a maximum 60 A. A digital ammeter on the front panel allows the user to see the dc bias current value and an indicator LED shows when the bias current is enabled.

  • Industrial Pressure Calibrator

    2271A - Fluke Calibration

    The Fluke Calibration 2271A Industrial Pressure Calibrator provides a complete, automated solution for calibrating a wide variety of pressure gauges and sensors. Thanks to its modular design, it can be configured to meet different needs and budgets, and expanded to cover a broad workload. The 2271A is ideal for calibration laboratories starting out in pressure calibration because it offers wide pressure measurement capabilities in a single instrument. Everything you need for calibrating pressure is included; just connect supply pressure. And your investment will stand the test of time: as your workload grows and changes, the 2271A can grow and change too. Just add measurement modules.

  • LCR Meter, Hand Held, 100 kHz, 2 kH, 20000 µF, 0.2 Gohm

    72-10465 - Tenma

    The 72-10465 from Tenma is a LCR meter in orange and grey colour. It features an easy to read dual LCD (40mm x 63mm) display measurement of 19999/1999 (main/auxiliary). It also has series and parallel measurement modes which can be used to select quality factor, loss factor, phase location angle and equivalent resistance of measure articles. Intelligent detection and five different test frequencies enable accurate readings for all sizes of capacitors and inductors. The user can also access the stored data on a PC with the included USB connection and interface software. The compact size and case make this unit far more portable than a benchtop meter.

  • Low PIM Cable Assemblies

    Fairview Microwave Inc.

    Low-PIM jumper cables feature a maximum PIM level of -155 dBc and are made with UL910 plenum-rated SPP-250-LLPL cable. The PIM levels of each cable have been fully tested with the results of those tests marked on each cable. These Low-PIM cables boast a maximum operating frequency of 6 GHz and a maximum VSWR of 1.25:1 up to 2 GHz and 1.35:1 up to 6 GHz. These Low-PIM cables are lightweight, flexible and have an operating temperature range of -55°C to +125°C and are available with 4.3-10, 7/16 DIN, N and 4.1-9.5 mini-DIN connector combinations, including right-angle connectors.

  • Mini Array+

    DORC's ZX-1 - Direct Optical Research Company

    Used primarily to measure multi fiber (MT/MPO and MT-RJ) connectors, DORC's fourth generation "ZX-1 mini Array+" is the result of 18 years of hardware and software product development. Although optimized for mutifiber connectors, the ZX-1 mini Array plus also does an excellent job of measuring single fiber PC and APC connectors. DORC's patented design is based on a variant of the Michelson configuration, and provides BOTH 2D and 3D high resolution images of the sample under test in approximately 45 seconds for multi fiber connectors and just 3-4 seconds for single fiber connectors - from the time the connector is inserted.

  • Protocol Analyzers

    International Test Instruments Corp.

    The Bus Analyzer, is capable of capturing and decoding real-time LS, FS and HS USB Transactions as well as OTG SRP, OTG HNP and OTG VBus events. It has unlimited capture length (only limited by the RAM in the analysis PC as the captured data is viewed), immediate display of very large recorded capture data (data is streamed in real-time into the tree view as it is captured from the link under test or from file so you will not have to wait before you can start analyzing the data) as well as a very small physical format which makes it a powerful companion in your laptop bag or in the lab.

  • Saluki SEL7 Series Programmable DC Electronic Load (up to 6kW)

    Saluki Technology Inc.

    The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.

Get Help