Filter Results By:

Products

Applications

Manufacturers

Testers

find the limits of a design.

See Also: Test, Testing, Audio Testers, Automotive Testers, Battery Testers, Cable Testers, Component Testers


Showing recent results 1861 - 1875 of 4654 products found.

  • Concrete Strength Testers

    Qualitest International Inc.

    This category of products comprises the range of instruments utilized to evaluate construction material strength. The range of instruments is typically considered to be two parts. The first are non-destructive field tests of compressive strength. The second are tensile field tester systems to either determine the tensile strength of an overlay or bond material, or tensile strength of anchors embedded in the concrete. The first group is pure Non-Destructive Testing where the strength of the material is determined by correlation to another parameter more easily available and readily apparent. This is typically the hardness of the concrete or the resistance to penetration by either a pin or probe. The Windsor Probe, Windsor Pin and our line of Rebound Hammers all fall within this category. These are widely used standard tests and as such have seen use throughout the world.

  • High-acceleration Shock Tester

    DP-1200-18 - King Design Industrial Co., Ltd.

    The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.

  • Bit Error Rate Tester

    100G NRZ BERT - Munich-Instruments GmbH

    The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the signal at 25 Gb/s. The OS independent GUI is easy to install and enable remote control from everywhere. The complete and compact C-BERT is a powerful and cost efficient test solution for 100G Ethernet.C-BERT MI-PE2810-4 Product sheet_rev05.

  • Multi Cable Tester

    PK-7890/7890R PanTester - Pansco, Ltd

    PANTESTER is an advanced multifunction pin-by-pin cable tester to verify cable integrity of Datacom. Telecom and Coaxial cables and displays the test results on the main unit. It includes 8 separate remote ID terminators allows one person to view test results for 8 installed cables at a time to save time and money. Capabilities including (A) Auto/ID test function – It allows users to quickly check up to 8 installed data, voice and Coax cable at a time. It displays the passed cable type, ID number and identifies crossover and reversed and faulty cable in a second. (B) Blink Hub function – It blinks the Hub/Switch port light for easy outlet and cable identification, locate corresponding outlet on Hub/Switch and identifies network activity and speed. (PK-7891 only) (C) Learning function – It makes testing cable in any quantity a snap. It memory’s stores any standard or custom configuration and performs on instant no-button check on each new cable plugged in, makes testing large quantities of cable quicker and easier. (D) Tone generator function – It allows you to send a Hi/ or Low tone on individual pin or pair and on all pins simultaneously to locate a wire break. The tone generator traces cable using a tone detectable by Net Probe (PR-06P) or any market tone probe. It will make work shorter and easier for the professional and the layman alike.

  • SCR / DIODE TESTER

    T101RSeries - Carl E. Holmes Company

    The T101R/2V DIODE and SCR tester puts the sophisticated testing capability of high-priced, specialized units into a portable package that is economically priced and easy to use. It includes provisions for checking DIODES and SCR's (includes axial leads, stud mount, and flat packs) for opens, shorts, leaks, and breakdown under actual operating conditions. The leakage test applies a continuously variable peak voltage from 0 to 2,000 volts. This test shows if the DIODE or SCR will breakdown under operating conditions and is monitored by a peak reading DC voltmeter and ammeter. A built-in current trip disconnects power if the leakage current exceeds 15 milliamps during DIODE tests or 10 milliamps during SCR tests. The SCR gating test checks gate control characteristics and provides a means of matching SCR's according to their gate-current characteristics. This test is also monitored by a DC voltmeter and ammeter. The T101R/2V is a compact 6 x 12 x 17 inches and it operates on 120 VAC, 60 Hz line voltages. An easy to use instruction plate is included inside the front cover. Unit comes with test leads and compressor block. For 120 VAC, 50 Hz models, consult the factory. Additional 240/120 VAC step down transformers is included in the 50 Hz models.

  • Digital Leakage Current Tester

    Educated Design & Development, Inc.

    Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.

  • Electronic Tire Tester

    Model BTT-5700 - Branick Industries, Inc.

    The Branick BTT-5700 was created from the ground up to be the most efficient, durable and reliable electronic tire tester available. The electronic detector accurately locates flaws that may be missed using conventional methods. A visible spark occurs at the site of a flaw and the rotation stops to allow the flaw to be marked. The adjustable height platform reduces physical strain that can often lead to workers compensation claims. The BTT-5700 also features a bi-directional variable speed electric rotation motor that is whisper quiet. The auto extend/retract ramp makes tire loading easy. Hand controls are located on a locking swing arm that can be adjusted in seconds. Four air tool ports and two electric outlets are also provided so any needed tools can be kept close for improved efficiency. A high power LED light and Medium Truck Probe are also included. All probe heads require only the push of a button to change and are available to fit all common tire sizes. And, like everything from Branick, it's made in the USA.

  • Leeb Hardness Tester

    THL500 - TMTeck Manufacturing Limited

    It is the highest brightness display in China showing all functions and parameters, easy read Largest screen Oled screen and operate,also can save lots of energy .the largest screen of Leeb hardness tester in China. Two hardness scale dual-display in the screen. Measuring direction in 360 and add the auto measure direction to make test easy and precision. Add four new hardness scales, HRA, HB for D impact device of alloy tool steel; HV for cast aluminum alloy. Add New user material function, to meet the need of user can test the special material. Test at any angle, even upside down. Wide measuring range. It can measure the hardness of all metallic materials. Direct display of hardness scales HRB, HRC, HV, HB, HS, HL and three types of strength values immediately. Seven impact devices are available for special application. Automatically identify the type of impact devices. Large capacity memory could store 600 groups (Relative to average times321 ) information including single measured value, mean value, testing data, impact direction, impact times, material and hardness scale etc. Upper and lower limit can be preset. It will alarm automatically when the result value exceeding the limit. Battery information indicates the rest capacity of the battery and the charge status. User calibration function. USB port with the PC humanity multi-functions data proceeding software. Original imported high speed thermal printer support the immediate printing function. It can save data permanently. Li rechargeable battery as the power source. Charge circuit integrated inside the instrument. Continuous working period of no less than 200 hours (EL off and no printing). Auto power off to save energy. Excellent after-sale service system for high quality products---3 years guarantee and all life maintenance. Easy to buy and comfortable to use.

  • Rockwell Hardness Tester

    Sinowon Innovation Metrology Manufacture Ltd.

    ◆ Semi-automatic intelligent Digital Rockwell Hardness tester, you can automatically test the Rockwell hardness and surface Rockwell hardness measurement;◆ Automatic variable load, automatic loading, automatic unloading, automatic conversion, automatic measurement;◆ Friendly human-computer interaction,5.2“colorful LCD screen direct display test force,loading time,conversion value and indenter type etc; ◆ Automatically calculate and display the measured value, the maximum value, the minimum value, the average value and the hardness value deviation, the display shows the resolution 0.1HR;◆ There are functions such as hardness upper and lower limit settings, tolerance alarms, data graph analysis, average and (single point) batch measurement modes;◆ Software compensation function, the machine can be ± 3HR software compensation, no need to open the top cover for mechanical adjustment;◆ With automatic hardness conversion function, according to ASTM E140 conversion, no need to check the complex hardness of the table;◆ Multi-language features, can switch Chinese, English, German, Portuguese, Turkish, Czech, Korean and other languages;◆ Built-in 2000 single data storage function and 1000 group packet data storage function, can view a single data and data analysis;◆ Optional Bluetooth wireless printer to print the measurement data, no need to manually record and write test data;◆ Optional Softhard data analysis software and Bluetooth receiver on the test data for the computer into and analysis;◆ Support FexQMS measurement of large data analysis and control software to enhance the whole plant process control, reduce material loss.

  • Conductivity Type Tester

    HS-HCTT - HenergySolar

    It is strictly designed according to the requirements of the hot-probe thermal EMF conductivity type test in standard ASTM F42: Standard Test Methods for Conductivity Type of Extrinsic Semiconductor Materials. A temperature controlling heating element is installed inside the hot probe so that the hot probe is heated automatically and its temperature is maintained in the range 40-60℃.

  • Conduit Bending Tester

    King Design Industrial Co., Ltd.

    Equipment complies with IEC 61730-2:2004 MST 33 specification.

  • Cone Penetration Tester

    DRK8096 - Shandong Drick Instruments Co., Ltd.

    Determination of compliance with national standards GB / T26991, were compact design, LCD display, automatic data collection and the corresponding statistical calculations, measurement report printout.It can connect the PC output data.The entire testing process is very simple, in full compliance with the provisions of the State Pharmacopoeia. Accurate measurement results, which has good reproducibility, stability of the system.

  • Cone Penetration Tester

    K10600 - Chongqing Kailian Yongrun Industrial Co.,Ltd.

    It is designed to make penetration test of various kinds of lubricating grease and malthene. It is equipped with standard penetrating material of lubricating grease and malthene. Conforms to GB269 and ASTM D217.

  • Contactless Voltage Tester

    VD-100 - Monacor International GmbH & Co. KG

    Induction detector for voltages of 100-600 V ~ / 50-60 HzOptical and acoustic warningCAT III 1000VIntegrated LED lampPowered by 2x1.5 V Micro battery (n. Supplied)Dimensions Ø 26 mm x 176 mmWeight 30 g

  • Contact Resistance Tester

    Haomai Electric Power Automation Co.,Ltd.

    1)DC current test:200A 2)Constant power output 3)Print the test result directly 4)Lightest weight:only 8kg