Filter Results By:

Products

Applications

Manufacturers

Testers

find the limits of a design.

See Also: Test, Testing, Audio Testers, Automotive Testers, Battery Testers, Cable Testers, Component Testers


Showing recent results 3031 - 3045 of 4519 products found.

  • Fixed high voltage insulation tester

    SVS-50M - Kharkovenergopribor Ltd.

    Fixed high voltage insulation tester SVS-50M is designed for testing the insulation properties of insulating rods, rubber boots, gloves, electrical and DIY equipment, etc. with AC high voltage with mains frequency, adjustable between 0 - 50 kV.

  • Fuel Cap Pressure Tester Kit

    FPT2600EX1 - Hickok Inc.

    Battery operated handheld tester electronically check's a fuel cap's ability to hold pressure.Complete set of cap adapters that meet EPA standards for recommended fleet coverage.Pass / Fail Standard for daily calibration checks.Brightly colored LEDs indicate NO LEAK, PASS, or FAIL test results in seconds.

  • Lead Acid Intelligent Battery Tester

    612 - ACT Meters International Ltd

    This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.

  • LED Power Driver online Tester

    WT2080-OK - Lisun Electronics Inc.

    WT2080-OK LED Power Driver on line Tester is according to GB/T 24825-2009 and IEC 62384: 2006. It suitable for LED Driver production line testing quick test (0.1s finish the testing). The WT2080-OK can test 1pc LED Driver at one time in the production line.

  • Insulating Oil Dielectric Loss Tester

    HDLT - Hention Electrical Equipment Co., Ltd.

    This integrated precious insulation oil dielectric loss tester is for measuring dielectric loss TAN and capacitance of transformer insulation oil.This is a high precision instrument; integrated with oil cup, temperature control instrument, temperature sensor, dielectric loss test bridge, AC test power, and standard capacitor, etc.

  • Insulation Multimeter / Insulation Resistance Tester

    VA588 / VA587 - Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD

    VA588 Insulation Multimeters combine a digital insulation tester with a full-featured digital multimeter in a single, compact, handheld unit, which provides for both troubleshooting and preventative maintenance. This meters are ideally suited to help you with your tasks and at a cost that is far less than buying the two products.

  • Insulation Resistance Tester, 250V to 1kV

    U1451A - Keysight Technologies

    The U1451A insulation resistance tester from the U1450A series is ideal for predictive and preventive maintenance measurement tasks in electrical and industrial applications. With its vast measurement capabilities, efficient automated report generation and high durability, you can accomplish more in a day's work.

  • Insulation Resistance Tester, 50V to 1000V

    U1452A - Keysight Technologies

    The U1452A insulation resistance tester from the U1450A series is ideal for predictive and preventive maintenance measurement tasks in electrical and industrial applications. With its vast measurement capabilities, efficient automated report generation and high durability, you can accomplish more in a day's work.

  • Mini MUTT Portable Trailer Tester

    #9003A - Innovative Products of America

    portable trailer tester for testing lights and electric brakes on light-duty type trailers (7 spade, 6 round, 5 and 4 pin). The Mini MUTT places a load on the trailer's electrical circuits to verify proper lighting function. The Mini MUTT is powered by an (optional) internal 12v battery,

  • High Voltage (Hipot) Cable Tester

    CH2 - Cirris Systems Corporation

    The easy-wire CH2 was designed for commercial, military, and aerospace applications. Running on powerful Windows-based software, the CH2 offers unrivaled testing capabilities at an unparalleled price. Compact, easy-to-use, and FAST (shorts/mis-wires detected in <1 sec for 20,000 points), the CH2 is positioned to become the ''''tester of choice'''' for high-end users.

  • 16 Channel Battery Cell Tester

    17216M - Chroma Systems Solutions, Inc.

    Chroma’s 17216M is a standalone 16 channel version of their 17011 series high precision charge/discharge tester specifically designed for Lithium-ion batteries, electrical double layer capacitors (EDLC), and lithium-ion capacitors (LIC). Suitable for product characteristics screening, cycle life testing, incoming and shipping inspection, material experiment, and balancing battery voltages.

  • Pneumatically Powered Bed of Nails Testers

    Automator Pneumatic Family - Test Electronics

    Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.

  • Network Cable Tester with Breakout Box

    PA-30R - Pansco, Ltd

    The Network Cable Tester with Breakout Box offers all the features of the STP Cable Tester with the added feature of a versatile breakout box. The breakout box allows you to create your own twisted-pair wire circuits without removing the RJ-45 connectors, and can serve as a rewiring or termination device. It allows you, for instance, to connect pin 2 at one end of the cable to pin 6 at the other, or any other combination necessary. It offers a simple-to-use, no-buttons test for shielded and unshielded twisted pair cables such as T568 A/B and 10/100 Base-T. It evaluates cables immediately upon plug-in, displaying continuity, opens, and shorts on its easy-to-read LED display. Dual color LED determines whether cable is properly wired for data use, with straight-through pinning (lights up green), or for voice communication, with crossed pinning (lights up Red).

  • Lever Handle Bed of Nails Testers

    Automator Manual Family - Test Electronics

    Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.

  • Transformer Capacity and Load Load Tester

    NRRL-H - Wuhan Nanrui Electric Co,. Ltd

    NRRL-H Transformer Capacity and Load Load Tester is developed by Wuhan NANR Electrical specifically forresolving the problem, it’s a high precision instruments developed specificallyfor transformer capacity and loss parameter measurements. It comes with a high-performancerechargeable battery, can work without external power supply, the charging timecan be measured hundreds times continuously; Meanwhile, the internal digital combinedas three-phase standardsine wave signal (not simple inverter AC output, which ensure the accuracy of eachtested project data under the non-rated conditions ), the power amplifier canprovide precise phase AC testing source; and measure transformer capacity andtransformers three-phase short-circuit loss tests without external powersource, voltage regulator, voltage booster and other auxiliary equipment,simplifying wiring, improved work efficiency greatly; the accuracy of capacitytesting results up to 100%. It can be used as two kinds of devices: Activetransformer capacity tester + transformer loss parameter tester. It can measurethe  transformer capacity, load current,load loss, short-circuit loss, impedance voltage and a series of parameters forprecision frequency measurements. The NRRL-H Transformer Capacity and Load Load Tester has a small size, light weight, high measuring accuracy,good stability, easy to operate etc., which completely replace the conventionalmethod of using multi-table transformer losses and capacity measurement method,simple to connect the wires, test and record, and have greatly improved workefficiency. It has a big screen as a graphic LCD window, graphical menuoperation and with a character prompt, set the parameters in a multi-screendisplay interface, interactive user-friendly, easy to use, is the preferred productfor electric users at all levels .