Showing recent results 3361 - 3375 of 4781 products found.
-
4101 IN - Standard Electric Works Co., Ltd
● Measures Insulation Resistance, voltage (AC-DC) measurements.● Automatic hold facility.● Continuity test with a short circuit current of minimum 200mA.● Energy conservation is feature.● EnerSave™ limits the test duration to about 10 Seconds to save energy.● No moving parts. All calibration are saved internally in a non volatile memory.● Easy calibration at any facility around the world.● Low cost maintenance, calibration, and ownership.● Complies to all the latest regulations, including UK.
-
4175 TMF - Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Telecommunication test voltage : 50V and 100V.● Large range of insulation test voltages: 50, 100, 125, 250, 500, 1000V.● Mov / protection devices test.● Gas Arrester function.● Automatic voltmeter AC/DC at Start/Reset.● Test ON-OFF.● Battery test.● Safety voltmeter before each test.● Auto-discharge on all test and all ranges.● Battery test at Switch ON-TEST.● Smart hold & Stop on voltmeter AC/DC.● eads AUTO-NULL Key.● Test Auto-stop.● Auto range.● Ener-Save™.
-
1155 TMF-M - Standard Electric Works Co., Ltd
● High Contrast OLED display.● Designed for viewing in the dark, for mining industry.● Auto-range microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto-discharge on all tests and all ranges.● Leads auto-null key.● Test auto-stop.● Smart hold and stop on voltmeter AC/DC.● Ener-Save.● Continuity short circuit >220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Polarization index (PI).● Dielectric Absorption Ratio (DAR).● BS 16 edition.
-
165 CB - Standard Electric Works Co., Ltd
● 165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.● For testing: -RJ45/RJ11 -USB -COAX -BNC cable -Multi-wire cable● Auto-scan and manual-check function● Buzzer sound warning for wire status● 2 LED module indicators on the master unit which can do both of transmitter and receiver functions for RJ45/RJ11 cable testing. Users don't need to use the receiving unit.● 165 CB provides a variety for checking cable continuity, open status, short status and miss-wired. ● Ground (shielded ) wire test.● LED indication for wire status.● Power source : 9V battery
-
SG-P07DC - Jinge Testing Machine Co.,Ltd
It’s used to determine the anti-skid characters for shoe outsole, heel or relevant materials of outsole under static status. Place the specimen levelly onto the friction board and apply the specified load, and pull it at a certain speed to get its maximum force and its friction coefficient.
-
SG-P04D - Jinge Testing Machine Co.,Ltd
Clamp the two specimens in cross shape. Based on teh various materials of the specimen, apply the appropriate load. (force). During test, the two specimens are creased and flexed reciprocally. After reaching the specified number of abrasion, take off test samples to check if they are cracked, winkled or discolored.
-
SG-P09B - Jinge Testing Machine Co.,Ltd
Compress the specimen（foam material）to between two compression plates with the reciprocating cression. Aad measure its permanent deformation rate.
-
A&D Company, Ltd.
This testing machine is used to evaluate the frictional characteristics in a pressure container. It can evaluate the frictional characteristics of refrigerants, oil, friction materials, etc. for compressors and so on. It has a load cell inside the pressure container to enable frictional-force measurement with high accuracy.
-
LCIC-4HS - Industrial Measurement Systems Ltd.
Four Channel Load Cell Interface Card Model LCIC-4HS The LCIC-4HS is a four channel load-cell interface board for the IBM PC/AT and compatible computers (ISA Bus). This board was especially designed to fit very fast and real-time weighing applications such as multi-head fillers. It supports up to four channels with one load-cell on each. All the necessary filters and the batching control functions are built on the board and are easily accessible by the user. Direct communication with the PC bus and high-frequency sampling enables the LCIC-4HS to handle all real-time applications and to achieve very high accuracy. The LCIC-4HS is memory-mapped. Up to 32 boards (128 channels) may be installed in a single PC. It comes with a detailed user manual and software utilities for easy installation and calibration as well as full examples for the programmer (including Win 95/98 drivers).
-
900-355 - Phase II Plus
Load Cell driven system provides precise control of test force application Direct digital reading Engineered to obtain highly sensitive and accurate readings Perfect for laboratories, workshops, tool rooms, inspection labs, etc. Measuring Range: 8-650HBW
-
SQA - Zoltes, Inc.
Emulate multiple POTS/ Centrex subscriber terminals with tones and voice mediaAutomation via CLI or execution from simple GUIComprehensive test results:Call statisticsFailure reasonsLadder diagrams
-
Vidac Solutions
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
TRT series - IBEKO Power AB
The TRT is a true three-phase, fully automatic test set, specially designed for a turns ratio, a phase shift, and an excitation current measurement of power, distribution, and instrument transformers. The TRT determines the transformer turns ratio by accurately measuring voltages across the unloaded transformer windings. As a test result it displays the ratio of these voltages. This ratio of voltages can also be automatically rescaled to match the physical ratio of a number of turns on a transformer high and low voltage side.
-
Basic Bert - Luceo Technologies GmbH
Already as a single channel BERT the PARALLEX® system offers full functionality for testing high speed components. PRBS and user pattern generation and error detection for 2..13Gbit/s.
-
TC-BJ100 - Westek Electronics Inc.
The Banjo Pro features convenient testing in both data and POTS environments. The black RJ45 plug is used for testing in eight conductor environments. "Just Flip It" to the red RJ11 plug for testing of two, four, and six conductor POTS environments.
