Showing recent results 3631 - 3645 of 4812 products found.
-
Static Solutions Inc.
Tests ground for all 110v electrical circuitsWill determine the status of all electrical groundsEasy to use LED lightsWarranteeProduct conforms to the ESD S.20.20 spec standardsIdentify electrical problemsUsed with the Ohm-Stat RT-1000 resistivity meter
-
WT-1 - Lisun Electronics Inc.
• Test 6 pieces at one time, suitable for mass testing in assembly line. • Measure parameter: Vrms, lrms, W, PF. • Freely set upper and lower limit for lrms, W, PF, alarm when value out of limits. • Freely set test duration in range: 0-99.9s, tested data automatically locked. • Test range: 1) Vrms: 10.0-300.0V 2) lrms: 5-999mA 3) W: 0.1-300.0W 4) PF: 0.0001-1.000 • Accuracy: 0.5% • Digital display on 6 windows is easy to read • Print port and communication port available (optional)
-
DCT1 - Draper Tools Ltd
Suitable for use on most petrol-engined vehicles including motorcycles. Comprises 300mm flexible hose, with 14mm and 18mm threaded adaptors, large easy-to-read scale (0-300psi/0-21bar) and air release valve to allow rapid retesting.
-
Shijiazhuang Zhongshi Testing Machine Co., Ltd.
This machine is used for testing the seal property of the plastic containers; it can be widely used by the manufacturers, science research department and inspection department of the plastic pilfer-proof capsule and composite cans.
-
Kokusai Co., Ltd.
This test machine is a tire wear test device that employs an electric servomotor power circulation system.
-
RPT-AAA Series - Ripley Tools LLC
Electronic testing tool designed to check the circuit integrity in new or installed cable up to 5,000 feet (1,500 meters) in lengthLED indicates DC shorts, splitters & other self-grounding devices in cable while a loud audio tone identifies the line carrying the signalEquipped with a right angle male push-on connector to maneuver in tight areas & a female push-on connector for speed toningTool includes a pocket clip & (1) AAA 1.5V battery
-
Protector Press Rods Family - Test Electronics
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Prober Press Rods Family - Test Electronics
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
RandHDPE HDPE Family - Test Electronics
HDPE plastic plates for extra easy machine ability and upgradeability. Designed for Research & Development and Pre-Production where product engineering changes are a weekly issue. The primary design focus is easy upgradeability. In R&D and Preproduction, design changes can happen every week. This fixture unlike normal test fixtures was designed to be easily taken apart and updated. Disassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for machining, drilling and wiring updates.
-
AudioJog Rack 8 - CableJoG Ltd
There are 2 rows of 9 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found. The LED's also show the possibility of high resistance or leakage connections. 2 LED's indicate a good digital network connection, either Straight through, or Crossed over.
-
Rand Press Rods Family - Test Electronics
Designed for Research & Development and Pre-Production environments to support often reoccurring product design changes. The primary design focus for this fixture is ease in applying engineering changes and resilience to the abuse of applying multiple engineering changes without damage. In R&D and Preproduction, design changes and updates can occur every week. This Rand fixture, unlike normal test fixtures was designed to be easily taken apart and updated. Constantly disassembling modifying and reassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for multiple updates requiring machining, drilling and wiring changes.
-
GT00WD00ZY - GAO Tek Inc.
*screen display*Double protection insulation*Non-contact measured resistance, safe, fast
-
SG-D08E - Jinge Testing Machine Co.,Ltd
This machine is suitable for various pressure tests, can set coordinates, machine automatic displacement test, and record test values. Use WINDOWS window Chinese screen settings. All data can be stored (test conditions, load---stroke curve, life curve, inspection report, etc.).
-
HS-PSRT - HenergySolar
It use Four Probe to test the resistivity and P/N type of wafers、ingots and all type of silicon materials.It can be used by Solar and Semiconductor industry.
-
Bestone Industrial Ltd.
This meter is a precision instrument for measuring light intensity. It is used in solar radiation measurement,solar research, physical and optical experiments, meteorology, and agriculture. I can also be used to measure glass ligh intensity to verify glass properties. For example: Measurement of light intensity through vehicle windows.